1997 SSANGYONG KORANDO child seat

SECTION 8A
SEAT BELTS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation...................................8A-2
Driver Seat Belt Warning......................................8A-2
Three-Point Front Seat Belt With Pretensioner.......8A-2
Three-Point Rear Outboard Seat Belt....................8A-2
Two-Point Lap Rear Center Seat Belt....................8A-2
Operational and Functional Checks......................8A-2
Child Seat Tether Anchor.....................................8A-2
Component Locator.............................................8A-3
Front Seat Belt.....................................................8A-3
Rear Seat Belt.....................................................8A-4Repair Procedures...............................................8A-5
On-Vehicle Service.................................................8A-5
Three-Point Front Seat Belt With Pretensioner.......8A-5
Front Seat Belt Height Adjuster............................8A-6
Three-Point Rear Outboard Seat Belt....................8A-6
Two-Point Lap Rear Center Seat Belt....................8A-7
Child Seat Tether Anchor.....................................8A-7
Specifications.......................................................8A-8
Fastener Tightening Specifications.......................8A-8
Schematic and Routing Diagrams.......................8A-9
Seat Belt & Tension Reducer...............................8A-9

SSANGYONG MY2002
8A-2 SEAT BELTS
DESCRIPTION AND OPERATION
DRIVER SEAT BELT WARNING
The driver’s seat belt incorporates a seat belt warning
lamp in the instrument cluster to remind the driver if
the seat belt is not fastened when the ignition is turned
ON. The warning lamp blinks for eight seconds with
chime and goes out.
THREE-POINT FRONT SEAT BELT
WITH PRETENSIONER
The front seat belt contains an electronically controlled
pyrotechnic retractor, pretensioner, which reduces seat
belt slack when it activated in a head-on or angled
front collision. The front seat belt must be replaced
after an accident that causes its activation. At normal
condition the driver’s seat belt operates as emergency
locking retractor (ELR).
Emergency Locking Retractor (ELR)
The ELR seat belt is always unlocked, allowing the
passenger freedom of movement, except in
emergencies such as rapid deceleration, rapid
acceleration, or hard cornering maneuvers.
THREE-POINT REAR OUTBOARD
SEAT BELT
The rear outboard seating position uses the emergency
locking retractor (ELR). Refer to Three-point front seat
belt with pretensioner in this section for details.
TWO-POINT LAP REAR CENTER
SEAT BELT
The two-point lap rear center seat belt is a single contin-
uous length of webbing. The webbing is routed from
the anchor through plate and into a single retractor.
OPERATIONAL AND FUNCTIONAL
CHECKS
Caution:
Keep sharp objects and potentially damaged ob
jects away from seat belts.
Avoid bending or damaging any portion of
buckle or the latch plate
Do not breach or dye the belt webbing. Use only
mild soap and water in order to clean the belts.
When installing the seat belt anchor bolts and
screws, start the bolts and screws by hand in or-
der to prevent cross-threading.
Do not attempt any repairs on the retractor mech-
anisms or covers. Replace any defective assem-
blies with new assemblies.
Replace any belts that are cut or damaged in any
way.
1. Inspect all seat anchor bolts and screws in order to
verify that they are secure.
2. Inspect the seat belt buckle. The buckle must lock
and unlock easily.
3. After inserting the latch into the buckle, tug sharply
on the belt. The buckle must remain locked.
4. Fully extend the shoulder belt portion to make sure
that there is no twisting or tears in the belt.
5. Let the shoulder belt retract fully. The belt should
retract easily.
CHILD SEAT TETHER ANCHOR
There are three child seat tether anchors to hold the
child seat firmly. One is located rear center of ceiling
and two are located on the rear corner of floor.

SEAT BELTS 8A-7
SSANGYONG MY2002


yyyy yyyy
yyyy
KAA8A090
KAA8A100
KAA8A110
KAA8A080
3. Remove the lower quarter trim panel. Refer to Sec-
tion 9G Interior Trim.
4. Remove the bolt, screw and seat belt retractor.
Installation Notice
5. Remove the plastic cap to reveal the bolt.
6. Remove the upper anchor bolt.
Installation Notice
7. Installation should follow the removal procedure
in the reverse order.
TWO-POINT LAP REAR CENTER
SEAT BELT
Removal and installation Procedure
1. Fold the rear seat cushion.
2. Remove the bolts and the seat belt anchors.
Installation Notice
3. Installation should follow the removal procedure
in the reverse order.
CHILD SEAT TETHER ANCHOR
Removal and installation Procedure
1. Open the tether anchor access cap if equipped.
2. Remove the bolt and the tether anchor.
Installation Notice
3. Installation should follow the removal procedure
in the reverse order.
Tightening TorqueBolt 45 Nm (33 lb-ft)
Tightening TorqueBolt 45 Nm (33 lb-ft)
Tightening TorqueBolt 45 Nm (33 lb-ft)
Tightening TorqueBolt 19 Nm (14 lb-ft)

