1999 GMC C-SERIES parking brake

yellowblue
v
For example,
these symbols
are used on an
original battery:
CAUTION
POSSIBLE
INJURY
PROTECT
EYES BY
SHIELDING
CAUSTIC
BATTERY
ACID COULD
CAUSE
BURNS
AVOID
SPARKS OR
FLAMES
SPARK OR
FLAME
COULD
EXPLODE
BATTERY
These symbols
are important
for you and
your passengers
whenever your
vehicle is
driven:
DOOR LOCK
UNLOCK
FASTEN
SEAT
BELTS
POWER
WINDOW
AIR BAG
These symbols
have to do with
your lamps:
MASTER
LIGHTING
SWITCH
TURN
SIGNALS
PARKING
LAMPS
HAZARD
WARNING
FLASHER
DAYTIME
RUNNING
LAMPS
FOG LAMPS
These symbols
are on some of
your controls:
WINDSHIELD
WIPER
WINDSHIELD
WASHER
WINDSHIELD
DEFROSTER
REAR
WINDOW
DEFOGGER
VENTILATING
FAN
These symbols
are used on
warning and
indicator lights:
ENGINE
COOLANT
TEMP
BATTERY
CHARGING
SYSTEM
BRAKE
COOLANT
ENGINE OIL
PRESSURE
ANTI-LOCK
BRAKES
Here are some
other symbols
you may see:
FUSE
LIGHTER
HORN
SPEAKER
FUEL
Vehicle Symbols
These are some of the symbols you may find on your vehicle.
ProCarManuals.com

2-
yellowblue
2-1
Section 2 Features and Controls
Here you can learn about the many standard and optional features on your vehicle, and information on starting,
shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything is
working properly
-- and what to do if you have a problem.
2
-2 Keys
2
-4 Door Locks
2
-5 Theft
2
-5 New Vehicle ªBreak-Inº
2
-6 Ignition Positions
2
-7 Starting Your Gasoline Engine
2
-10 Starting Your Diesel Engine
2
-13 Engine Checks Before Operating
2
-15 Engine Coolant Heater (If Equipped)
2
-16 Diesel Engine Exhaust Brake
2
-17 Two-Speed Rear Axle Electric Shift Control
(If Equipped)
2
-20 Automatic Transmission Operation
2
-22 Manual Transmission Operation
2
-23 Parking
2
-29 Parking Over Things That Burn
2
-29 Engine Exhaust2
-30 Running Your Engine While You're Parked
(Automatic Transmission)
2
-30 Windows
2
-31 Tilt Wheel (If Equipped)
2
-32 Turn Signal/Multifunction Lever
2
-39 Trailer Brake Hand Control Valve (Option)
2
-40 Inter-Axle Differential Lock Control
(If Equipped)
2
-41 Rear Axle Differential Lock Control
(If Equipped)
2
-42 Engine Air Control (If Equipped)
2
-43 Exterior Lamps
2
-46 Interior Lamps
2
-46 Mirrors
2
-50 Instrument Panel
2
-52 Instrument Panel Cluster
2
-55 Warning Lights, Gages and Indicators
ProCarManuals.com

yellowblue
2-7
ACCESSORY (A): This position lets you use
accessories when the engine is off. To use
ACCESSORY, push in the key and turn it toward you.
LOCK (B): This position locks your ignition. You will
be able to remove your key only when the switch is in
this position.
OFF (C): This position lets you turn off the engine, but
the key can't be removed.
RUN (D): This is the position for driving and activating
the CAT diesel air inlet heater (if equipped).
START (E): This position starts your engine.
Engine Starter Over-Crank Protection
(If Equipped)
Some vehicles have an engine starter over-crank
protection system. This system includes a built
-in
temperature limiting switch to prevent internal damage
to the starter. If the starter motor overheats and shuts
off due to over
-cranking, the motor must cool down
before the switch will reset and allow you to operate the
starter. It can take up to six minutes before the starter
will work again.
Starting Your Gasoline Engine
Engines start differently. The 8th digit of your Vehicle
Identification Number (VIN) shows the code letter for
your engine. (See ªVehicle Identification Numberº in
the Index.) Follow the proper steps to start the engine.
To start a diesel engine, see ªStarting Your Diesel
Engineº in the Index.
Automatic Transmission
Set the parking brake and move your shift lever to
NEUTRAL (N) or PARK (P) if so equipped. Your
engine won't start in any other position
-- that's a
safety feature.
ProCarManuals.com

