1998 TOYOTA LAND CRUISER tires
[x] Cancel search: tiresPage 809 of 3115
- DIAGNOSTICSABS & VEHICLE STABILITY CONTROL (VSC) &
BRAKE ASSIST (BA) SYSTEMDI-557
750 Author: Date:
2004 LAND CRUISER (RM1071U)
DTC C1237 / 37 Tires of Different Size
CIRCUIT DESCRIPTION
DTC No.DTC Detecting ConditionTrouble Area
C1237 / 37
Driving at more than 19 mph (30 km/h) for more than 20
seconds with 1 or 2 tires of different size 3 times continu-
ously.Tire size
Skid control ECU
INSPECTION PROCEDURE
1 Check tire size.
CHECK:
Check the size and condition of all 4 wheels.
NG Replace tires so that all 4 tires are of the same
size.
OK
Check and replace skid control ECU.
DIC9M-01
Page 894 of 3115
DIC8V-01
DI-518- DIAGNOSTICSABS & VEHICLE STABILITY CONTROL (VSC) &
BRAKE ASSIST (BA) SYSTEM
711 Author: Date:
2004 LAND CRUISER (RM1071U)
DIAGNOSTIC TROUBLE CODE CHART
NOTICE:
When removing the part, turn the ignition switch OFF.
HINT:
Using SST 09843-18020 or 09843-18040, connect terminals Tc and E1 of the DLC1 or Tc and CG
of the DLC3.
If any abnormality is not found when inspecting parts, inspect the ECU.
If a malfunction code is displayed during the DTC check, check the circuit listed that code. For details
of each code, turn to the page referred to under the ºSee pageº for respective ºDTC No.º in the DTC
chart.
DTC chart of ABS:
DTC No.
(See Page)Detection ItemTrouble Area
C0278 / 11
(DI-531)Open or short in ABS solenoid relay circuitABS solenoid relay
C0279 / 12
(DI-531)B+ short in ABS solenoid relay circuit
ABS solenoid relay
ABS solenoid relay circuit
C0226 / 21
(DI-528)Open or short in hydraulic brake booster solenoid circuit (SFR
circuit)Hydraulic brake booster
SFRR or SFRH circuit
C0236 / 22
(DI-528)Open or short in hydraulic brake booster solenoid circuit (SFL
circuit)Hydraulic brake booster
SFLR or SFLH circuit
C0246 / 23
(DI-528)Open or short in hydraulic brake booster solenoid circuit (SRR
circuit)Hydraulic brake booster
SRRR or SRRH circuit
C0256 / 24
(DI-528)Open or short in hydraulic brake booster solenoid circuit (SRL
circuit)Hydraulic brake booster
SRLR or SRLH circuit
C1225 / 25
(DI-543)Open or short in hydraulic brake booster solenoid circuit (SA1
circuit)Hydraulic brake booster
SA1 circuit
C1226 / 26
(DI-543)Open or short in hydraulic brake booster solenoid circuit (SA2
circuit)Hydraulic brake booster
SA2 circuit
C1227 / 27
(DI-543)Open or short in hydraulic brake booster
solenoid circuit (SA3 circuit)Hydraulic brake booster
SA3 circuit
C1228 / 28
(DI-543)Open or short in hydraulic brake booster solenoid circuit (STR
circuit)Hydraulic brake booster
STR circuit
C0200 / 31*1
(DI-615)Right front wheel speed sensor signal malfunction
C0205 / 32*1
(DI-615)Left front wheel speed sensor signal malfunctionRight front, left front, right rear and left rear speed sensor
Eh d i itC0210 / 33*1
(DI-615)Right rear wheel speed sensor signal malfunction
Each speed sensor circuit
Sensor rotor
C0215 / 34*1
(DI-615)Left rear wheel speed sensor signal malfunction
C1235 / 35
(DI-615)Foreign matter is attached on the tip of the right front sensorRight front, left front, right rear, left rear speed sensor
C1236 / 36
(DI-615)Foreign matter is attached on the tip of the left front sensor
Right front, left front, right rear, left rear s eed sensor
Sensor rotor
C1237 / 37
(DI-557)Size of some tires is different from the other tiresTire size
Page 2478 of 3115
MA02P-02
- MAINTENANCEOUTSIDE VEHICLE
MA-1
49 Author: Date:
2004 LAND CRUISER (RM1071U)
OUTSIDE VEHICLE
GENERAL MAINTENANCE
These are some maintenance and inspection items which are considered to be the owner's responsibility.
They can be done by the owner or they can have them done at a service shop. These items include those
which should be checked on a daily basis, those which, in most cases, do not require (special) tools and
those which are considered to be reasonable for the owner to do. Items and procedures for general mainte-
nance are as follows.
