1998 NISSAN GT-R Service Manual

TROUBLE DIAGNOSES
CONSULT (Cont'd)
DATA MONITOR MODE (M)
1 I Monitor item
I
tem Display ECU
input Main
signals
-
Description Remarks
signals
VHCUS
SE.A'T
[kmlh] or [mph]
I-
Vehicle speed computed from When
racing engine in "Nn or "P" signal of revolution sensor is position
with vehicle stationary,
displayed. CONSULT
data may not indicate
0 kmlh (0 mph).
Vehicle speed computed from Vehicle
speed display may not be
signal of vehicle speed sensor accurate under approx. 10 kmlh
is displayed. (6 mph). It may not indicate 0
kmlh (0 mph) when vehicle is sta-
tionary.
Throttle position sensor signal
voltage is displayed.
AlT fluid temperature sensor
signal voltage is displayed.
Signal voltage lowers as fluid
temperature rises.
Source voltage of TCM is dis-
played.
Engine speed, computed from Engine speed display
may not be
engine speed signal, is
dis- accurate under approx. 800 rpm.
played. It
may not indicate
0 rpm even
when engine is not running.
Turbine revolution computed Error
may occur under approx.
from signal of turbine revolution 800 rpm and will not indicate
0
sensor is displayed. rpm even if engine is not running.
ONIOFF state computed from
signal of overdrive control SW
is displayed.
ONIOFF state computed from
signal of PIN position SW is
displayed.
ONIOFF state computed from
signal of
R position SW is dis-
played.
ONIOFF state computed from
signal of D position SW is dis-
played.
ONIOFF status, computed from
signal of 2 position SW, is dis-
played.
signal of
1 position SW, is dis-
displayed. ASCD is mounted.
ON
... Cruising state
OFF ... Normal running state
Vehicle
speed sensor
1 (All) (Revolution sensor)
Vehicle speed sensor
2 (Meter) VHCUS SE,MTR
[kmk] or
[rnph]
Throttle position sensor
ITHRTLPOS SEN
I ,
AT fluid temperature sensor
PI
FLUID TEMP SE
Battery voltage
A
Engine speed ENGINE SPEED
[rpml
Turbine revolution sensor
TURBINE REV
[rpml
I
Overdrive control switch
OVERDRIVE SW
[ONIOFFJ
I
PIN position switch
PIN POSI SW
[ONlOFF]
R position switch
R POSITION SW
[OWOFF]
I
2 position switch
1
2 POSITION SW
[ONIOFF]
I
D position switch
1 position switch 1 POSITION SW
[ONIOFF]
I
D POSITION SW
[ON/OFF] X
ASCD OD cut signal
ASCD.OD CUT
[ONIOFF]
X
ASCD cruise signal
Status of ASCD OD release
signal is displayed.
ON
... OD released
OFF ... OD not released
ONIOFF status, computed from
signal of
kickdown SW, is dis-
played.
ONIOFF status, computed from
signal of HOLD shift SW, is dis-
played.
ONIOFF status, computed from
signal of closed throttle position
SW, is displayed.
ONIOFF status, computed from
signal of wide open throttle
position SW, is displayed.
ASCD.CRUISE
[ONIOFF]
This
is displayed even when no
ASCD is mounted.
This is displayed even when no
kickdown switch is equipped.
Kickdown
switch
KICKDOWN
SW
[ONIOFq
Wide open throttle position switch X .
X A/T mode switch
t
WIO THRUP-SW
[ONIOFq POWERSHIFT SW
[ONIOFF]
Closed
throttle position switch
, CLOSED THUSW
[ONIOFF]

