2000 Acura RL 3.5 Owner's Manual

Sea
t Adjustment s

Pull the center of the horizontal switch up to raise the seat. Push it
down to lower the seat. Adjust the seat-back angle by
pushing the rear switch in thedirection you want to move. The driver's seat includes a memory
feature. Two seat positions can bestored in separate memories. You
can then select a memorized position
by pushing the appropriate memory
button. Refer to page 100 for how to memorize and select the seat
positions.

Instrument s an d Control s

Sea
t Adjustment s

Driver' s Lumba r Suppor t

Vary the lumbar support by moving the lever on the right side of theseat-back. Pivot the lever forward
until it stops, then let it return. Doing
this several times adjusts the lumbar support through its full range. Fron
t Passenger' s Sea t
Adjustment s
The seat adjustment switches are on the outside edge of the seat bottom.Push the long horizontal switch
forward or backward to move the seat bottom in that direction.
Adjust the seat-back angle by pushing the vertical switch in thedirection you want to move. Hea
d Restraint s
See page 14 for important safety
information and a warning about how to
properly position the head restraints.
The head restraints help protect you and your passengers from whiplash
and other injuries. They are most
effective when you adjust them so
the back of the occupant's head rests against the center of the restraint. A
taller person should adjust the restraint as high as possible.

CONTINUED

Instrument s an d Control s

Sea
t Adjustments , Armres t

The head restraints adjust for height and tilt. You need both hands toadjust the restraint. Do not attempt
to adjust it while driving. To raise it,
pull upward. To lower the restraint,
push the release button sideways and push the restraint down. To
adjust the tilt, pivot the head
restraint to the desired position. To remove a head restraint for
cleaning or repair, pull it up as far as
it will go. Push the release button and pull the restraint out of the seat-
back.
The lid of the console compartmentcan be used as an armrest at the
high or low position. To raise the armrest, push the button on the lid.
Make sure the armrest is securely
latched. To lower it, press the button and push the armrest down until it
latches.
Make sure the passengers' hands or
fingers are away from the armrest
before pushing it down.
Instrument s an d Control s
RELEAS
E BUTTO N
Armres
t

Pus h

Armres
t

The rear seat armrest is located at the center of the rear seat. Pivot itdown to use it.
Trunk Pass-through Cover

The pass-through cover can be opened from either side; it folds
forward onto the center armrest. Open the cover by sliding the knob
downward and pushing or pulling on
the cover. To close the cover, swing it up and push firmly on the top.
Make sure it latches properly. Make sure all items in the trunk and
those extending through the pass-
through are secured.
For security, this cover can be
locked and unlocked only with themaster key. To lock the cover, insert
the key and turn it clockwise.
Never drive with this cover open and
the trunk lid open. See Carbo n Monoxid e Hazar d on
page 49.
Instrument s an d Control s

LI
D
KNO
B

Mirror
s

Keep the inside and outside mirrors
clean and adjusted for best visibility. Be sure to adjust the mirrors before
you start driving.
The inside mirror has an automaticanti-glare mechanism. When the
AUTO switch is pushed in, the indicator will light. When the mirrorsenses light from the headlights of
the car behind you, the mirror surface will automatically darken to
reduce the glare. Adjustin
g th e Powe r Mirror s
Adjust the outside mirrors with the adjustment button on the driver'sdoor armrest:
1. Turn the ignition switch ON (II).
2. Move the selector switch to L (driver's side) or R (passenger's

side).

Instrument s an d Control s
SENSO
R

AUT O SWITC H
INDICATO
R SELECTO
R SWITC H

Mirror
s

ADJUSTMEN T BUTTO N

3. Move the mirror right, left, up or
down by pushing the adjustment

button in that direction. 4. When you finish, move the
selector switch to the center (off)
position. This turns off the adjustment button so you can't
move a mirror out of position by accidentally bumping the button.
Outside mirror positions can be
stored in the driving position
memory system (see page 100). HEATE
D MIRRO R BUTTO N
The outside mirrors are heated to re- move fog and frost. With the ignitionswitch ON (II), turn on the heaters
by pressing the button. The light in the button comes on as a reminder.
Press the button again to turn the
heaters off.
Instrument s an d Control s

Drivin
g Positio n Memor y Syste m

Your Acura has a memory feature for the steering wheel, driver's seatand outside mirror positions.
Two seat, steering wheel, and outside mirror positions, for
different drivers or driving
conditions, can be stored in separate
memories. You select a memorized
position by pushing the appropriate

button.
Storing a Driving Position in Memory
Store a driving position as explained
in this section only when the car is

parked.

1. Turn the ignition switch ON (II). You cannot add a new drivingposition in the memory unless the
ignition switch is ON (II). You can
recall a memorized position with
the ignition switch in any position.
2. Adjust the seat to a comfortable position (see page 93). Adjust
the steering wheel to acomfortable position (see page 71).

Adjust the outside mirrors for best

visibility (see page 98).
MEM
O BUTTO N
3. Press and release the MEMO button on the control panel. You
will hear a beep. Immediatelypress and hold one of the memory
buttons (1 or 2) until you hear two
beeps. The indicator light in the
memory button will come on. Thecurrent positions of the driver's

seat, steering wheel, and outside

mirrors are now stored.
Instrument s an d Control s

Drivin
g Positio n Memor y Syste m

Doing any of the following after
pressing the MEMO button will cancel the storing procedure. Not pressing a memory button
within 5 seconds. Readjusting the seat or steering

position.

Readjusting the outside mirror

position.

Each memory button stores only one driving position. Storing a new
position erases the previous setting stored in that button's memory. If
you want to add a new position while retaining the current one, use theother memory button.
All stored driving positions will be lost if your car's battery goes dead or
is disconnected. Selecting a Memorized Position
You can select memorized positions as follows.
1. Make sure the parking brake is set and the shift lever is in Park.
2. Insert the key in the ignition switch. If you do not insert the key
in the ignition switch, the steering
wheel will not adjust to the memorized position until you do. 3. Press the desired memory button
(1 or 2) until you hear a beep, then
release the button.
The system will move the seat, steering wheel and outside mirrors
to the memorized positions. The
indicator light in the selected memory button will flash during
movement. When the adjustments are complete, you will hear two
beeps and the indicator light will
remain on.

CONTINUED

Instrument s an d Control s
MEMOR
Y BUTTON S