1996 TOYOTA TERCEL torque

LU-16
- LUBRICATIONOIL PUMP
1996 TERCEL (RM440U)
(a) Place a new gasket on the exhaust pipe.
(b) Connect the exhaust pipe to the exhaust manifold with 2
compresson springs and 2 bolts.
Torque: 62 N´m (630 kgf´cm, 46 ft´lbf)
6. w/ A/C:
INSTALL A/C COMPRESSOR AND MOUNTING
BRACKET
(a) Install the compressor mounting bracket with the 4 bolts.
Torque: 27 N´m (270 kgf´cm, 20 ft´lbf)
(b) Install the A/C compressor to the bracket with the 4 bolts.
Torque: 25 N´m (250 kgf´cm, 18 ft´lbf)
(c) Connect the A/C compressor connector.
7. INSTALL CRANKSHAFT TIMING PULLEY (See page
EM-17)
8. INSTALL TIMING BELT (See page EM-17)
9. INSTALL OIL DIPSTICK
10. FILL WITH ENGINE OIL
11. START ENGINE AND CHECK FOR LEAKS
12. CHECK ENGINE OIL LEVEL
13. INSTALL HOOD

S06257
16 mm Plug Wrench
IG0152
P20433
P20584
- IGNITIONIGNITION SYSTEM
IG-3
634 Author
: Date
:
1996 TERCEL (RM440U)
3. INSPECT SPARK PLUGS
(a) Disconnect high-tension cords from spark plugs.
(b) Using a 16 mm plug wrench, remove the spark plug.
(c) Using a spark plug cleaner or wire brush, clean the spark
plug.
If the electrode has traces of wet carbon, allow it to dry and then
clean with a spark plug cleaner.
Air pressure:
Below 588 kPa (6 kgf/cm
2, 85 psi)
Duration: 20 seconds or less
HINT:
If there are traces of oil, remove it with gasoline before using the
spark plug cleaner.
(d) Visually checkthe spark plug for thread damage and insu-
lator damage.
If abnormal, replace the spark plug.
Recommended spark plug:
DENSOK16TR11
NGKBKR5EKB11
(e) Inspect the electrode gap.
Correct electrode gap: 1.1 mm (0.043 in.)
(f) Using a 16 mm plug wrench, remove the spark plug.
Torque: 18 N´m (180 kgf´cm, 13 ft´lbf)
(g) Reconnect the high-tension cords from the ignition coils.

IG08G-03
S06147
- IGNITIONIGNITION COIL
IG-7
1996 TERCEL (RM440U)
REMOVAL
1. DISCONNECT HIGH-TENSION CORDS FROM IGNI-
TION COILS (See page IG-1)
2. REMOVE IGNITION COILS
(a) Disconnect the 2 connectors from the ignition coils.
(b) Remove the 2 bolts and 2 ignition coils from cylinder
head.
Torque: 8.5 N´m (85 kgf´cm, 70 in.´lbf)
HINT:
Arrange the ignition coils in correct order.

IG08J-01
IG-10
- IGNITIONCAMSHAFT POSITION SENSOR
1996 TERCEL (RM440U)
REMOVAL
REMOVE CAMSHAFT POSITION SENSOR
(a) Disconnect the camshaft position sensor connector.
(b) Remove the bolt and camshaft position sensor.
Torque: 8 N´m (80 kgf´cm, 69 in.´lbf)

IG08M-04
P21254
Connector Clamp
P21034
- IGNITIONCRANKSHAFT POSITION SENSOR
IG-13
1996 TERCEL (RM440U)
REMOVAL
1. DISCONNECT CRANKSHAFT POSITION SENSOR
CONNECTOR AND CLAMP
2. REMOVE RH ENGINE UNDER COVER
3. REMOVE NO.2 TIMING BELT COVER (See page
EM-12)
4. REMOVE CRANKSHAFT POSITION SENSOR
Remove the bolt and disconnect the crankshaft position sensor.
Torque: 8 N´m (80 kgf´cm, 69 in.´lbf)

ST0IX-01
P25750
P25751
P25783
Cutout
Protrusion
P25753
ST0941
(2)
(4)(3)
(1) ST-4
- STARTINGSTARTER (Reduction Type)
1996 TERCEL (RM440U)
DISASSEMBLY
1. REMOVE FIELD FRAME AND ARMATURE
(a) Remove the nut, and disconnect the lead wire from the
magnetic switch terminal.
Torque: 5.9 N´m (60 kgf´cm, 52 in.´lbf)
(b) Remove the 2 through bolts.
Torque: 9.3 N´m (95 kgf´cm, 82 in.´lbf)
(c) Pull out the field frame together with the armature.
HINT:
Align the protrusion of the field frame with the grove of the mag-
netic switch.
2. REMOVE STARTER HOUSING, CLUTCH ASSEMBLY
AND GEAR
(a) Remove the 2 screws.
Torque: 9.3 N´m (95 kgf´cm, 82 in.´lbf)
(b) Remove these parts from the magnetic switch:
(1) Starter housing
(2) Idler gear and bearing
(3) Clutch assembly
(4) Return spring
HINT:
Insert the return spring in to the magnetic switch hole.

ST0009
Magnet
P25752
ST0198
- STARTINGSTARTER (Reduction Type)
ST-5
1996 TERCEL (RM440U)
3. REMOVE STEEL BALL
Using a magnetic finger, remove the steel ball from the clutch
shaft hole.
4. REMOVE BRUSHES AND BRUSH HOLDER
(a) Remove the 2 screws and end cover from the field frame.
Torque: 1.5 N´m (15 kgf´cm, 13 in.´lbf)
(b) Using a screwdriver, hold the spring back and disconnect
the brush from the brush holder. Disconnect the 4
brushes, and remove the brush holder.
NOTICE:
Check that the positive (+) lead wire are not grounded.
5. REMOVE ARMATURE FROM FIELD FRAME

P25608
Wooden
Block
40 mm
37 mm
20 mmContact
Plate
V06796
P25609
SST
P25479
- STARTINGSTARTER (Reduction Type)
ST-1 1
1996 TERCEL (RM440U)
(f) Temporarily tighten the terminal nuts.
(g) Tighten the terminal nut.
(1) Put a wood block on the contact plate and press it
down with a hand press.
Dimensions of wood block:
20 x 37 x 40 mm (0.97 x 1.46 x 1.57 in.)
Press force:
981 N (100 kgf, 221 lbf)
NOTICE:

Check the diameter of the hand press ram. Then cal-
culate the gauge pressure of the press when 981 N
(100 kgf, 221 lbf) of force is applied.

If the contact plate is not pressed down with the spe-
cified pressure, the contact plate may tilt due to coil
deformation or the tightening of the nut.
(2) Using SST, tighten the nut to the specified torque.
SST 09810-38140
Torque: 17 N´m (173 kgf´cm, 12 ft´lbf)
NOTICE:
If the nut is over tightened, it may cause cracks on the in-
side of the insulator.
(h) Clean the contact surfaces of the contact plate and plung-
er.
Clean the contact surfaces of the remaining contact plate
and plunger with a dry shop rag.
(i) Reinstall the magnetic switch end cover.
Install the plunger, new gasket, end cover and lead clamp
with 3 bolts.
Torque: 3.6 N´m (36 kgf´cm, 32 in.´lbf)