TROUBLE
CONSU (Cont'd)
I Monitor item
Display input
signals Main
signals
-
Description Remarks
Indicates check signal (reen-
trant signal) status for TCM
control signal output.
ONIOFF
status of shift solenoid is not
changed when thermal insula-
tion or short-circuit occurs in
these valves.
Shift solenoid A SHlFT
SN A
Shift solenoid
B [ONIOFF]
OVRRUNIC SN
- [ONOFF]
Overrun
clutch solenoid
OVRRUN/C SN2
- [ONIOFF]
HOLD SW
[ONIOFFI
X
MANU MODE SW
[ONIOFFJ
NONM MODESW
[ONIOFF]
UP SW
[ONOFF]
X
DOWN SW
[ON/OFFl X
NON SHlFT SW - [ONlOFF]
Overrun
clutch solenoid
2 (Excep
RB20DE)
HOLD!SNOW
switch
A/T mode switch - SNOW mode
1 Gate side contact in mznual
mode switch
Manual
mode switch (Except
RB20DE)
- Non-gate side contact in
manual mode switch
UP (+) side contact in manual
mode switch
Non-manual
mode switch (Excepi
RB20DE)
UP switch (Except
RB20DE)
DOWN (-) side contact in
manual mode switch
DOWN
switch (Except
RB20DE)
Non-shift switch (Except
RB20DE)
Brake switch
I Stop lamp switch
BRAKE SW
[OWOFF] I
Shift solenoid A pressure detec-
tion switch
Gear position data used for
computation by TCM, is dis-
played.
Selector lever position data, A specific value used for control
used for computation by TCM, is
displayed if fail-safe is
acti-
is displayed. vated
due to error.
Vehicle speed data, used for
computation by TCM, is dis-
played.
- -- Shift solenoid valve A (P switch)
(Except
RB20DE) SHlFT
SN A
Gear position
- --- - - Selector lever position SLCT
LVR POSl
I -
VEHICLE
SPEED
[kmlh] or [mph]
I -
Vehicle speed
THROTTLE POSl
Throttle position data, used for A specific value used for control
computation by TCM, is
dis- is displayed if fail-safe is acti-
played. vated due to error.
Throttle
position
- - Control value of line pressure
solenoid valve, computed by
TCM from each input signal, is
displayed.
Control value of torque con-
verter clutch solenoid valve,
computed by TCM from each
input signal, is displayed.
Line
pressure duty LINE
PRES
DTY I
-- Torque converter clutch soienoid
valve duty TCC
SN DUTY I
Shift solenoid valve A .-control value of shift solenoid Control value
of solenoid is dis-
valve A, computed by TCM played even
if solenoid circuit is
from each input signal, is
dis- disconnected.
. - played. The
"OFF signal is displayed if
Control value of shift solenoid solenoid circuit is shorted.
Shift solenoid valve El SHIFT SN B I valve 6, computed by TCM
from each input signal, is dis-
played.
Control value of overrun clutch
solenoid valve computed by
TCM from each input signal is I OVERRUNIC SN I Overrun clutch solenoid valve
displayed.
D Control status of TCM power
>OWER
SFT
LMP
Power shift lamp
shift lamp
-- - Voltage
- Pulse
X: Applicable
-: Not applicable

TROUBLE DIAGNOSES
Self-diagnosis
DESCRIPTION
If malfunction should occur in electrical systems, turning ignition switch ON lights M mode switch POWER
indicator lamp
(M-AT Dual matic AfT warning lamp) for 2 seconds, and then flashes the indicator lamp for 8 Gc
seconds. If malfunction does not occur, A/T mode switch POWER indicator lamp (M-AT Dual matic A/T warn-
ing lamp) is turned on for
2 seconds upon turning ignition switch ON. To locate and display the malfunction-
ing part, output the trouble information memory and flash
A/T mode switch POWER indicator lamp (M-AT Dual
matic
A/T warning lamp) by inputting self-diagnostic startup signal.
SELF-DIAGNOSIS PROCEDURE
1. Warm up engine.
2. Repeat ON-OFF cycles of ignition switch for more than once, and turn it OFF at last.
3. Move A/T mode switch to AUTO, and turn overdrive control switch to O/D ON.
4. Turn ignition switch ON with selector lever in "Pn position, and ensure POWER indicator lamp is turned on
for
2 seconds.
5. Turn ignition switch OFF.
6. Move selector lever to "D" position.
7. Turn overdrive control switch O/D OFF.
8. Turn ignition switch ON.
9. Move selector lever to "2" position.
10. Turn overdrive control switch OID ON.
11. Move selector lever to "I" position.
12. Turn overdrive control switch O/D OFF.
13. Depress accelerator pedal fully, and release it.
14. Read flashing status of POWER indicator lamp to complete self-diagnosis procedures.
M-AT
1. Warm up engine.
2. Repeat ON-OFF cycles of ignition switch for more than once, and turn it OFF at last.
3. Turn ignition switch ON with selector lever in "P" position, and ensure dual matic PJT warning lamp is turned
on for
2 seconds.
4. Turn ignition switch OFF.
5. Depress brake pedal, release accelerator pedal, and then move selector lever to "D" position.
6. Turn ignition switch ON.
7. Release brake pedal, and move selector lever to "3" position.
8. While depressing brake pedal with left foot, depress accelerator pedal fully with right foot, and move
selector lever to
"2" position.
9. Read dual matic A/T warning lamp indication to complete self-diagnosis procedures.

