1997 SSANGYONG KORANDO child lock

SSANGYONG MY2002
8A-2 SEAT BELTS
DESCRIPTION AND OPERATION
DRIVER SEAT BELT WARNING
The driver’s seat belt incorporates a seat belt warning
lamp in the instrument cluster to remind the driver if
the seat belt is not fastened when the ignition is turned
ON. The warning lamp blinks for eight seconds with
chime and goes out.
THREE-POINT FRONT SEAT BELT
WITH PRETENSIONER
The front seat belt contains an electronically controlled
pyrotechnic retractor, pretensioner, which reduces seat
belt slack when it activated in a head-on or angled
front collision. The front seat belt must be replaced
after an accident that causes its activation. At normal
condition the driver’s seat belt operates as emergency
locking retractor (ELR).
Emergency Locking Retractor (ELR)
The ELR seat belt is always unlocked, allowing the
passenger freedom of movement, except in
emergencies such as rapid deceleration, rapid
acceleration, or hard cornering maneuvers.
THREE-POINT REAR OUTBOARD
SEAT BELT
The rear outboard seating position uses the emergency
locking retractor (ELR). Refer to Three-point front seat
belt with pretensioner in this section for details.
TWO-POINT LAP REAR CENTER
SEAT BELT
The two-point lap rear center seat belt is a single contin-
uous length of webbing. The webbing is routed from
the anchor through plate and into a single retractor.
OPERATIONAL AND FUNCTIONAL
CHECKS
Caution:
Keep sharp objects and potentially damaged ob
jects away from seat belts.
Avoid bending or damaging any portion of
buckle or the latch plate
Do not breach or dye the belt webbing. Use only
mild soap and water in order to clean the belts.
When installing the seat belt anchor bolts and
screws, start the bolts and screws by hand in or-
der to prevent cross-threading.
Do not attempt any repairs on the retractor mech-
anisms or covers. Replace any defective assem-
blies with new assemblies.
Replace any belts that are cut or damaged in any
way.
1. Inspect all seat anchor bolts and screws in order to
verify that they are secure.
2. Inspect the seat belt buckle. The buckle must lock
and unlock easily.
3. After inserting the latch into the buckle, tug sharply
on the belt. The buckle must remain locked.
4. Fully extend the shoulder belt portion to make sure
that there is no twisting or tears in the belt.
5. Let the shoulder belt retract fully. The belt should
retract easily.
CHILD SEAT TETHER ANCHOR
There are three child seat tether anchors to hold the
child seat firmly. One is located rear center of ceiling
and two are located on the rear corner of floor.

SECTION 9H
SEATS
TABLE OF CONTENTS
Components Locator............................................9H-2
Seats ...................................................................9H-2
Repair Instructions................................................9H-3
On-Vehicle Service Unit Repair................................9H-3
Front Seat............................................................9H-3
Front Seat Cushion..............................................9H-3
Front Seatback....................................................9H-4
Front Seat Guide Rail ...........................................9H-4
Front Seat Recliner Lever.....................................9H-5
Front Seat Trim....................................................9H-5
Head Restraint.....................................................9H-5Walk In Device....................................................9H-6
Front Seat Armrest...............................................9H-6
Rear Seat Armrest ...............................................9H-6
Rear Seat............................................................9H-7
50/50 Split Rear Seat Cushion Hinge....................9H-7
50/50 Split Rear Seat Cushion Lock Striker...........9H-8
Child Seat Anchorage ..........................................9H-8
Specifications.......................................................9H-9
Fastener Tightening Specifications.......................9H-9
Schematic and Routing Diagram......................9H-10
Seat Heater.......................................................9H-10

SSANGYONG MY2002
9H-8 SEATS
50/50 SPLIT REAR SEAT CUSHION
LOCK STRIKER
Removal and Installation Procedure
1. Remove the bolts and rear seat cushion lock
striker.
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
2. Installation should follow the removal procedure
in the reverse order.
KAA9H200
2. Remove the child seat anchorage bolt.
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
3. Installation should follow the removal procedure
in the reverse order.
KAA9H190
CHILD SEAT ANCHORAGE
Removal and Installation Procedure
1. Remove the child seat anchorage cover.
Tightening Torque34.3 - 53.9 Nm
(25 - 39 lb-ft)
KAA9H170
Tightening Torque 19 Nm (14 lb-ft)

SEATS 9H-9
SSANGYONG MY2002
-
-
-
-
-
-
-
-
-
- 14
12 - 18
14.5 - 23.2
13 - 18
14.5 - 23.2
14.5 - 23.2
25 - 39
25 - 39
25 - 41
12 - 18Lb-In
Lb-Ft
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Child Seat Anchorage Bolt
Front Armrest Mounting Bolt
Front Seat Bolts
Guide Rail Bolts
Rear Seat Bolts (Lift Up)
Rear Seat Bolts (Front)
Rear Seat Cushion Hinge Bolts
Rear Seat Cushion Lock Striker Bolts
Seat Back Bolts
Seat Cushion BoltsApplication
N•m19
16.7 - 25.5
19.6 - 31.4
17.6 - 25.5
19.6 - 31.4
19.6 - 31.4
34.3 - 53.9
34.3 - 53.9
34.3 - 55.9
16.7 - 25.5