DI-96
- DIAGNOSTICSENGINE
289 Author: Date:
2004 LAND CRUISER (RM1071U)
4 Check if DTC output recur.
PREPARATION:
(a) Clear the DTC (See page DI-3).
(b) Start the engine.
(c) Run the engine at idle for 15 seconds or more.
CHECK:
Read the DTC (See page DI-3).
RESULT:
Display (DTC Output)Proceed to
ºP0120, P0122, P0123, P0220, P0222, P0223 and/or P2135º are output
againA
No DTC outputB
B System is OK.
A
Replace ECM (See page SF-60).
DI-100
- DIAGNOSTICSENGINE
293 Author: Date:
2004 LAND CRUISER (RM1071U)
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever the follow-
ing DTCs are not presentSee ºList of Disable a Monitorº table (on page DI-3)
Fuel cutOFF
EngineRunning
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
Time until ºengine coolant temperatureº detection temperature reaches feedback start temperature
When the temperature at the time of engine starting is
10°C (50°F) or moreEngine coolant temperature is less than ºclosed-loop enable temperatureº
when 2 min. or more after engine start
When the temperature at the time of engine starting is
º-6.6°C (20°F)º to º10°C (50°F)ºEngine coolant temperature is less than ºclosed-loop enable temperatureº
when 5 min. or more after engine start
When the temperature at the time of engine starting is
-6.6°C (20°F) or lessEngine coolant temperature is less than ºclosed-loop enable temperatureº
when 20 min. or more after engine start
INSPECTION PROCEDURE
HINT:
If DTC P0115, P0116, P0117, P0118 and P0125 are output simultaneously, engine coolant tempera-
ture sensor circuit may be open or short. Perform the troubleshooting of DTC P0115, P0117 or P0118
first.
Read freeze frame data using the hand-held tester or the OBD II scan tool. Freeze frame data records
the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can
help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel
ratio was lean or rich, as well as other data from the time when a malfunction occurred.
1 Are there any other codes (besides DTC P0125) being output?
PREPARATION:
(a) Connect the hand-held tester or the OBD II scan tool to the DLC3.
(b) Turn the ignition switch ON and push the hand-held tester or OBD II scan tool main switch ON.
(c) When using hand-held tester, enter the following menus: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / CURRENT CODES.
CHECK:
Read the DTCs using the hand-held tester or the OBD II scan tool.
RESULT:
Display (DTC output)Proceed to
P0125A
ºP0125º and other DTCsB
HINT:
If any other codes besides ºP0125º are output, perform the troubleshooting for those DTCs first.
B Go to relevant DTC chart (See page DI-36).
A
DI-104
- DIAGNOSTICSENGINE
297 Author: Date:
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester or the OBD II scan tool. Freeze frame data records the
engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help deter-
mine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean
or rich, as well as other data from the time when a malfunction occurred.
1 Are there any other codes (besides DTC P0128) being output?
PREPARATION:
(a) Connect the hand-held tester or the OBD II scan tool to the DLC3.
(b) Turn the ignition switch ON and push the hand-held tester or OBD II scan tool main switch ON.
(c) When using hand-held tester, enter the following menus: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / CURRENT CODES.
CHECK:
Read the DTC using the hand-held tester or the OBD II scan tool.
RESULT:
Display (DTC Output)Proceed to
P0128A
P0128 and other DTCsB
HINT:
If any other codes besides P0128 are output, perform the troubleshooting for those DTCs first.
B Go to relevant DTC chart (See page DI-36).
A
2 Check cooling system.
CHECK:
Check that there is a defect in the cooling system which causes over-cool, such as abnormal radiator fan
operation, modified cooling system and so on.
NG Repair or replace cooling system.
