1998 TOYOTA LAND CRUISER brake

SA15T-04
F05181
F04386
SST
- SUSPENSION AND AXLEREAR DIFFERENTIAL CARRIER (w/ Diff. Lock)
SA-1 19
2069 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. SHIFTING REAR DIFF. LOCK
(a) Turn the ignition switch to the ON position.
(b) Shift the transfer shift lever to L position.
(c) Turn the differential lock control switch to the RR position
and lock the rear differential.
HINT:
While rotating the tires, check they are in the differential lock
condition.
(d) Disconnect the cable from the negative terminal of the
battery.
2. REMOVE 2 REAR WHEELS
Torque: 131 N´m (1,340 kgf´cm, 97 ft´lbf)
3. DRAIN HYPOID GEAR OIL
Torque: 49 N´m (500 kgf´cm, 36 ft´lbf)
4. DISCONNECT BRAKE LINES
(a) Using SST, disconnect the brake line and remove the clip.
SST 09023-00100
Torque: 15 N´m (150 kgf´cm, 11 ft´lbf)
(b) Employ the same manner described above to the other
side.
5. DISCONNECT PARKING BRAKE CABLES
(a) Remove the 2 clips, pin and disconnect the parking brake
cable from the bellcrank.
(b) Employ the same manner described above to the other
side.

SA15Y-03
F05218
Pin
Clip
ClipParking Brake Cable
 Gasket
123 (1,250, 91)
Clip
 O-Ring
49 (500, 36)
Axle Shaft (RH)
Differential Carrier
 Gasket
Axle Shaft (LH)
72 (740, 53)
106 (1,080, 78)
x10
N´m (kgf´cm, ft´lbf): Specified torque
 Non-reusable part Gasket
15 (150, 11)
Propeller Shaft
Filler Plug
49 (500, 36)
Drain Plug 
- SUSPENSION AND AXLEREAR DIFFERENTIAL CARRIER (w/ LSD)
SA-139
2089 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REAR DIFFERENTIAL CARRIER (w/ LSD)
COMPONENTS

SA164-10
SA-162
- SUSPENSION AND AXLEREAR DIFFERENTIAL CARRIER (w/ LSD)
2112 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSTALLATION
Installation is in the reverse order of removal (See page SA-141).
HINT:
After installation, fill the differential with hypoid gear oil for LSD (See page SA-95), fill the brake reservoir
with brake fluid, bleed the brake system (See page BR-4), check for leaks and check the ABS speed sensor
signal (See page DI-505).

SA15Z-04
F04386
SST
F05217
F05080
Matchmarks
- SUSPENSION AND AXLEREAR DIFFERENTIAL CARRIER (w/ LSD)
SA-141
2091 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. REMOVE 2 REAR WHEELS
Torque: 131 N´m (1,340 kgf´cm, 97 ft´lbf)
2. DRAIN HYPOID GEAR OIL
Torque: 49 N´m (500 kgf´cm, 36 ft´lbf)
3. DISCONNECT BRAKE LINES
(a) Using SST, disconnect the brake line and remove the clip.
SST 09023-00100
Torque: 15 N´m (150 kgf´cm, 11 ft´lbf)
(b) Employ the same manner described above to the other
side.
4. DISCONNECT PARKING BRAKE CABLES
(a) Remove the 2 clips, pin and disconnect the parking brake
cable from the bellcrank.
(b) Employ the same manner described above to the other
side.
5. REMOVE AXLE SHAFTS
(a) Remove the 4 nuts.
Torque: 123 N´m (1,250 kgf´cm, 90 ft´lbf)
(b) Pull out the axle shaft assembly and remove the O-ring.
NOTICE:
Be careful not to damage the oil seal.
(c) Employ the same manner described above to the other
side.
6. DISCONNECT REAR PROPELLER SHAFT
(a) Place matchmarks on the propeller shaft and differential
flange.
(b) Remove the 4 nuts, bolts, washers and disconnect the
propeller shaft.
Torque: 106 N´m (1,080 kgf´cm, 78 ft´lbf)
(c) Support the propeller shaft securely.

