2000 TOYOTA CAMRY Vacuum hose

IG041±03
B01286
Vacuum Hose

GasketAccelerator Cable
Throttle Cable
(A/T)
Throttle Body
High±Tension Cord
Ignition Coil and No.2 Intake
Manifold Stay Assembly
EVAP Hose
Air Cleaner Hose
IAT Sensor
Connector PCV Hose
VSV Connector
for EVAP
No.2 Ignition CoilNo.1 Ignition Coil No.2 Intake
Manifold Stay
N´m (kgf´cm, ft´lbf): Specified torque

Non±reusable part
19 (195, 14)
EVAP Hose
EVAP Hose
Ignition Coil Connector
Air Cleaner Cap Ignition Coil and No.2 Intake Manifold Stay Assembly
(TMMK Made)
(TMC Made)
± IGNITION (5S±FE)IGNITION COIL
IG±5
1687 Author: Date:
IGNITION COIL
COMPONENTS

IN0253
WRONG CORRECT
IN0252
WRONG CORRECT IN±6
± INTRODUCTIONREPAIR INSTRUCTIONS
6 Author: Date:
(k) Care must be taken when jacking up and supporting the
vehicle. Be sure to lift and support the vehicle at the prop-
er locations (See page IN±8).
Cancel the parking brake on the level place and
shift the transmission in Neutral (or N position).
When jacking up the front wheels of the vehicle at
first place stoppers behind the rear wheels.
When jacking up the rear wheels of the vehicle at
first place stoppers before the front wheels.
When either the front or rear wheels only should be
jacked up, set rigid racks and place stoppers in front
and behind the other wheels on the ground.
After the vehicle is jacked up, be sure to support it
on rigid racks . It is extremely dangerous to do any
work on a vehicle raised on a jack alone, even for
a small job that can be finished quickly.
(l) Observe the following precautions to avoid damage to the
following parts:
(1) Do not open the cover or case of the ECU unless
absolutely necessary. (If the IC terminals are
touched, the IC may be destroyed by static electric-
ity.)
(2) To disconnect vacuum hoses, pull off the end, not
the middle of the hose.
(3) To pull apart electrical connectors, pull on the con-
nector itself, not the wires.
(4) Be careful not to drop electrical components, such
as sensors or relays. If they are dropped on a hard
floor, they should be replaced and not reused.
(5) When steam cleaning an engine, protect the elec-
tronic components, air filter and emission±related
components from water.
(6) Never use an impact wrench to remove or install
temperature switches or temperature sensors.
(7) When checking continuity at the wire connector, in-
sert the tester probe carefully to prevent terminals
from bending.
(8) When using a vacuum gauge, never force the hose
onto a connector that is too large. Use a step±down
adapter for adjustment. Once the hose has been
stretched, it may leak air.

IN0002
Example
± INTRODUCTIONREPAIR INSTRUCTIONS
IN±7
7 Author: Date:
(m) Installation and removal of vacuum hose:
(1) When disconnecting vacuum hoses, use tags to
identify how they should be reconnected to.
(2) After completing a job, double check that the vacu-
um hoses are properly connected. A label under the
hood shows the proper layout.
(n) Unless otherwise stated, all resistance is measured at an
ambient temperature of 20°C (68°F). Because the resis-
tance may be outside specifications if measured at high
temperatures immediately after the vehicle has been run-
ning, measurement should be made when the engine has
cooled down.

PP0JR±04
± PREPARATIONENGINE MECHANICAL (5S±FE)
PP±5
57 Author: Date:
RECOMMENDED TOOLS
09090±04020Engine Sling DeviceFor suspending engine
09200±00010Engine Adjust Kit .
09258±00030Hose Plug Set .Plug for vacuum hose, fuel hose
etc.
09904±00010Expander Set .

PP0BS±03
± PREPARATIONENGINE MECHANICAL (1MZ±FE)
PP±11
63 Author: Date:
RECOMMENDED TOOLS
09040±00010Hexagon Wrench Set .
09090±04020Engine Sling DeviceFor suspending engine
09200±00010Engine Adjust Kit .
09258±00030Hose Plug Set .Plug for the vacuum hose, fuel
hose etc.
09904±00010Expander Set .

PP0JV±04
± PREPARATIONEMISSION CONTROL (5S±FE)
PP±15
67 Author: Date:
EQUIPMENT
Torque wrench
Hose clipper
Pressure gauge
Vacuum gauge

PP0BV±03
PP±16
± PREPARATIONEMISSION CONTROL (1MZ±FE)
68 Author: Date:
EMISSION CONTROL (1MZ±FE)
EQUIPMENT
Hose clipper
MITYVAC (Hand±held vacuum pump)
Torque wrench

PP0JX±04
PP±18
± PREPARATIONSFI (5S±FE)
70 Author: Date:
RECOMMENDED TOOLS
09082±00040TOYOTA Electrical Tester.
09258±00030Hose Plug Set .Plug for vacuum hose, fuel hose
etc.