1998 TOYOTA LAND CRUISER display

DI-366
- DIAGNOSTICSAUTOMATIC TRANSMISSION
559 Author
: Date
:
PATTERN SW (M)Pattern SW (PWR) Status/
ON or OFFPattern SW (PWR) is;
Pushed in: ON
Pushed once again: OFF
u
SNOW SWPattern SW (2nd) Status/
ON or OFF

IG SW ON: OFF
O

Pattern SW (2nd) Push: ON
O

Pattern SW (2nd) Push: OFF
u
SOLENOID (SLT)Shift Solenoid SLT Status/
ON or OFFIG SW ON: ONu
SOLENOID (SLU)Shift Solenoid SLU Status/
ON or OFF
Lock Up: ON

Except Lock Up: OFFu
SPD (SP2)
Counter Gear Speed display/
min.: 0 km/h (0 mph)
max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph)u
AT FLUID TEMP
ATF Temp. Sensor No. 1 Value/
min.: -40C (-40F)
max.: 215C (419F)80C (176F)
(After Stall Test)
If the value is º-40C (-40F)º or
º215C (419F)º, ATF temp. sen-
sor No. 1 circuit is opened or
shorted.
5. ACTIVE TEST
HINT:
Performing the ACTIVE TEST using the Hand-held tester allows the relay, VSV, actuator and so on to oper-
ate without parts removal. Performing the ACTIVE TEST as a first step of troubleshooting is one method
to shorten labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.
(a) Warm up the engine.
(b) Turn the ignition switch OFF.
(c) Connect the Hand-held tester to the DLC3.
(d) Turn the ignition switch ON.
(e) Push the ºONº button of Hand-held tester.
(f) Select the item º/DIAGNOSIS/ENHANCED OBD ll/ACTIVE TESTº.
(g) According to the display on tester, perform the ºACTIVE TESTº.
ItemTest DetailsDiagnostic Note
SHIFT
[Test Details]
Operate the shift solenoid valve and set the each shift position by your-
self.
[Vehicle Condition]
Less than 50 km/h (31 mph)
[Others]

Press " button: Shift up

Press u button: Shift downPossible to check the operation of
the shift solenoid values.
HINT:
Shifting to the 5th gear is possible
only when the vehicle stops or idle
is ON.
LOCK UP
[Test Details]
Control the shift solenoid SLU to set the ATM to the lock-up condition.
[Vehicle Condition]
Vehicle Speed: 58 km/h (36 mph) or more
Possible to check the SLU opera-
tion.
LINE PRESS UP
[Test Details]
Operate the shift solenoid SLT and raise the line pressure.
[Vehicle Condition]

Vehicle Stopped.

IDL: ON
[Others]
ON: Line pressure up.
OFF: No action (normal operation)
-

DI3BT-04
DI-396
- DIAGNOSTICSAUTOMATIC TRANSMISSION
589 Author
: Date
:
2004 LAND CRUISER (RM1071U)
PROBLEM SYMPTOMS TABLE
If a normal code is displayed during the diagnostic trouble code check although the trouble still occurs, check
the electrical circuits for each symptom in the order given in the charts on the following pages and proceed
to the page given for troubleshooting.
The Matrix Chart is divided into 3 chapters.
Chapter 1: Electronic Circuit Matrix Chart
Chapter 2: On-vehicle Repair Matrix Chart
Chapter 3: Off-vehicle Repair Matrix Chart
If the instruction ºProceed to next circuit inspection shown on matrix chartº is given in the flow chart
for each circuit, proceed to the circuit with the next highest number in the table to continue the check.
If the trouble still occurs even though there are no abnormalities in any of the other circuits, then check
and replace the ECM.
Chapter 1: Electronic Circuit Matrix Chart
HINT:
*1: When a malfunction is on the circuit *1 mark is attached, DTC is output.
SymptomSuspect AreaSee page
No up-shift
(A particular gear, from 1st to 4th gear, is not up-shifted)1. Shift solenoid valve (S1) circuit *1
2. Shift solenoid valve (S2) circuit *1
3. ECM
DI-460
DI-464
IN-36
No up-shift (4th " 5th)
1. Transmission control switch circuit (D - 4) *1
2. Engine coolant temp. sensor circuit *1
3. Speed sensor NT circuit *1
4. Shift solenoid valve (SL1) circuit *1
5. Shift solenoid valve (SL2) circuit *1
6. Shift solenoid valve (SR) circuit *1
7. ECM
DI-402
DI-36
DI-418
DI-426
DI-449
DI-468
IN-36
No up-shift (3rd " 4th)
1. Engine coolant temp. sensor circuit *1
2. Shift solenoid valve (S2) circuit *1
3. ECM
DI-36
DI-464
IN-36
No up-shift (1st " 2nd)
1. Transmission control switch circuit (2 - L) *1
2. Shift solenoid valve (S2) circuit *1
3. ECM
DI-402
DI-464
IN-36
No down-shift (5th " 4th)
1. Transmission control switch circuit (D - 4) *1
2. Shift solenoid valve (SL1) circuit *1
3. Shift solenoid valve (SL2) circuit *1
4. Shift solenoid valve (SR) circuit *1
5. ECM
DI-402
DI-426
DI-449
DI-468
IN-36
No down-shift (2nd " 1st)
1. Transmission control switch circuit (2 - L) *1
2. Shift solenoid valve (S2) circuit *1
3. ECM
DI-402
DI-464
IN-36
No down-shift
(A particular gear, from 1st to 4th gear, is not down-shifted)1. Shift solenoid valve (S1) circuit *1
2. Shift solenoid valve (S2) circuit *1
3. ECM
DI-460
DI-464
IN-36
No lock-up
1. ATF temperature sensor circuit *1
2. Transfer L4 position switch circuit *1
3. Stop light switch circuit *1
4. Speed sensor NT circuit *1
5. Shift solenoid valve (SLU) circuit *1
6. ECM
DI-410
DI-472
DI-424
DI-418
DI-491
IN-36
No lock-up offECMIN-36