1. GENERAL NOTES
Maintenance items may very from country and country. Check the owner's manual supplement in
which the maintenance schedule is shown.
Every service items in the periodic maintenance schedule must be performed.
Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).
Maintenance service after the last period should be performed at the same time interval as before un-
less otherwise noted.
Failure to do even one item an cause the engine to run poorly and increase exhaust emissions.
2. TIRES
(a) Check the pressure with a gauge. If necessary, adjust.
(b) Check for cuts, damage or excessive wear.
3. WHEEL NUTS
When checking the tires, check the nuts for looseness or for missing nuts. If necessary, tighten them.
4. TIRE ROTATION
Check the owner's manual supplement in which the maintenance schedule is shown.
5. WINDSHIELD WIPER BLADES
Check for wear or cracks whenever they do not wipe clean. If necessary, replace.
6. FLUID LEAKS
(a) Check underneath for leaking fuel, oil, water or other fluid.
(b) If you smell gasoline fumes or notice any leak, have the cause found and corrected.
7. DOORS AND ENGINE HOOD
(a) Check that all doors and the tailgate operate smoothly, and that all larches lock securely.
(b) Check that the engine hood secondary latch secures the hood from opening when the primary latch
is released.
Page 2695 of 3115
H20935
Width
Inner Diam.
AB0158
SSTBattery
H20936
Tires
(5 or More)
R05403
RS-64
- SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
2339 Author: Date:
2004 LAND CRUISER (RM1071U)
(2) Position the curtain shield airbag assembly inside
the tire with the airbag deployment direction facing
inside.
Tire size: Must exceed the following dimensions-
Width: 185 mm (7.28 in.)
Inner diameter: 360 mm (14.17 in.)
CAUTION:
Make sure that the wire harness is tight. It is very danger-
ous when a loose wire harness results in the curtain shield
airbag assembly coming free due to the shock from the air-
bag deploying.
NOTICE:
The tire will be marked by the airbag deployment, so when
disposing of the airbag use a redundant tire.
(d) Check the function of the SST (See step 1-(a) on page
RS-20).
SST 09082-00700
(e) Place the tires.
CAUTION:
Place the tire so that the deployment direction of the cur-
tain shield airbag will be downward.
(1) Place at least 2 tires under the tire to which the side
airbag assembly is tied.
(2) Place at least 2 tires over the tire to which the side
airbag assembly is tied. The top tire should have the
wheel installed.
(3) Tie the tires together with 2 wire harnesses.
CAUTION:
Make sure that the wire harnesses are tight. It is very dan-
gerous when loose wire harness results in the tires coming
free due to the shock from the airbag deploying.
HINT:
Place the SST connector and wire harness inside tires. Secure
at least 1 m (3 ft) of slack for the wire harness.
Page 2717 of 3115
AB0158
Battery
SST
H05001
Tires
(5 or more)
R05403
R09690
Battery
SSTFront Passenger
Airbag Assembly
10 mm (33 ft) or more RS-38
- SUPPLEMENTAL RESTRAINT SYSTEMFRONT PASSENGER AIRBAG ASSEMBLY
2313 Author: Date:
2004 LAND CRUISER (RM1071U)
(c) Check the functioning of the SST
(See step 1-(a) on page RS-20).
SST 09082-00700
(d) Place tires.
(1) Place at least 2 tires under the tire to which the front
passenger airbag assembly is tied.
(2) Place at least 2 tires over the tire to which the front
passenger airbag assembly is tied. The top tire
should have the wheel installed.
(3) Tie the tires together with 2 wire harnesses.
CAUTION:
Make sure that the wire harnesses are tight. It is very dan-
gerous if loose wire harnesses result in the tires coming
free due to the shock from the airbag deploying.
HINT:
Place the SST connector and wire harness inside tires. Provide
at least 1 m (3 ft) of slack for the wire harness.
(e) Install the SST.
Connect the connector of the SST to the front passenger
airbag assembly connector.
SST 09082-00700, 09082-00780
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock the secondary lock of the twin lock. Also, se-
cure some slack for the SST wire harness inside the tires.
(f) Deploy the airbag.
(1) Connect the red clip to the battery positive (+) termi-
nal and the black clip to the battery negative (-) ter-
minal.
(2) Confirm that no one is within 10 m (33 ft) area
around the tire which the front passenger airbag as-
sembly is tied to.
(3) Press the SST activation switch and deploy the air-
bag.
HINT:
The airbag deploys as the LED of the SST activation switch
comes on.
