1999 GMC C-SERIES Owners Manual

yellowblue
5-13
A. Hardwood Board
B. Swing Arm
5. Raise the vehicle to the required height.Single Drive Rear Axle
Disconnect the propshaft at the rear axle. Secure the
propshaft to the frame or crossmember.
Tandem Drive Rear Axles
-- Forward Axle Off
the Ground
Raise the front of the vehicle until the forward
tandem axle wheels are off the ground. Remove the
rearward propshaft.
Tandem Drive Rear Axle
-- Both Axles on the
Ground Due to Type of Suspension or Attached Load
Disconnect the propshaft at the forward tandem axle.
Secure the propshaft to the frame or crossmember.
If there is damage or suspected damage to the axle(s),
remove all axle shafts. Cover the hub openings to
prevent the loss of lubricant or entry of dirt or
foreign objects.
ProCarManuals.com

yellowblue
5-14
After Towing
Block the rear wheels and install axle and propeller
shafts. Check for proper phasing of universal joints.
Apply the emergency brake system before disconnecting
from the towing vehicle. Check and fill the rear axle
with oil as required.
Towing Your Vehicle From the Front
(All Wheels On the Ground)
Your vehicle may be towed on all wheels provided the
steering is working. Remember that the power brakes
and power steering will not have power assist. Vehicles
with air brakes will not have brakes. There must be a
tow bar installed between the towing vehicle and the
disabled vehicle.
Before Towing
Block the wheels of the disabled vehicle. On vehicles
with air brakes, release the emergency brake system by
compressing the brake chamber springs as outlined in
this section. (Note: This is to prevent the possibility of
the emergency brake being applied during towing.)On vehicles with hydraulic brakes, release the
parking brake fully by moving the lever to the
fully
-released position.
On vehicles equipped with an electric/hydraulic parking
brake, remove the propshaft.
Disconnect the propshaft at the rear axle (forward axle
on tandem axle models). Secure the propshaft to the
frame or crossmember.
If there is damage or suspected damage to the axle(s),
remove the axle shafts. Cover the hub openings to
prevent the loss of lubricant or entry of dirt or
foreign objects.
After Towing
Block the rear wheels and install axle and propshafts.
Check for proper phasing of universal joints. Apply
the parking brake system before disconnecting from
the towing vehicle. Check and fill rear axle with oil
as required.
ProCarManuals.com

yellowblue
5-15 Towing Your Vehicle From the Rear
(Rear Wheels Off the Ground)
Before Towing
Secure the steering wheel to maintain a straight
-ahead
position. Make certain that the front axle is not loaded
above the front axle Gross Axle Weight Rating (GAWR)
as indicated on the vehicle's Certification/Tire label.
After Towing
Block the rear wheels and release the steering. Apply the
parking brake system before disconnecting from the
towing vehicle.
Refer to the transmission shift label for
additional information.
Releasing Air-Operated Parking Brakes
If your vehicle has air brakes, you could have a special
towing problem. If your vehicle has to be towed because
you had a complete loss of air pressure from both
systems, the parking brakes may have applied. The tow
operator can release the brakes manually by using the
following steps. Then your vehicle can be towed with all
wheels or just the rear wheels on the ground.
ProCarManuals.com

yellowblue
5-16
CAUTION:

Working on air brakes without first using
the release studs to compress the springs
can lead to injury. Never work on the air
brake chambers without first using the
release studs to compress the brake springs.

When the brake springs are manually
compressed, you will have no brakes.
Release your air
-operated parking brakes
manually only to tow the vehicle. Never
drive the vehicle with the brakes released.
1. Block the wheels of the vehicle.
2. Remove the release stud and nut from the side of the
brake chamber. Some chambers have studs which are
visible at all times.
ProCarManuals.com

yellowblue
5-17
3. Remove the rubber
cap from the rear of
the chamber.
4. Put the release stud, nut and flat washer into
the chamber.
5. Turn the stud clockwise a quarter of a turn.6. Using a wrench, turn the
stud nut clockwise
several turns to release
the brakes. Follow the
same procedure to
release the other brake.
7. At the repair facility, apply air pressure of at least
70 psi (480 kPa) to the brake chambers, either from
an external air supply or the vehicle's air system.
8. Turn the stud nut counterclockwise several turns.
Remove the stud from the chamber.
9. Put the stud into the side of the chamber, and replace
the rubber cap.
ProCarManuals.com

yellowblue
5-18
Engine Overheating
You will find a coolant temperature warning gage on
your vehicle's instrument panel, as well as a LOW
COOLANT warning light. Your vehicle also has a
CHECK GAGES warning light on the instrument panel.
If Steam Is Coming From Your Engine
CAUTION:
Steam from an overheated engine can burn you
badly, even if you just open the hood. Stay away
from the engine if you see or hear steam coming
from it. Just turn it off and get everyone away
from the vehicle until it cools down. Wait until
there is no sign of steam or coolant before you
open the hood.
If you keep driving when your engine is
overheated, the liquids in it can catch fire. You or
others could be badly burned. Stop your engine if
it overheats, and get out of the vehicle until the
engine is cool.
NOTICE:
If your engine catches fire because you keep
driving with no coolant, your vehicle can be
badly damaged. The costly repairs would not be
covered by your warranty.
ProCarManuals.com

yellowblue
5-19 If No Steam Is Coming From Your Engine
If you get an engine overheat warning but see or hear no
steam, the problem may not be too serious. Sometimes
the engine can get a little too hot when you:

Climb a long hill on a hot day.

Stop after high
-speed driving.

Idle for long periods in traffic.
If you get the overheat warning with no sign of steam,
try this for a minute or so:
1. If you have an air conditioner and it's on, turn it off.
2. Turn on your heater to full hot at the highest fan
speed and open the window as necessary.
3. If you're in a traffic jam, shift to NEUTRAL (N);
otherwise, shift to the highest gear while
driving
-- DRIVE (D) for automatic transmissions.
4. If climbing a hill, downshift to raise engine and
fan speeds.If you no longer have the overheat warning, you can
drive. Just to be safe, drive slower for about 10 minutes.
If the warning doesn't come back on, you can
drive normally.
If the warning continues, pull over, stop, and park your
vehicle right away.
If there's still no sign of steam, push down the
accelerator until the engine speed is about twice as fast
as normal idle speed for at least three minutes while
you're parked. If you still have the warning, turn off the
engine and get everyone out of the vehicle until it
cools down.
You may decide not to lift the hood but to get service
help right away.
ProCarManuals.com

yellowblue
5-20
Cooling System (Gasoline Engine)
When you decide it's safe to lift the hood, here's what
you'll see:
Specialty Hood
A. Coolant Recovery Tank
B. Radiator Pressure Cap
C. Engine Fan
Sloped Hood
A. Engine Fan
B. Coolant Recovery Tank
C. Radiator Pressure Cap
ProCarManuals.com