1997 SSANGYONG KORANDO drain bolt

M162 ENGINE MECHANICAL 1B1 -- 3
D AEW OO M Y_2000
FASTENER TIGHTENING SPECIFICATIONS (Cont’d)
ApplicationNSmLb-FtLb-In
Exhaust Mainfold Nut to Stud Bolt26 -- 3419 -- 25--
Oil Drain Plug2518--
Oil Filter Cover2518--
Oil Filter Bolt2518--
Oil Pump Drive Sprocket Bolt29 -- 3521 -- 26--
Oil Pump Mounting Bolt22.5 -- 27.516.6 -- 20.3--
Oil Strainer Bracket Bolt9--11--89 -- 97
Oil Pressure Relief Valve Screw Plug5037--
Oil Dipstick Guide Tube Bolt9--11--89 -- 97
Oil Gallery Screw Plug1511--
Torque Converter Mounting Bolts4231--
Crankshaft Bearing Cap Bolts55/+90°41/+90°--
Oil Pan Mounting BoltsM82518--g
M610--89

1B1 -- 8 M162 ENGINE MECHANICAL
D AEW OO M Y_2000
Removal & Installation Procedure
1. Disconnect the negative terminal of battery.
2. Remove the hood.
3. Remove the under cover.
Installation Notice
Tightening Torque
28 -- 47 NSm (21 -- 35 lb-ft)
4. Disconnect the mass air flow sensor meter connec-
tor.
5. Disconnect the mass air flow sensor meter from the
air filter housing.
6. Remove the intake air duct mounting nuts.
Installation Notice
Tightening Torque
9--11NSm (80 -- 97 lb-in)
7. Remove the air cleaner cover. Remove the mounting
bolts and air cleaner housing and element assembly.
8. Loosen the radiator drain cock and drain the coolant.
Notice:Open the coolant reservoir cap.

M162 ENGINE MECHANICAL 1B1 -- 9
D AEW OO M Y_2000
9. Loosen the cylinder block drain plug and then drain
the coolant completely.
Installation Notice
Tightening Torque
30 NSm (22 lb-ft)
Notice:Replace the seal before installation of the drain
plug.
10. Remove the cooling fan shroud. Refer toSection
1D1, Engine Cooling.
11. Disconnect the each hose from radiator.
12. Remove the upper mounting bolts of radiator and
then remove the radiator.

M162 ENGINE MECHANICAL 1B1 -- 29
D AEW OO M Y_2000
Tools Required
617589001000 AllenWrenchSocket
116 589 01 34 00 Threaded Pin
116 589 20 33 00 Sliding Hammer
Removal & Installation Procedure
1. Rotate the crankshaft so that the piston of number 1
cylinder is at TDC.
Notice:Rotate the crankshaft in the normal engine di-
rection.
2. Put the alignment marks (arrows) on the timing chain
and camshaft sprocket.
3. Drain the coolant from the crankcase.
4. Remove the three flange bolts in the exhaust cam-
shaft sprocket.
Installation Notice
Ti
ghteningTo rque
1st step: 18 -- 22 NSm
(13 -- 16 lb-ft)
TighteningTorque
2nd step: 60°±5°
Do not reuse the removed bolts.
5. Separate the chain from the camshaft sprocket.
Notice:Be careful not to drop the chain into the timing
case.
6. Remove the guide rail fixing pin using threaded pin
116 589 01 34 00 (1) and sliding hammer 116 589 33
00 (2).