OK
+25 %
-12.5 %
More than 0.5 V
Less than 0.4 V
Case 1
Case 2
Case 3
Case 4
Output voltage of heated oxygen
sensor (sensor 1: front sensor)
Injection volume
Output voltage
Output voltage of heated oxygen
sensor (sensor 2: rear sensor)Mainly suspect
trouble area
OK
+25 %
-12.5 %
More than 0.5 V
Less than 0.4 V
Injection volume
Output voltage
+25 %
-12.5 %
More than 0.5 V
Less than 0.4 V
Injection volume
Output voltage
Sensor 1: front sensor
(sensor 1, heater, sensor 1
circuit)
+25 %
-12.5 %
More than 0.5 V
Less than 0.4 V
Injection volume
Output voltage
+25 %
-12.5 %
Injection volume
Output voltage
NG
+25 %
-12.5 %
Injection volume
Output voltage
NG
+25 %
-12.5 %
Injection volume
Output voltage
NG
+25 %
-12.5 %
Injection volume
Output voltage
NGExtremely rich or lean of the
actual air-fuel ratio
(Injector, fuel pressure, gas
leakage in exhaust system,
etc.) OK
OK
OK
Almost no reaction
Almost no reaction
'
Sensor 2: rear sensor
(sensor 2, heater, sensor 2
circuit)
Almost no reaction Almost no reaction
DI-1 10
- DIAGNOSTICSENGINE
303 Author: Date:
2004 LAND CRUISER (RM1071U)
NOTICE:
However, there is a few seconds delay in the sensor 1 (front sensor) output. And there is about 20
seconds delay in the sensor 2 (rear sensor).
The following A/F CONTROL procedure enables the technician to check and graph the voltage output of
the heated oxygen sensors (sensor 1 and 2).
For displaying the graph indication, enter ºACTIVE TEST / A/F CONTROL / USER DATAº then select ºO2S
B1S1 and O2S B1S2º by pressing ºYESº button and push ºENTERº button before pressing ºF4º button.
NOTICE:
If the vehicle is short of fuel, the air-fuel ratio becomes LEAN and heated oxygen sensor DTCs will
be recorded, and the MIL then comes on.
HINT:
If different DTCs related to different systems that have terminal E2 as the ground terminal are output
simultaneously, terminal E2 may be open.
Read freeze frame data using the hand-held tester or the OBD II scan tool. Freeze frame data records
the engine conditions when a malfunction is detected. When troubleshooting, it is useful for determin-
ing whether the vehicle was running or stopped, the engine was warmed up or not, the air-fuel ratio
was lean or rich, etc. at the time of the malfunction.
A high heated oxygen sensor (sensor 1) voltage (0.5 V or more) could be caused by a rich air fuel mix-
ture. Check for conditions that would cause the engine to run rich.
A low heated oxygen sensor (sensor 1) voltage (0.4 V or less) could be caused by a lean air fuel mix-
ture. Check for conditions that would cause the engine to run lean.
- DIAGNOSTICSENGINE
DI-1 11
304 Author: Date:
2004 LAND CRUISER (RM1071U)
1 Are there any other codes (besides DTC P0130, P0150, P2195, P2197, P2196 or
P2198) being output?
PREPARATION:
(a) Connect the hand-held tester or the OBD II scan tool to the DLC3.
(b) Turn the ignition switch ON and push the hand-held tester or OBD II scan tool main switch ON.
(c) When using hand-held tester, enter the following menus: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / CURRENT CODES.
CHECK:
Read the DTC using the hand-held tester or the OBD II scan tool.
RESULT:
Display (DTC Output)Proceed to
ºP0130, P0150, P2195, P2196, P2197 and/or P2198ºA
ºP0130, P0150 P2195, P2196, P2197 or P2198º and other DTCsB
HINT:
If any other codes besides ºP0130, P0150, P2195, P2196, P2197 and/or P2198º are output, perform the
troubleshooting for those DTCs first.
B Go to relevant DTC chart (See page DI-36).
A
+25 %
-12.5 %
More than 0.5 V
Less than 0.4 V
Case 1
Case 2
Case 3
Case 4
Output voltage of heated oxygen
sensor (sensor 1: front sensor)
Injection volume
Output voltage
Output voltage of heated oxygen
sensor (sensor 2: rear sensor)Mainly suspect
trouble area
OK
+25 %
-12.5 %
More than 0.5 V
Less than 0.4 V
Injection volume
Output voltage
+25 %
-12.5 %
More than 0.5 V
Less than 0.4 V
Injection volume
Output voltage
Sensor 1: front sensor
(sensor 1, heater, sensor 1
circuit)
+25 %
-12.5 %
More than 0.5 V
Less than 0.4 V
Injection volume
Output voltage
+25 %
-12.5 %
Injection volume
Output voltage
NG
+25 %
-12.5 %
Injection volume
Output voltage
NG
+25 %
-12.5 %
Injection volume
Output voltage
NG
+25 %
-12.5 %
Injection volume
Output voltage
NGExtremely rich or lean of the
actual air-fuel ratio
(Injector, fuel pressure, gas
leakage in exhaust system,
etc.) OK
OK
OK
Almost no reaction
'
Sensor 2: rear sensor
(sensor 2, heater, sensor 2
circuit)
Almost no reactionAlmost no reaction
Almost no reaction
DI-122
- DIAGNOSTICSENGINE
315 Author: Date:
2004 LAND CRUISER (RM1071U)
The following A/F CONTROL procedure enables the technician to check and graph the voltage output of
the heated oxygen sensors (sensor 1 and 2).
