2000 Acura RL 3.5 Owner's Manual

Fluid Locations

AUTOMATI C

TRANSMISSIO N

FLUI D DIPSTIC K

(Yello w loop )

POWE R STEERIN G
FLUI D
(Re d cap )
RADIATO R CA P BRAK
E FLUI D
(Gra y cap )
ENGIN E OI L
FIL L CA P
ENGIN E
COOLAN T

RESERVOI R

WASHE R FLUI D
(Blu e cap )
ENGIN E OI L DIPSTIC K

(Orang e loop )

Maintenanc e

Engin
e Oil

Addin g Oi l
To add oil, unscrew and remove the engine oil fill cap on top of the left
valve cover. Pour in the oil, and replace the engine oil fill cap.
Tighten it securely. Wait a few minutes and recheck the oil level. Do
not fill above the upper mark; you
could damage the engine. Recommende
d Oi l
Oil is a major contributor to your
engine's performance and longevity.
Always use a premium-grade deter- gent oil. It is highly recommended
that you use Genuine Honda Motor Oil in your vehicle for as long as you
own it.
You can determine an oil's SAE
viscosity and Service Classification
from the API Service label on the oil container.
A fuel-efficient oil is recommended for your Acura. This is shown on the
API Service label by the words "Energy Conserving." This oil is
formulated to help your engine use
less fuel. The API Service label also tells you
the service classification of the oil.
Always use an oil that is labeled "API Service SJ." This service rating may
include other classifications, such as
CD. These additional classifications

are not a problem, as long as the
label also carries the SJ classification.
API SERVIC E LABE L
CONTINUED
Maintenanc e
ENGIN
E OI L FIL L CA P

Engin
e Oi l
The oil container may also display the API Certification seal. Make sure
it says "For Gasoline Engines."
API CERTIFICATIO N SEA L The SAE numbers tell you the oil's
viscosity or weight. Select the oil for
your car according to this chart.
An oil with a viscosity of 5W-30 is preferred for improved fuel economyand year-round protection in your
Acura. You may use a 10W-30 oil if the temperature in your area never

goes below 20°F( — 7°C).
Syntheti
c Oi l
You may use a synthetic motor oil if it meets the same requirements
given for conventional motor oil:energy conserving, a service
classification of SJ, and the proper
weight as shown on the chart. When using synthetic oil, you must follow
the oil and filter change intervals
given in the maintenance schedule.
Additive s
Your Acura does not need any oil additives. Purchasing additives for
the engine or transmission will not
increase your car's performance or
longevity. It only increases the cost of operating your car.
Maintenanc e Ambien
t Temperatur e

Engin
e Oi l

Changin g th e Oi l an d Filte r
Always change the oil and filter according to the time and distance (miles/kilometers) recommenda-
tions in the maintenance schedule.
The oil and filter collect contami- nants that can damage your engine if
they are not removed regularly.
Changing the oil and filter requires
special tools and access from
underneath the car. The car should
be raised on a service station-type hydraulic lift for this service. Unless
you have the knowledge and proper equipment, you should have this
maintenance done by a skilled
mechanic. 1. Run the engine until it reaches
normal operating temperature,
then shut it off.

2. Ope
n the hood and remove the

engine oil fill cap. Remove the oil
drain bolt and washer from the
bottom of the engine. Drain the oil
into an appropriate container.

3. Remov
e the oil filter and let the

remaining oil drain. A special
wrench (available from your Acura dealer) is required to remove the
filter.

CONTINUED

Maintenanc e

WASHE
R
OI
L DRAI N
BOL T OI
L
FILTE
R

Engin
e Oi l

4. Install a new oil filter according to

instructions that come with it.

5. Put a new washer on the drain bolt,

then reinstall the drain bolt.
Tighten it to:
3 3 lbf.ft (44 N.m , 4.5 kgf.m)

6. Refill the engine with the recom-

mended oil.
Engine oil change capacity
(including filter):
4.9 US qt (4.6 , 4.0 Imp qt)

7. Reinstall the engine oil fill cap.
Start the engine. The oil pressure
indicator light should go out within
five seconds. If it does not, turn off
the engine and reinspect your
work.
8. Let the engine run for several
minutes and check the drain bolt
and oil filter for leaks.
9. Turn off the engine, let it sit for
several minutes, then check the oil
level. If necessary, add oil to bring
the level to the upper mark on the

dipstick.

Improper disposal of engine oil can be
harmful to the environment. If you
change your own oil, please dispose of
the used oil properly. Put it in a sealed
container and take it to a recycling

center. Do not discard it in a trash bin

or dump it on the ground.

Maintenanc e
NOTIC
E

Coolin
g Syste m
Addin g Engin e Coolan t
If the coolant level in the reserve
tank is at or below the MIN line, add coolant to bring it up to the MAX line.
Inspect the cooling system for leaks.
This coolant should always be a mixture of 50 percent antifreeze and
50 percent water. Never add straight
antifreeze or plain water. Always use Genuine Honda
Antifreeze/Coolant. If it is not
available, you may use another
major-brand non-silicate coolant as a
temporary replacement. Make sure it is a high-quality coolant
recommended for aluminum engines.However, continued use of any non-
Honda coolant can result in
corrosion, causing the cooling system to malfunction or fail. Have
the cooling system flushed and
refilled with Honda antifreeze/
coolant as soon as possible. If the reserve tank is completely
empty, you should also check the
coolant level in the radiator.
1. Make sure the engine and radiator
are cool.

CONTINUED

Maintenanc e

RESERV
E TAN K
Removing the radiator cap
while the engine is hot can cause the coolant to spray out,
seriously scalding you.
Always let the engine and radiator cool down before
removing the radiator cap.

Coolin
g Syste m

2. Turn the radiator cap counter-
clockwise, without pressing down
on it, until it stops. This relieves
any pressure remaining in the
cooling system.

3. Remove the radiator cap by

pushing down and turning
counterclockwise.

4. The coolant level should be up to

the base of the filler neck. Add
coolant if it is low.

5. Put the radiator cap back on.

Tighten it fully.

6. Pour coolant into the reserve tank.

Fill it to halfway between the MAX
and MIN marks. Put the cap back
on the reserve tank.

Do not add any rust inhibitors or
other additives to your car's cooling
system. They may not be compatible
with the coolant or engine compo-
nents.

Maintenanc e
RADIATO
R CA P
RESERVE TAN K

Coolin
g Syste m

Replacin g Engin e Coolan t
The cooling system should be completely drained and refilled with
new coolant according to the time and distance recommendations in
the maintenance schedule. Only use Genuine Honda Antifreeze/Coolant.
Draining the coolant requires access
to the underside of the car. Unless
you have the tools and knowledge,
you should have this maintenance done by a skilled mechanic.

1. Turn the ignition ON (II). Turn
the heater temperature controldial to maximum heat (climate

control to 90°F/32°C). Turn off

the ignition. Open the hood. Make
sure the engine and radiator are

cool to the touch.

2. Remove the radiator cap.
DRAI
N PLU G
3. Loosen the drain plug on the bottom of the radiator. Thecoolant will come out through the
hole in the splash cover.

CONTINUED

Maintenanc e