yellowblue
2-8 Manual Transmission
Set the parking brake, shift your gear selector to
NEUTRAL and hold the clutch pedal to the floor while
starting the engine.
Starter Motor Operation
1. The starter motor will disengage if you release
the key or the engine reaches a predetermined
engine speed.
2. To prevent overheating, the starter motor will
disengage after continuously operating for 15 seconds.
You must release the key from the start position to
re
-engage the starter.
3. The starter motor will not engage if the engine is
already running.
4. The starter motor will disengage if, after two
seconds, the starter pinion gear does not engage the
flywheel or there is no engine rpm signal from the
engine speed sensor.
Starting Your Engine
1. Without pushing the accelerator pedal, turn your
ignition key to START. When the engine starts, let
go of the key. The idle speed will go down as your
engine gets warm.
2. If the engine doesn't start in 10 seconds, push the
accelerator pedal all the way down and crank the
engine for five more seconds, unless it starts sooner.
3. If your engine still won't start (or starts but then
stops), it could be flooded with too much gasoline.
Wait 15 seconds to let the starter motor cool down.
Do Steps 1 through 3 again.
When the engine starts, let go of the key and the
accelerator pedal.
ProCarManuals.com

yellowblue
2-9
NOTICE:
Your engine is designed to work with the
electronics in your vehicle. If you add electrical
parts or accessories, you could change the way
the engine operates. Before adding electrical
equipment, check with your dealer. If you don't,
your engine might not perform properly.
If you ever have to have your vehicle towed, see
the part of this manual that tells how to do it
without damaging your vehicle. See ªTowing
Your Vehicleº in the Index.
Gasoline Engine Warm-Up
When you've started your engine, let it run for 20 or
30 seconds to warm up before you put a load on
the engine.
Drive at moderate speeds for the first few miles,
especially in cold weather. Running a cold engine at
high speed can damage it.
Restarting the Gasoline Engine While
Moving (Automatic Transmission)
If you have to restart the engine while the vehicle is
moving, you'll first have to shift the automatic
transmission to NEUTRAL (N). This safety feature
prevents starting the engine when the transmission is in
a drive gear.
Stopping the Gasoline Engine
Let your engine idle for a few seconds before turning it
off after you have finished driving your vehicle.
If you shift to NEUTRAL (N), set the parking brake.
If you shift to PARK (P), the auto
-apply feature will set
the parking brake.
If your vehicle has a two
-speed axle, put the range
selector in LOW. To be sure the axle has shifted into
LOW, engage the clutch and transmission the vehicle
may move slightly when you do this.
While your engine is idling before you turn it off, you
can make a list of any operational or handling concerns
to give to responsible maintenance personnel so they can
handle them right away.
Moisture will condense in a fuel tank that is almost
empty if the vehicle is not run for a while, even just
overnight under some conditions. So, it's always best to
refuel your vehicle at the end of each run.
ProCarManuals.com

