1997 SSANGYONG KORANDO engine oil

1B2 -- 16 M161 ENGINE MECHANICAL
D AEW OO M Y_2000
Operation When Full- Load at Partial Load
1 HFM Sensor
2 Cylinder Head Cover
3 Oil Spearation Chamber (Full-- Load or Over
Mid-- Load)
4 Intake Air Duct (Cross Pipe)
5 Vent Line (Full-- Load or Over Mid-- Load)
6 Throttle Valve
7 Restrictor, Diameter 1.1mm
(Mid-- Load at Idling)
8 Intake Manifold
9 Vent Line (Mid-- Load at Idling)
10 Air Conditioner Bracket11 Oil Separation Chamber (Mid-- Load at Idling)
12 Crank Chamber
13 Oil Return Pipe
14 Oil Pan
15 Timing Gear Case Cover
16 Crankcase
17 Chain Housing
A Fresh Air
CBlow--byGas
D Vent Connection

M161 ENGINE MECHANICAL 1B2 -- 17
D AEW OO M Y_2000
Operation When Full- Load at Partial Load
DThe throttle valve (6) is partially opened or fully
opened.
The air flows very rapidly through the vent line (5) s
connection (D) and the intake air duct when full-- load
at partial load.
Consequently, most of the low-- by gases are supplied
to the combustion chamber through the timing gear
case cover (15), chain housing (17), oil separation
chamber (3), vent line (5), throttle valve (6), and in-
take manifold (8).

M161 ENGINE MECHANICAL 1B2 -- 27
D AEW OO M Y_2000
Removal & Installation Procedure
1. Remove the intake air duct.
Installation Notice
Tightening Torque
9--11NSm (80 -- 97 lb-in)
2. Remove the spark plug cover.
Installation Notice
Tightening Torque
9--11NSm (80 -- 97 lb-in)
Notice:Release 3 screws from the spark plug cover and
remove the cover for M161 Engine coil.
3. Remove the spark plug connector and ignition cable.
4. Unscrew the bolts (3) and remove the head cover and
the gasket.
Installation Notice
Tightening Torque
9--11NSm (80 -- 97 lb-in)
Notice:Replace the gasket with a new one if necessary.
5. Installation should follow the removal procedure in
the reverse order.
6. Check for oil leaks by operating the engine.

1B2 -- 34 M161 ENGINE MECHANICAL
D AEW OO M Y_2000
TIMING GEAR CASE COVER
Preceding Work: Removal of viscous clutch
Removal of cylinder head front cover
Removal of tensioning device
Removal of water pump
Removal of oil filter element
Removal of oil pan
Removal of generator bracket
1 Bolt (M8 X 60, 3 pieces)
22.5-- 27.5 NSm (16.6-- 20.3 lb-ft) .............
2 Bolt (M8 X 75, 1 piece)
22.5-- 27.5 NSm (16.6-- 20.3 lb-ft) .............3Seal
4 Timing gear case cover
5O--ring
6 Sleeve

M161 ENGINE MECHANICAL 1B2 -- 35
D AEW OO M Y_2000
Tools Required
116 589 20 33 00 Sliding Hammer
116 589 01 34 00 Threaded Pin
Removal & Installation Procedure
1. Remove the power steering belt pulley and A/C com-
pressor bracket.
2. Remove the oil line from power steering pump.
3. Rotate the crankshaft so that the piston of number,
cylinder is at ATDC20°.
4. Put the alignment marks (arrows) on the timing chain
and camshaft sprocket.
5. Remove the chain tensioner.
Installation Notice
Tightening Torque
72 -- 88 NSm (53 -- 65 lb-ft)
6. Remove the intake and exhaust camshaft sprocket
(remove the camshaft adjuster assembly in E23 en-
gine).
Installation Notice
Ti
ghteningTo rque
1st step: 18 -- 22 NSm
(13 -- 16 lb-ft)
TighteningTorque
2nd step: 60°±5°
Notice:The flange bolt is designed to be used only
once, so always replace with new one.
7. Remove the guide rail pin using the sliding hammer
116 589 20 33 00 (02) and the threaded pin 116 589
01 34 00 (03).
Notice:Apply the sealant on guide rail pin when installa-
tion.

1B2 -- 36 M161 ENGINE MECHANICAL
D AEW OO M Y_2000
8. Unscrew the bolts (A).
Installation Notice
Tightening Torque
22.5 -- 27.5 NSm
(16.6 -- 20.3 lb-ft)
9. Remove the belt pulley and vibration damper.
Installation Notice (Center Bolt)
Ti
ghteningTo rque
1st step: 200 + 20NSm
(148 + 15 lb-ft)
TighteningTorque
2nd step: 90°+10°
10. Unscrew the bolts (1, 2) on timing gear case cover
and remove the timing gear case cover.
Installation Notice
Tightening Torque
22.5 -- 27.5 NSm
(16.6 -- 20.3 lb-ft)
Notice:Be careful not to damage the cylinder head gas-
ket.
11. Remove the radial shaft seal.
Notice:Installation note replace the seal with new one.
12. Clean the timing gear case cover and crankcase
sealing surface.
13. Replace the O -- ring with new one and apply the
sealant on the sealing surface.
Notice:Be careful not to stain the oil chamber of chain
tensioner with the sealant.
14. Installation should follow the removal precedure in
the reverse order.
15. Warm up the engine and check for oil leaks.

1B2 -- 38 M161 ENGINE MECHANICAL
D AEW OO M Y_2000
Tools Required
601 589 03 43 00 Crankshaft Rear Seal Installer
Removal & Installation Procedure
1. Unscrew the bolts (1) and (5) and remove the closing
cover by pulling the rear cover lug (arrows).
Notice:Be careful not to damage the oil pan gasket.
2. Clean the sealing surface of the crankcase and the
rear sealing cover.
3. Check the radial shaft seal and replace it if necessary.
4. Apply the Loctite 573 to the rear cover sealing sur-
face.
5. Apply the engine oil to the dust lip of the radial shaft
seal.
Notice:Do not use the grease.
6. Install the crankshaft rear radial seal and the crank-
shaft sealing rear cover, using crankshaft rear seal in-
staller 601 589 03 43 00.
7. Install the crankshaft sealing rear cover mounting
bolts and remove the crankshaft rear seal installer
601 589 03 43 00.
Installation Notice
Tightening Torque
9--11NSm (80 -- 97 lb-in)
8. Installation should follow the removal procedure in
the reverse order.

1B2 -- 40 M161 ENGINE MECHANICAL
D AEW OO M Y_2000
Components
1 Center Bolt (M18 x 50)
2 Center Bolt Washer
3 Vibration Damper and Pulley Assembly
4Key
5 Crankshaft Front Seal
6 Timing Gear Case Cover7 Crankshaft Sprocket (Camshaft Driven)
8 Crankshaft Sprocket (Oil pump Driven)
9 Crankshaft
10 Oil Pan
11 Oil Pan Gasket
12 Oil Pan Mounting Bolt (M6 x 22)
ServiceDataStandard
Permissble Deviation of The Vibration DamperRadial Runout0.6 mmp
Axial Runout0.6 mm