For displaying the graph indication, enter ºACTIVE TEST / A/F CONTROL / USER DATAº then select ºO2S
B1S1 and O2S B1S2º by pressing ºYESº button and push ºENTERº button before pressing ºF4º button.
NOTICE:
If the vehicle is short of fuel, the air-fuel ratio becomes LEAN and DTCs P0133 and/or P0153 will be
recorded, and the MIL then comes on.
If different DTCs related to different systems while terminal E2 as ground terminal are output simulta-
neously, terminal E2 may be open.
Read freeze frame data using the hand-held tester or the OBD II scan tool. Freeze frame data records
the engine conditions when a malfunction is detected. When troubleshooting, it is useful for determin-
ing whether the vehicle was running or stopped, the engine was warmed up or not, the air-fuel ratio
was lean or rich, etc. at the time of the malfunction.
A high heated oxygen sensor (sensor 1) voltage (0.5 V or more) could be caused by a rich air fuel mix-
ture. Check for conditions that would cause the engine to run rich.
A low heated oxygen sensor (sensor 1) voltage (0.4 V or less) could be caused by a lean air fuel mix-
ture. Check for conditions that would cause the engine to run lean.
- DIAGNOSTICSENGINE
DI-123
316 Author: Date:
2004 LAND CRUISER (RM1071U)
1 Are there any other codes (besides DTC P0133 or P0153) being output?
PREPARATION:
(a) Connect the hand-held tester or the OBD II scan tool to the DLC3.
(b) Turn the ignition switch ON and push the hand-held tester or OBD II scan tool main switch ON.
(c) When using hand-held tester, enter the following menus: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / CURRENT CODES.
CHECK:
Read the DTC using the hand-held tester or the OBD II scan tool.
RESULT:
Display (DTC Output)Proceed to
ºP0133 and/or P0153ºA
ºP0133 or P0153º and other DTCsB
HINT:
If any other codes besides ºP0133 and/or P0153º are output, perform the troubleshooting for those DTCs
first.
B Go to relevant DTC chart (See page DI-36).
A
DI-132
- DIAGNOSTICSENGINE
325 Author: Date:
2004 LAND CRUISER (RM1071U)
The following A/F CONTROL procedure enables the technician to check and graph the voltage output of
the heated oxygen sensors (sensor 1 and 2).
For displaying the graph indication, enter ºACTIVE TEST / A/F CONTROL / USER DATAº then select ºO2S
B1S1 and O2S B1S2º by pressing ºYESº button and push ºENTERº button before pressing ºF4º button.
HINT:
If different DTCs related to different systems terminal E2 as the ground terminal are output simulta-
neously, terminal E2 may be open.
Read freeze frame data using the hand-held tester or the OBD II scan tool. Freeze frame data records
the engine conditions when a malfunction is detected. When troubleshooting, it is useful for determin-
ing whether the vehicle was running or stopped, the engine was warmed up or not, the air-fuel ratio
was lean or rich, etc. at the time of the malfunction.
A high heated oxygen sensor (sensor 1) voltage (0.5 V or more) could be caused by a rich air fuel mix-
ture. Check for conditions that would cause the engine to run rich.
A low heated oxygen sensor (sensor 1) voltage (0.4 V or less) could be caused by a lean air fuel mix-
ture. Check for conditions that would cause the engine to run lean.
1 Are there any other codes (besides DTCs P0134 and P0154) being output?
PREPARATION:
(a) Connect the hand-held tester or the OBD II scan tool to the DLC3.
(b) Turn the ignition switch ON and push the hand-held tester or OBD II scan tool main switch ON.
(c) When using hand-held tester, enter the following menus: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / CURRENT CODES.
CHECK:
Read the DTC using the hand-held tester or the OBD II scan tool.
RESULT:
Display (DTC Output)Proceed to
ºP0134 and/or P0154ºA
ºP0134 or P0154º and other DTCsB
HINT:
If any other codes besides P0134 and/or P0154 are output, perform the troubleshooting for those codes first.
B Go to relevant DTC chart (See page DI-36).
A