Page 2731 of 3115
H17498
Tires
(5 or More)
R05403
H1749610 m (33 ft) or more SSTBattery
Side Airbag
Assembly
RS-52
- SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG ASSEMBLY
2327 Author: Date:
2004 LAND CRUISER (RM1071U)
(d) Place the tires.
(1) Place at least 2 tires under the tire to which the side
airbag assembly is tied.
(2) Place at least 2 tires over the tire to which the side
airbag assembly is tied. The top tire should have the
wheel installed.
(3) Tie the tires together with 2 wire harnesses.
CAUTION:
Make sure that the wire harnesses are tight. It is very dan-
gerous when loose wire harness results in the tires coming
free due to the shock from the airbag deployment.
HINT:
Place the SST connector and wire harness inside tires. Secure
at least 1 m (3 ft) of slack for the wire harness.
(e) Install the SST.
Connect the connectors of the SST to the side airbag as-
sembly connector.
SST 09082-00700, 09082-00750
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock the secondary lock of the twin lock. Also, se-
cure some slack for the SST wire harness inside the tire.
(f) Deploy the airbag.
(1) Connect the SST red clip to the battery positive (+)
terminal and the black clip to the battery negative
(-) terminal.
(2) Check that no one is within 10 m (33 ft) area around
the tire which the side airbag assembly is tied to.
(3) Press the SST activation switch and deploy the air-
bag.
HINT:
The airbag deploys as the LED of the SST activation switch
comes on.
Page 2784 of 3115
H20059
SST
R13763
10 m (33 ft) or more SSTBattery
H00401Weight
X Y
Y
- SUPPLEMENTAL RESTRAINT SYSTEMSTEERING WHEEL PAD AND SPIRAL CABLE
RS-25
2300 Author: Date:
2004 LAND CRUISER (RM1071U)
(d) Install the SST.
CAUTION:
Place the disc wheel on the level ground.
(1) Connect the connector of the SST.
SST 09082-00700
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock the secondary lock of the twin lock. Also, se-
cure some slack for the SST wire harness inside the disc
wheel.
(2) Move the SST at least 10 m (33 ft) away from the
steering wheel pad tied down on the disc wheel.
(e) Cover the steering wheel pad with a cardboard box or
tires.
Covering method using a cardboard box:
Cover the steering wheel pad with the cardboard
box and weight the cardboard box down in 4 places
with at least 190 N (20 kg, 44 lb).
Size of cardboard box:
Must exceed the following dimensions:
X = 460 mm (18.11 in.)
Y = 650 mm (25.59 in.)
NOTICE:
When dimension Y of the cardboard box exceeds the
diameter of the disc wheel with tire to which the steer-
ing wheel pad is tied, X should be the following size.
X = 460 mm (18.11 in.) + width of tire
If a cardboard box smaller than the specified size is
used, the cardboard box will be broken by the shock
from the airbag deployment.
Page 2785 of 3115
R04211
Inner Diam.
Tires
(3 or More)Width
R13763
10 m (33 ft) or more SSTBattery
AB0166
RS-26
- SUPPLEMENTAL RESTRAINT SYSTEMSTEERING WHEEL PAD AND SPIRAL CABLE
2301 Author: Date:
2004 LAND CRUISER (RM1071U)
Covering method using tires:
Place at least 3 tires with no disc wheels on top of
the tire with disc wheel to which the steering wheel
pad is tied.
Tire size: Must exceed the following dimensions-
Width: 185 mm (7.28 in.)
Inner diameter: 360 mm (14.17 in.)
CAUTION:
Do not use tires with disc wheels.
NOTICE:
The tires may be marked by the airbag deployment, so use
the redundant tires.
(f) Deploy the airbag.
(1) Connect the red clip of the SST to the battery posi-
tive (+) terminal and the black clip to the battery neg-
ative (-) terminal.
(2) Check that no one is within 10 m (33 ft) area around
the disc wheel which the steering wheel pad is tied
to.
(3) Press the SST activation switch and deploy the air-
bag.
HINT:
The airbag deploys as the LED of the SST activation switch
comes on.
(g) Dispose of the steering wheel pad (with airbag).
CAUTION:
The steering wheel pad is very hot when the airbag is
deployed, so leave it alone for at least 30 minutes af-
ter deployment.
Use gloves and safety glasses when handling a steer-
ing wheel pad with deployed airbag.
Always wash your hands with water after completing
the operation.
Do not apply water, etc. to a steering wheel pad with
deployed airbag.
(1) Remove the steering wheel pad from the disc
wheel.
(2) Place the steering wheel pad in a plastic bag, tie the
end tightly and dispose of it as the other general
parts disposal.