SSANGYONG MY2002
8A-8 SEAT BELTS
N•m
19
45
45
45Lb-Ft
14
33
33
33 Child Seat Tether Anchor Bolt
Seat Belt Anchor Bolt
Seat Belt Height Adjuster Bolt
Seat Belt Retractor BoltLb-In
-
-
-
-Application
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS

INTERIOR TRIM 9G-7
SSANGYONG MY2002
KAA9G140
KAA9G130
FLOOR CONSOLE
Removal and Installation Procedure
1. Remove the screws.
2. Remove the floor console.
3. Disconnect the electrical connector.
4. Installation should follow the removal procedure
in the reverse order.
FRONT ROCKER TRIM PANEL
Removal and Installation Procedure
1. Remove the screws.
2. Remove the rocker trim panel.
3. Installation should follow the removal procedure
in the reverse order.
KAA9G160
KAA9G150
6. Remove the luggage hook with the mounting
screws.
7. Remove the front seat. Refer to Section 9H, Seats.
FLOOR CARPET
Removal and Installation Procedure
1. Disconnect the negative battery cable.
2. Remove the rear seat. Refer to Section 9H, Seats.
3. Remove the bolts and the left and the right lower
seat belt anchors.
4. Remove the child seat anchor. Refer to Section
9H, Seats.
5. Remove the floor carpet screws.

SECTION 9H
SEATS
TABLE OF CONTENTS
Components Locator............................................9H-2
Seats ...................................................................9H-2
Repair Instructions................................................9H-3
On-Vehicle Service Unit Repair................................9H-3
Front Seat............................................................9H-3
Front Seat Cushion..............................................9H-3
Front Seatback....................................................9H-4
Front Seat Guide Rail ...........................................9H-4
Front Seat Recliner Lever.....................................9H-5
Front Seat Trim....................................................9H-5
Head Restraint.....................................................9H-5Walk In Device....................................................9H-6
Front Seat Armrest...............................................9H-6
Rear Seat Armrest ...............................................9H-6
Rear Seat............................................................9H-7
50/50 Split Rear Seat Cushion Hinge....................9H-7
50/50 Split Rear Seat Cushion Lock Striker...........9H-8
Child Seat Anchorage ..........................................9H-8
Specifications.......................................................9H-9
Fastener Tightening Specifications.......................9H-9
Schematic and Routing Diagram......................9H-10
Seat Heater.......................................................9H-10

SSANGYONG MY2002
9H-8 SEATS
50/50 SPLIT REAR SEAT CUSHION
LOCK STRIKER
Removal and Installation Procedure
1. Remove the bolts and rear seat cushion lock
striker.
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
2. Installation should follow the removal procedure
in the reverse order.
KAA9H200
2. Remove the child seat anchorage bolt.
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
3. Installation should follow the removal procedure
in the reverse order.
KAA9H190
CHILD SEAT ANCHORAGE
Removal and Installation Procedure
1. Remove the child seat anchorage cover.
Tightening Torque34.3 - 53.9 Nm
(25 - 39 lb-ft)
KAA9H170
Tightening Torque 19 Nm (14 lb-ft)

SEATS 9H-9
SSANGYONG MY2002
-
-
-
-
-
-
-
-
-
- 14
12 - 18
14.5 - 23.2
13 - 18
14.5 - 23.2
14.5 - 23.2
25 - 39
25 - 39
25 - 41
12 - 18Lb-In
Lb-Ft
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Child Seat Anchorage Bolt
Front Armrest Mounting Bolt
Front Seat Bolts
Guide Rail Bolts
Rear Seat Bolts (Lift Up)
Rear Seat Bolts (Front)
Rear Seat Cushion Hinge Bolts
Rear Seat Cushion Lock Striker Bolts
Seat Back Bolts
Seat Cushion BoltsApplication
N•m19
16.7 - 25.5
19.6 - 31.4
17.6 - 25.5
19.6 - 31.4
19.6 - 31.4
34.3 - 53.9
34.3 - 53.9
34.3 - 55.9
16.7 - 25.5