TROUBLE DIAGNOSES
Self-diagnosis (Cont'd)
\ I1 // \ 11 // =-I= or =mj= // 11 \ // 11 \
1, = 2.5 sec. t, = 2.0 sec. t, = 1.0 sec.
RB20DE 10 judgement flashes.
Stan signal Malfunctioning unit and circuit I
Except RBPODE 13 judgement flashes.
signal Malfunctioning unit and circuit I
POWER INDICATOR LAMP OR DUAL MATIC A/T
WARNING LAMP INDICATION
If malfunction occurs in electrical system, indicator lamp stays on
longer at corresponding circuit.
Flashing
order
t5 1 Overrun clutch solenoid
1
2
3
4
5
7 1 Lock-up solenoid
Malfunctioning
unit and circuit
Vehicle speed sensor
1
Vehicle speed sensor 2
Throttle position sensor
Shift solenoid
A
Shift solenoid B
I
W fluid temperature sensor, TCM power supply, or throttle posi-
tion sensor power supply
RB20DE
9 1 Engine speed
signal Except
RB20DE
10 1 Line
pressure solenoid I Turbine sensor
I - I Line pressure solenoid
12 1 - I Total control signal
When indicator lamp repeats flashing in 4 Hz, the following malfunctions
may exist: (Insufficient memory backup
powerflCM repiacement1Battery
has been disconnected for prolonged
periodllow battery power)
13
No flashes
HOW TO ERASE SELF-DIAGNOSTIC RESULTS
To facilitate cause investigation of malfunction that is less likely to
reappear, the TCM always stores self-diagnostic results during cus-
tomer operation. This memory cannot be erased even if ignition
switch
is turned ON and OFF repeatedly. To erase the seif-diag-
nostic
results, turn ignition switch
OFF after self-diagnosis has
been performed, or use
"ERASE" function of CONSULT.
- - - - Shift control unit
PNP switch, idle
switch/full switch
Overdrive control switch Stop lamp switch

TROUBLE DIAGNOSES
Symptom Chart
Sharp shock in Engine brake
applied
Shifting
Malfunctions
Slip
(Racing)
hifting
.- erator pedal
Shifting
Shifting
inspection item
Fluid level and status
Control linkage
PNP switch (short/open circuit)
Throttle ~osition sensor (installed)
I Vehicle weed sensor
I Enaine meed sensor
A/T fluid temperature sensor
Engine idle speed
Line
Dressure
Control valve assembly
Shift solenoid
A
Shift solenoid B
Line pressure solenoid
Lock-up solenoid
Overrun clutch solenoid
Accumulator N-D
Accumulator
1-2
Accumulator 2-3
Accumulator 3-4 (N-R) Ignition coil and starter motor
Overdrive control switch
I AfT mode switch (AUTO)
Torque converter
1 Oil pump
I Reverse clutch
I High clutch
I Forward clutch
I Forward one-wav clutch
I Overrun ciutch
1 Low one-wav clutch
I Low reverse brake
Brake. band (including servo)
Parking linkage

Symptom Chart (Cont'd)
Greater noise
Malfunctions
Inspection item No shifting
I Shifting I
Fluid level
and status 11
Control linkage
-
(I) C 0 .- c. .- (I) 0 a
v
-CU
n - 1
PNP switch
(shortlopen
circuit)
Throttle position sensor (installed)
2 2
Vehicle speed sensor
I Engine speed sensor -
-T
L o 1 Control valve assembly .- - -- Shift solenoid A 4 3
. ' Shift solenoid 6 4 cut I1
--, Line pressure solenoid .- 5 -t Lock-up solenoid ?
6 Overrun clutch solenoid 3
Accumulator N-D
1 Accumulator 1-2 I 1-
Accumulator 2-3
Accumulator 3-4 (N-R)
Ignition coil and starter motor
I Overdrive control switch I 1-
A/T mode switch (AUTO)
A/T mode switch (POWER) I - I Ail mode switch (SNOW) I
I Torque converter I I
1 Oil pump I I -- - - Reverse clutch 0 -
'g High clutch a 4 6
%I Forward clutch I I - .- a Forward one-way clutch -
$ Overrun clutch a, 8
Low one-way clutch
O Low reverse brake 7
Brake band (including servo) 7
Parking linkage

