1998 NISSAN GT-R Service Manual

TROUBLE DIAGNOSES
Shift Mechanism
1 Turbine sensor 1
tine pressure solenoid I 1
Shift solenoid B
Full switch
ECM-TCM
(All side) (RB20DE, RB25DET) or TCM (RB25DE) p-
ECM.TCM (Engine side) * I
(RB20DE. RB25DET) or Venrle speed sensor 2
ECM (RB25DE) ,
1 (RB25DET)
POWER ~nd~calor lamp @AT;
( POWER (Except M-AT) ] 1 SNOW I
Shift control unit
(Except RB20DE)
Overdrive control switch
I
O/D OFF
indicator lamp
Steering shift main switch
- ATN 1983D

TROUBLE DIAGNOSES
Clutch and Band Chart
U0.C
(Low one-
way
clutchl L&R/B
(Low and
reverse
brake)
F/O C
(Forward
clutch)
.
Remarks
PARK POSI-
TION
REVERSE POSITION
O/C
(Overrun
clutch)
*I@
'I@
'18
@
NEUTRAL
POSITION
*"
c'utch)
0
0
WC
clutch)
(Reverse
0
P
R
N
Automatic shift
0
0
FIC
(For-
ward
clutch)
0
0
0
69
0
Band servo
'4
2 Automatic shift
1 st
2nd
-3rd 4th
1 st
1. Locked in 1st
-
4th apply
0
2nd apply
0
'263
*3@
2nd
I st
2nd
0
0
0
DUAL MATIC M-ATx
3rd release
0
8
0
0
0
--
fi In Band servo I FI0.C / UOC I L&WB I
(Reverse clutch) FIC (For- WC (High
ward
clutch) clutch)
PARK POSI-
TION
REVERSE POSITION
NEUTRAL POSITION
@ 0 . . Automatic shift
0 '269 8 - -
-38 8 0
@
G3 0 Automatic shift
10 I I Automatic shift
I I I I I I I
:ch is being set in "OFF position. (D, shift is inhibited.) '2: oil pressure is applied to both 2nd "apply" side and 3rd "releasen side of band servo piston. However, brake band does not contract because oil pressure area on the "releasen side is greater than that on the "apply" side. '3: Oil pressure is applied to 4th "apply" side in condition '2 above, and brake band contracts. '4: A/T will not shift to 4th when overdrive control switch is set in "OFF position.
* 1 : O~erate when control
swil
0: Operates. a: Operates
during "progressive" acceleration.
@: Operates but does not affect power transmission. @: Operates when throttle opening is less than specification, but does not affect engine brake. fi: O~erates when throttle opening is less than specification, activating engine brake.

TROUBLE DIAGNOSES
Component Parts Location
[M-AT (Except TCS)]
Control valve uppe:
Line pressure
solenoid Shift solenoid A
Shift solenoid B Overrun clutch
solenoid
Steering switch relay I Ql Shift control unit (Except RB20DE) ?
ATN 1 985D
AT-?

TROUBLE DIAGNOSES
Circuit Diagram
1 Data link connector for CONSULT
I I Vehicle speed sensor 1 I I (Output shaft speed sensor)
Turbine sensor (Exceot RB20DE)
Shifi CRI (M-AT)
65 10 Steering shifl SW (M-AT)
Steering shift main SW
1
Manual mode SW I
Terminal No. in parenthesis ( ) of throttle position sensor and throttle posit~on switch 1s used for RB25DET.
AT-8

TROUBLE DIAGNOSES
Circuit Diagram (Cont'd)
Data link connector for C0NS;ILT
Engine speed signal -
i? Throttle ~otal controi port&-2 s-2 33 7'' ELM I E - , 10
AT mode SW & '' 19
(2WD)
1- 1 I I Throttle msition sensor
I I Vehicle speed sensor 1
Turbine sensor 38 -
Throttle position SW 2 r I- 16
L TO IGN SW I PNPSW
To starter relay 4-1 34 - 27
A i 26
n I IGN IOA ID OFF 1ND.L AT> I T 22 I Shift CIU
ATN 1 987D

TROUBLE DIAGNOSES
Control Unit Input/Output Signal Specifications
Refer to EC section ("ECM.TCM or ECM Input/Output Signal
Reference Value").
USING CONSULT -
Monitor item Indication value Operating status
Throttle position sensor Approx.
0.4 - 4.OV
Throttle fully - closed to fully-open --
AK fluid temperature sensor I Appro~. 1.5 - 0.5V I A/T fluid: Appro~. 20 - 80°C -- - - --- -
ON Overdrive control switch: OFF
Lever switch
OFF Overdrive control switch: ON
Line pressure
duty 29 - 94% Low
pressure - High pressure
Lock-up duty
4 - 94% Lock-up released - Lock-up engaged
USING CIRCUIT TESTER
Terminal
No.' 1 Condition Specifications
.- Refer to EC section
("ECM-TCM or
5 (39) Engine speed signal - ECM Input/Output Signal Reference
Value*).
Voltage increases gradually in
Throttle position sensor
signal After
engine warm-up, depress accelerator pedal
slowly. response
to throttle position.
Fully-closed throttle
: Approx. 0.5V
Fully-open throttle : Approx. 4.2V
24 (I0) Power source
31 (19) Turn
ignition switch ON. Battery
voltage
Turn ignition switch OFF. Approx.
OV
--
25 (25) 1 Ground 32 (48) Turn ignition switch ON. Approx. OV
Shift control
signal SB1 - - 28 (I4) (Except RB20DE)
Vehicle speed sensor
2 When vehicle is moved at 2 to 3 km/h for more than Voltage varies approx. between OV 29 (40) (vehicle speed
signal in 1 m. and 4.5V intermittently.
speedometer)
*: Each number in parenthesis ( ) shows the terminal No. for TCM (RB25DE).