1B1 -- 88 M162 ENGINE MECHANICAL
D AEW OO M Y_2000
OIL PAN
Preceding Work: Removal of front stabilizer
Removal of steering gear box
1 Gasket Replace...........................
2 Bolt (M6 x 22, 6 pieces) 10 NSm (89 lb-in) .....
3 Drain Plug (M6 x 20) 25 NSm (18 lb-ft) .......
4 Bolt (M6 x 20, 22 pieces) 10 NSm (89 lb-in) ....5 Bolt (M6 x 85) 10 NSm (89 lb-in) .............
6 Bolt (M8 x 40) 25 NSm (18 lb-ft) .............
7 Bolt (M10) 40 NSm (30 lb-ft) .................
8OilPan
Removal & Installation Procedure
1. Remove the drain plug and drain the oil completely.
2. Unscrew the bolts and remove the oil pan and gasket.
Notice:Arrange the bolts according to each size.
3. Clean the inside of oil pan and sealing surface, then
apply the sealant.
4. Replace the gasket with new one.
5. Install the oil pan with gasket, and tighten each bolt in
specified torque.
6. Check for oil leaks while running the engine.

1B1 -- 90 M162 ENGINE MECHANICAL
D AEW OO M Y_2000
ENGINE OIL AND OIL FILTER
ELEMENT
Tools Required
103 589 02 09 00 Oil Filter Remover
Replacement Procedure
1. Install the oil filter remover 103 589 02 09 00 on the oil
filter cover.
Notice:Make the screw cover removable by tightening
the bolt at the side of the oil filter remover 103 589 02 09
00.
2. Install the wrench to the upper bolt in the oil filter re-
mover 103 589 02 09 00 and remove the oil cover by
turning it.
3. Remove the oil filter element.
Notice:Work with a cloth under the vehicle when re-
moving the oil filter element not to drain the oil.
4. Remove the drain plug (arrow) and drain the engine
oil.
Notice:Leave the oil filler cap open to ease theengine
oil discharge.
5. Tighten the engine oil drain plug after cleaning it.
Installation Notice
Tightening Torque
25 NSm (18 lb-ft)
Replace the seal washer with new one.
6. Replace the O -- ring in the oil filter cover with new one.
Notice:Apply the engine oil to the O -- ring.
7. Insert new oil filter element into the oil filter housing.

M162 ENGINE MECHANICAL 1B1 -- 93
D AEW OO M Y_2000
Removal & Installation Procedure
1. Drain the coolant from the crank case.
2. Remove the each coolant line and hose.
3. Remove the oil filter bolt and then remove the oil filter.
Installation Notice
Tightening Torque
25 NSm (18 lb-ft)
Notice:Replace the oil filter gasket.
4. Installation should follow the removal procedure in
the reverse order.
5. Check engine oil level.
6. Run the engine at idle and check the engine for leaks.

1D1 -- 2 M162 ENGINE COOLING
D AEW OO M Y_2000
SPECIFICATIONS
GENERAL SPECIFICATIONS
ApplicationDescription
Cooling TypeWater Cooling Forced Circulation
RadiatorCirculation TypeDouble Cross Flow
Radiation Capability70,000 kcal/h
Dimension(Width x Height x Thickeness)580 x 482 x 45 mm
Cooling Fanφ460, Six Blades
Anti-- Freeze AgentALUTEC -- P78
Mixing Ratio of Anti-- Freeze Agen with Water (Anti-- Freeze Agent : Water)50 : 50
Coolant Capacity11. 3 L
Reservoir Capacity3.4 L
Cap Operating Pressure (Reservoir Tank Pressure Cap)1.4 bar
FASTENER TIGHTENING SPECIFICATIONS
ApplicationNSmLb-FtLb-In
Coolant Drain Plug3022--
Engine Hanger Bracket and Coolant Outlet
Port Bolt22.5 -- 27.516.6 -- 20.3--
Thermostat Cover Bracket Bolts9--11--80 -- 97
Oil Cooler Pipe Line Bolts9--11--80 -- 97
Cooling Fan Bolts9--11--80 -- 97
Viscous Clutch Mounting Bolts40.5 -- 49.529.8 -- 36.5--
Automatic Transmission Fluid Cooler Pipe2015--
Cooling Fan Shroud Bolts3--7--27 -- 62
Automatic Transmission Radiator Tube
Assembly Mounting Bolt7--62
Radiator Bracket Mounting Bolts3--7--27 -- 62