TROUBLE DIAGNOSES
Symptom Chart (Cont'd)
xi - - ([I C V) a, C .- cn C W
t 0 .- .L 2 a, - 8 0 ([I L 0 0 Q
& 0 a, a, Q V)
5 E .- X
i! L a
zl -I - 1 -
- 2 -
-
-
-
-
-
5 - 3 - 4 -
-
-
-
-
-
-
-
-
-
-
-
-
I1 - 0 - 6 - 7 -
-
-
-
-
9 - 8 -
-
vj c 0 .- - .- V) 0 n
Q 7J C ([I
t C .- r ([I c. V) c. 0 C V) a 0 7J 0, C .- 0 C W -
- 2 - 3 -
-
- -
-
1 -
-
-
-
- - a +- ([I a a, 2 0 c. 0 C V) a, 0 u a, - 0 2
8 - 1 -
-
-
-
-
-
-
-
2 - 3 -
-
-
-
-
-
-
-
-
-
-
- I
i
g
- 4 -
-
-
-
-
-
-
B- ; 2 to a =? - 0,
2 5.j c 2.z 2 a0 - 0- z & 5 0 gE V) V)o C 02 .s nu 5 ng %-([I C O c --t .- V) a V) r aa ([I z gz a, a- c 50 -6 s
6 $2
11
2
I
I
Malfunctions
Inspection item
I I I Fluid level and status I I Control linkage 2
PNP switch (shortfopen circuit) 1 I I I Throttle position sensor (installed) 111213
Vehicle speed sensor
214
Engine speed sensor L -
AIT fluid temperature sensor
Engine idle weed
Line pressure
Control valve assembly
Shift solenoid A 3
3
Shift solenoid B 4 4
Line pressure solenoid
Lock-up solenoid
Overrun clutch solenoid
u I I I -
Accumulator N-D I I 1 I Accumulator 1-2
Accumulator 2-3 I Accumulator 3-4 (N-R)
Ignition coil and starter motor
Overdrive control switch
Torque converter
tg Reverse clutch .- High clutch
2 Forward clutch C .- a Forward one-way clutch -.
$ Overrun clutch 0, 8
? Low one-way clutch 3= O Low reverse brake 9
Brake band (including servo)
Parking linkage

BRAKE SYSTEM
SECTION B R
CONTENTS
ANTI-LOCK BRAKE SYSTEM ........................................ 2
Fail-safe Function ........................................................ 2
System Diagram .......................................................... 2
Circuit Diagram ............................................................ 3
Component Parts Location .......................................... 4
Control Unit Input/Output Signal Specifications .......... 5
Precautions for Trouble Diagnosis ..... ......................... 7
Basic Inspection ........................................................... 7
CONSULT
.................................................................... 8
Self-diagnosis ...... .. . .. .. .... . . .. . . .. .. .. . . . ..... . .. . . .... .. .. . . ... .. . . -14
TCSIABS SYSTEM ........................................................ 17
System Description.
.. ............................... .................. 17
System Diagram
..................... . .................................. 1 8
Component Parts Location ........................................ 19
Circuit Diagram .......................................................... 20
Control Unit InpuVOutput Signal Specifications .. ...... 21
Precautions for Trouble Diagnosis
............................ 26
Basic Inspection.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -26
CONSULT for TCS/ABS Control Unit Control
System
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -27
Self-diagnosis for TCSfABS Control Unit Control
System
. . . . . . . . . . .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . -34
CONSULT for Throttle Control Unit Control
System
. ... ... . .... . . . .. . . . .. . ... . . ... . .. . . . . . . .. . . . ... ... . . .. . . .. . . . .. . . . . .. -37
Self-diagnosis for Throttle Control Unit Control
System
. .. . . . . . . .. ... . .. . . . .. .. .. . . . . . . .. .. . . . ... . . . . . . . .. . . .. . . .. . . . . . . ... . . -41