TROUBLE DIAGNOSES
Control Unit
InputlOutput Signal Specifications
Terminal
No.' Operation
or measurement condition Specifications
Idle switch
(in throttle position switch) After
engine warm-up, release accelerator pedal.
After engine warm-up, depress accelerator
pedal.
PNP switch "1"
position
(c > is used for M-AT.) Battery voltage
@ Approx.
OV
PNP switch
"2"
<"33 position
(c > is used for M-AT.) Selector lever:
"1"
&?"2 position
Selector lever;
Exce~t
"1"
<"2"> ~osition Battery voltage
gz
A~~rox.
OV
PNP switch
"Dm position Selector
lever:
2" <3*> position
Selector lever: Except
"Y 4'3'5 position
Selector lever;
"Dn
position Battery voltage
Approx. OV
Battery voltage
Neutral signal
(PNP switch
"N-P"
position)
- -- Selector lever: Except "Dm position Approx.
OV
PNP switch
"Rn
position RR Selector lever: "Nn, "P" position
Selector lever: Except
"N", "Pn position
Selector lever:
"Rn
~osition
I Selector lever: Except "Rn position 1 Approx. OV
U" " Approx. OV
Approx. 4.7V
. Batterv voltaae ST
I
After engine warm-up, depress accelerator pedal
partially. (Throttle opening: More than 50%) Battery voltage i% Full
switch
(in throttle position switch)
I After engine warm-up, release accelerator pedal. I Approx. OV
Sensor ground
Throttle position sensor
power -- -- - - - I
-- --- Turn iqnition switch ON. Ao~rox. OV @z!.
Shift control signal SB2
(Except RB20DE) Turn ignition switch
ON. Turn ignition switch
OFF.
Approx.
4.5 - 5.5V
Approx. OV
EL
Vehicle speed sensor 1
(Output shaft speed sensor) When vehicle
cruises at 30 kwh (Inspected in AC posi-
tion) More
than approx. 1 V
80
(Voltage increases in
resDonse to vehicle
meed.)
Turbine sensor (Except
RB20DE)
When vehicle parks (Inspected in AC position)
When turbine rotates at approx. 1,000
rpm I Approx. 0.1 V
Approx.
OV
rn fluid temperature sensor 5 I A/l fluid temperature: Approx. 20°C Approx. 1.5V
c
3 V) Battery voltage
Approx. OV .- Y .- c a, -
Afr mode switch (POWER)
(Except M-AT)
A/T fluid temperature: Approx. 80°C ,
AIT mode switch: POWER
A/T mode switch: Except POWER - - - - - - -- Shift control signal DB1
(Except RB20DE)
Shift control signal
DB3
(Except RB20DE) Approx. 0.5V
Overdrive control switch
(Except M-AT) Battery voltage
z g 0
Shift
control signal DB2
(Except RB20DE)
A/T mode switch (SNOW)
(Except TCS) Overdrive
control switch: ON (Contact: OFF)
- .= c .- & .&!
- 5
Stop lamp switch Overdrive
control switch:
OFF (Contact: ON)
CONSULT
(RX) signal Approx.
OV
Battery voltage Appro~. OV
Battery voltage
Approx. OV
.z w .- cJ=- T) .g
2
CONSULT (TX) signal
A/l mode switch: SNOW
A/l mode switch: Except SNOW
Depress brake pedal.
' Release brake pedal.
*: Each number in parenthesis ( ) shows the terminal No. for TCM (RB25DE).
AT-1 1

TROUBLE DIAGNOSES
Control Unit InputlOutput Signal Specifications
(Cont'd)
Terminal
No.' Operation
or measurement condition
Specifications
Total control signal
(multiple communication)
(Except
RB20DE) Refer to
EC section
("ECM.TCM or ECM Input1
Output Signal Reference Value").
I I
I Turn ignition swi?ch ON. I Battery voltage
Power supply (Backup)
Line pressure solenoid - - Turn ignition switch OFF. Battery voltage
r After engine
warm-up, depress accelerator pedal
Line pressure solenoid
(dropping resistor circuit) 5
Approx. OV
w
0.
s
Overrun clutch solenoid After engine
wan-up, release accelerator pedal.
After engine warm-up, release accelerator pedal.
After engine warm-up, depress accelerator pedal
fullv. .- >. .- 5
POWER indicator lamp (4AT)
Dual rnatic
AK waming lamp
(M-AT)
Approx. 1.5 - 3.OV
Approx. 4 - 14V
Approx. OV
When POWER indicator lamp is tumed on (W
mode switch: POWER), or dual matic warn-
ing lamp
is turned on
When
overrun clutch solenoid operates
When overrun clutch solenoid does not operate
Approx.
OV
Battery voltage Approx.
OV
When POWER indicator lamp is tumed off (NT
mode switch:Except POWER), or dual matic A/T Battery voltage
I warning lamp is turned off 1
I When vehicle is locked UD I Approx. 8 - 15V Lock-up solenoid I . .
When vehicle is not locked up I Approx. OV
When shift solenoid A operates
(Driving in 'Dln or
"D,")
When
shift solenoid A does not operate
(Driving in
"D," or "D,")
parenthesis
(
Battery voltage
Approx.
OV
Shift solenoid B
) shows the terminal No. for TCM (RB25DE ).
I
*: Each
When shift solenoid B operates
(Driving in 'Dln or
'D,")
When shift solenoid
B does not operate
(Driving in
"D,"
or
"Dd)
number Battery voltage
Approx. OV