- DIAGNOSTICSCRUISE CONTROL SYSTEM
DI-995
1188 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSPECTION PROCEDURE
HINT:
In case of using the hand-held tester, start the inspection from step 1 and in case of not using the hand-held
tester, start from step 2.
1 Check stop light switch using hand-held tester.
PREPARATION:
Connect the hand-held tester to the DLC3.
(a) Connect the hand-held tester to the DLC3.
(b) Turn the ignition switch ON and push the hand-held tester main SW ON.
CHECK:
Select the item ºSTOP LIGHT SWº in the DATA LIST and read its valve displayed.
OK:
Brake pedal depressed: ON
Brake pedal released: OFF
OK Proceed to next circuit inspection shown in
problem symptom table (See page DI-991).
NG
2 Check operation of stop light.
CHECK:
Check that stop light comes on when brake pedal is depressed, and turns off when brake pedal is released.
NG Check stop light system (See page BE-49).
OK

- DIAGNOSTICSCRUISE CONTROL SYSTEM
DI-1001
1194 Author
: Date
:
2004 LAND CRUISER (RM1071U)
CRUISE MAIN Indicator Light Circuit
CIRCUIT DESCRIPTION
When the cruise control main switch is turned ON, CRUISE MAIN indicator light lights up.
INSPECTION PROCEDURE
1 Perform Active Test of hand-held tester.
PREPARATION:
Connect the hand-held tester to the DLC3.
CHECK:
Check the cruise indicator of the combination meter using Active Test.
OK:
DescriptionTester displayCheck condition
CRUISE Indicator lightCRUISE INDICON/OFF
OK Proceed to next circuit inspection shown on
problem symptom table (See page DI-991).
NG
Check and replace combination meter.
(See page IN-36).
DIB6D-01

DI26U-32
DI-988
- DIAGNOSTICSCRUISE CONTROL SYSTEM
1181 Author
: Date
:
2004 LAND CRUISER (RM1071U)
DIAGNOSTIC TROUBLE CODE CHART
If a malfunction code is displayed during the DTC check, check the circuit listed for that code in the table
below and proceed to the appropriate page.
DTC No.
(See Page)Circuit InspectionTrouble Area
P0500/21
(DI-992)Vehicle Speed Sensor ºAº
Combination meter

Open or short in vehicle speed sensor circuit
P0503/23
(DI-992)Vehicle Speed Sensor ºAº Intermittent/Erratic/High