yellowblue
2-10
Starting Your Diesel Engine
If you have a Caterpillar diesel engine, also refer to
your Caterpillar
Operation & Maintenance Manual for
starting procedure.
To make starting easier in cold weather (below 32F or
0C), the proper viscosity engine oil should be used. It's
also best to heat the engine oil first. You can do this by
using an engine coolant heater. A GM Automatic Ether
Injection System aids cold weather starting.
NOTICE:
Your diesel engine has an electric air intake
heater system which reduces white smoke and
helps start the engine in cold weather. Do not
spray starting fluid into the air intake where it
can contact the heater elements.
If you don't have the GM Automatic Ether
Injection System, don't use starting fluid or
you could damage your engine. If you have the
GM system, use only GM approved starting fluid
that has been tested to establish compatibility
with the air inlet heater system.
NOTICE:
If you ever have to have your vehicle towed, see
the part of this manual that tells how to do it
without damaging your vehicle. See ªTowing
Your Vehicleº in the Index.
Restarting the Diesel Engine While Moving
(Automatic Transmission)
If you have to restart the engine while the vehicle is
moving, you'll first have to shift the automatic transmission
to NEUTRAL (N). This safety feature prevents starting
the engine when the transmission is in a drive gear.
Stopping the Diesel Engine
If you have a Caterpillar diesel engine, see your
Caterpillar
Operation & Maintenance Manual.
1. Set the parking brake and shift to NEUTRAL (N) or
PARK (P).
2. Turn the ignition switch key to OFF.
If your vehicle has a two
-speed axle, see ªRear Axle,
Tw o
-Speed Electric Shift Controlº or ªRear Axle,
Tw o
-Speed Airshift Controlº in the Index.
ProCarManuals.com

yellowblue
2-18
The two-speed axle should be in low range when you
park the vehicle. Apply the parking brake, shift to
PARK (P) or NEUTRAL (N) and shut off the engine.
To operate off
-road or under a heavy load, shift into low
range when the vehicle is standing still and then operate
the transmission normally.
On the highway, with the axle in low range and
transmission in top gear, you may shift the axle to high
range by raising the switch and releasing the accelerator
momentarily. Re
-apply the accelerator after your shift.
Under light load conditions, first shift the axle into the
high range with the vehicle at a standstill and then
operate the transmission normally.
Manual Transmission
The switch for the rear axle
shift control is on the shift
lever. When the switch is
up, the rear axle is in the
high range. Push it down to
get the low range.
The two
-speed axle should be in low when you park the
vehicle. You'll need to engage the transmission, even
move the vehicle a little, to be sure the axle is in the low
range. Then apply the parking brake, shift into
NEUTRAL and shut off the engine.
Also, always start the vehicle in motion with the
two
-speed axle in the low range. When you upshift the
rear axle from low to high, move the switch up for the
high range, disengage the clutch, pause, engage the
clutch and then press down on the accelerator. When
you shift the axle down from high to low, you don't
have to clutch. Just move the switch down to low,
release the accelerator and then quickly apply it again.
ProCarManuals.com

yellowblue
2-19 Air Shift Control
(Manual Transmissions Only)
The lever for the rear axle
shift control is either at the
lower right corner of the
instrument panel or on the
shift lever.
When the lever is moved to HI, the rear axle will be in
the high range. Switch it to LOW to get the low range.
The two
-speed axle should be in LOW when you park
the vehicle.
You'll need to engage the transmission, even moving the
vehicle a little, to be sure the axle is in the low range.
Then apply the parking brake, shift into NEUTRAL and
shut off the engine.Also, always start the vehicle in motion with the
two
-speed axle in the LOW position. When you upshift
the rear axle from LOW to HI, move the lever to the
HI position, disengage the clutch, pause, engage the
clutch and then press down on the accelerator. When
you shift the axle down from HI to LOW, you don't
have to clutch. Just move the lever to LOW, release the
accelerator and then quickly press it down again.
Air Suspension (If Equipped)
Your vehicle may be equipped with the Hendrickson
HAS Series single
-axle air suspension which is designed
for single
-axle on-highway use. This feature is available
in the 19,000 lb. capacity and as a low profile option for
operations which require extra cubic capacity and a
reduced deck height.
With this air suspension system, the ride height is set
during vehicle assembly so that the vehicle has a constant
frame height. The system will then increase or decrease
air pressure in the air springs to maintain this height.
ProCarManuals.com