SA15J-02
F04387
F04389
F04390
- SUSPENSION AND AXLEREAR WHEEL HUB BOLT
SA-93
2043 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REAR WHEEL HUB BOLT
REPLACEMENT
1. REMOVE REAR WHEEL
2. REMOVE BRAKE CALIPER AND DISC
(a) Remove the 2 bolts, brake caliper and disc.
(b) Support the brake caliper securely.
3. REMOVE HUB BOLT
Using a brass bar and hammer, remove the hub bolt.
4. INSTALL HUB BOLT
Install a washer and nut to a new hub bolt, as shown in the il-
lustration, and install the hub bolt by torquing the nut.
5. INSTALL DISC AND BRAKE CALIPER
Install the disc and brake caliper with the 2 bolts.
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
6. INSTALL REAR WHEEL
Torque: 131 N´m (1,340 kgf´cm, 97 ft´lbf)

SA149-05
F05160
 Cotter Pin
 Cotter Pin
159 (1,625, 117)
 Cotter Pin
Axle Hub with Disc
Tie Rod End
ABS Speed Sensor
and Wire Harness28 (290, 21)
13 (130, 10)
Brake Caliper
Dust Cover
 Gasket
 Oil Seal
18 (185, 13)
Bearing
Claw Washer
Adjusting Nut
Lock Nut  Lock Washer
 Gasket
Flange
 Snap Ring
 Grease Cap
33 (335, 24)
x6
Steering Knuckle
 Oil Seal
 Bushing
 Bearing
147 (1,500, 108)

Steering Knuckle Arm
N´m (kgf´cm, ft´lbf) : Specified torque
 Non-reusable part

Precoated part
Steering Knuckle
8.0 (82, 71 in.´lbf)
123 (1,250, 91)
122 (1,250, 90)
28 (290, 21)

64 (650, 47)
See page SA-16
110 (1,125, 81)
- SUSPENSION AND AXLESTEERING KNUCKLE
SA-19
1969 Author
: Date
:
2004 LAND CRUISER (RM1071U)
STEERING KNUCKLE
COMPONENTS

SA28F-03
START
Preliminary Check
Tire pressure
Vehicle height
Brake dragging ROAD TEST
Does the vehicle lead/pull?
Cross switch front tire & wheel
assemblies (left & right).
Does the vehicle lead/pull in
same direction as before?
Check front wheel alignment.
Is it within specification?
Adjust front wheel alignment.Reverse the front left side
tire and rebalance it.
Does the vehicle
lead/pull to the left?
COMPLETE
Are the tires uni-directional type?
Choose the position of front tire & wheel
assemblies where there is least amount of pull.
Increase left front camber and decrease
right front camber until lead/pull is eliminated.Increase right front camber and decrease
left front camber until lead/pull is eliminated.
NO
YES
YES
NO
YES
YES
NO
YES
NO COMPLETE
NONOYES NOIs there steering
off center?
Adjust front tie rods.
NO
YES
Is the lead/pull stronger
than before?
YES
NOTICE : Do not exceed 1° of cross camber.
Do not exceed adjustment range.
Select a flat road where the vehicle can be driven in a straight line for 100 meters at a constant speed
of 35mph. Please confirm safety and set the steering wheel to its straight position. Drive the vehicle in
a straight line for 100 meters at a constant speed of 35mph without holding the steering wheel.
(1) The vehicle can keep straight but the steering wheel has some angle.
STEERING OFF CENTER (See page SR-10)
(2) The vehicle cannot keep straight.
STEERING PULL
YES NO
YES ROAD TEST
Does the vehicle still lead/pull?
NO ROAD TEST
Does the vehicle still lead/pull? ROAD TEST
Does the vehicle still lead/pull?
ROAD TEST
Does the vehicle still lead/pull?NO
Contact your local retail tire distributor.YES
*
*
- SUSPENSION AND AXLETROUBLESHOOTING
SA-3
1953 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REPAIR PROCEDURES
HINT:
This is a flow chart for vehicle pull.

D02869
12
4
3 5
1 4
3 5 2 1
1 2 3 4
52
3 4
5
Free " Lock
Lock " Free
D04311
Heater main relay:
1 42
5
3
1 2
3
4
5
*
*:Relay housing
metallic parts
D02663
Motor actuator side: TR-50
- TRANSFERMOTOR SHIFT CONTROL SYSTEM
1938 Author
: Date
:
2004 LAND CRUISER (RM1071U)
4. INSPECT ACTUATOR OPERATION
(a) Raise up the front wheels, place the stopper under the
rear wheels to block them, and pull up the parking brake.
(b) Disconnect the connector of the actuator and connect it
to the relay using wire.
(c) Check that the front propeller shaft can be rotated by
hand.
Inspection ItemStandard
Center Diff.
Free " LockFront propeller shaft cannot be rotated.
Center Diff.
Lock " FreeFront propeller shaft can be rotated.
HINT:
When inspecting the operation described above, use a heater
main relay.
NOTICE:
Connect the terminals being careful not to touch the neigh-
boring terminals or metallic parts of relay housing.
5. INSPECT MOTOR ACTUATOR (MOTOR)
(a) Remove the motor actuator (See page TR-8).
(b) Measure the resistance between the terminals 1 and 5.
Standard resistance: 0.3 - 100 W
(c) Measure the resistance between the terminals 1 or 5 and
body ground.
Standard resistance: More than 0.5 MW
If the resistance value is not as specified, replace the motor ac-
tuator.