Oen or short in vehicle s eed sensor circuit

Vehicle speed sensor

ECM
P0571/52
(DI-993)Brake Switch ºAº Circuit

Short in stop light switch circuit

Stop light switch

ECM
P0607/54
(DI-997)Control Module Performance
ECM

DIB69-01
I24672
Hand-held tester
DLC3
A04550
DLC3
10 11 12 13 14 15 16 12345678
9
- DIAGNOSTICSCRUISE CONTROL SYSTEM
DI-981
1174 Author
: Date
:
2004 LAND CRUISER (RM1071U)
PRE-CHECK
1. DIAGNOSIS SYSTEM
(a) Description
ECM controls the function of cruise control on this vehicle.
Data of the cruise control or DTC can be read from DLC3
of the vehicle. When a trouble occurs on cruise control,
Check CRUISE MAIN indicator does not light up but DTC
inspection is performed.
Therefore when there seems to be a trouble on cruise
control, use hand-held tester or SST to check and trou-
bleshoot it.
(b) Check the DLC3.
The vehicle's ECM uses ISO 9141-2 for communication.
The terminal arrangement of DLC3 complies with SAE
J1962 and matches the ISO 9141-2 format.
Terminal No.Connection/Specified ConditionCondition
4Chassis Ground e Body Ground/1 or lessAlways
13TC e Body Ground/9 - 14 VAlways
HINT:
If your display shows ºUNABLE TO CONNECT TO VEHICLEº
when you have connected the cable of the hand-held tester to
DLC3, turned the ignition switch ON and operated the hand-
held tester, there is a problem on the vehicle side or tool side.

If communication is normal when the tool is connected to
another vehicle, inspect DLC3 on the original vehicle.

If communication is still not possible when the tool is con-
nected to another vehicle, the problem is probably in the
tool itself, so consult the Service Department listed in the
tool's instruction manual.

I24672
Hand-held tester
DLC3
- DIAGNOSTICSCRUISE CONTROL SYSTEM
DI-983
1176 Author
: Date
:
2004 LAND CRUISER (RM1071U)
2. USING HAND-HELD TESTER
(a) Hook up the hand-held tester to the DLC3.
(b) Monitor the ECU data by following the prompts on the tes-
ter screen.
HINT:
Hand-held tester has a ºSnapshotº function which records the
monitored data.
Please refer to the hand-held tester operator's manual for fur-
ther details.
3. DTC CLEARANCE
(a) The following actions will erase the DTCs and freeze
frame data.
(1) Operating the hand-held tester to erase the codes
(See the hand-held tester instruction book for oper-
ating instructions.).
(2) Disconnecting the battery terminals or EFI fuse.
(b) After completing repairs, the DTC retained in memory can
be cleared by removing the EFI fuse for 10 seconds or
more with the ignition switch off.
(c) Check that the normal code is displayed after connecting
the fuse.
4. DATA LIST
HINT:
According to the DATA LIST displayed by the hand-held tester,
you can read the value of the switch, sensor, actuator and so
on without parts removal. Reading the DATA LIST as a first step
of troubleshooting is one of the method to shorten the labor
time.
(a) Connect the hand-held tester to the DLC3.
(b) Turn the ignition switch ON.
(c) According to the display on tester, read the ºDATA LISTº.
ItemMeasurement Item/Display
(Range)Normal ConditionDiagnostic Note
VEHICLE SPD
Vehicle speed/
min.: 0 km/h (0 mph)max.: 255
km/h (158 mph)
Actual vehicle speed-
MEMORY SPD
Vehicle speed/
min.: 0 km/h (0 mph)max.: 255
km/h (158 mph)
Actual vehicle speed-
THROTTLE
Throttle operating angle/
min.: 0 km/h (0 mph)max.: 125
km/h ( mph)
Actual vehicle speed-
CRUISE CONTROLCruise controlON: Cruise control is SET
OFF: Cruise control is UNSET-
MAIN SW (MAIN)Main switch
(Main CPU)
ON: Main switch (Main CPU) is
SET
OFF: Main switch (Main CPU) is
UNSET
-

No.Operation MethodCRUISE Main Indicator Light
Blinking PatternDiagnosis
1 Turn -/SET switch ON
2Turn +/RES switch ON
3Turn CANCEL switch ON
Depress brake pedal
(Turn stop lamp switch assy ON)
Shift to except D position
(Turn PNP switch OFF)
LightON
OFFSwitch ON
Switch OFF
LightON
OFFSwitch OFF
Switch ON-/SET switch circuit
is normal
+/RES switch circuit
is normal
CANCEL switch circuit
is normal
Stop light switch circuit
is normal
PNP switch circuit is
normal
LightON
OFF LightON
OFF
0.5 sec.0.5 sec.
I24838
- DIAGNOSTICSCRUISE CONTROL SYSTEM
DI-987
1180 Author
: Date
:
2004 LAND CRUISER (RM1071U)
HINT:
When 2 or more signals are input to the ECM, the lowest num-
bered code will be displayed first.
7. INPUT SIGNAL CHECK
(Using hand-held tester)
(a) Connect the hand-held tester to DLC3.
(b) Check the control switch (MAIN, CANCEL, SET/COAST,
RES/ACC).