Page 46 of 1202
P21589
SA3501
Grease
RA0489
MA-8
- MAINTENANCECHASSIS
46 Author: Date:
1996 TERCEL (RM440U)
(b) Check the dust cover for damage.
6. CHECK TRANSAXLE OIL (FLUID)
Visually check the transaxle for oil (fluid) leakage.
If leakage is found, check for the cause and repair.
7. REPLACE TRANSAXLE OIL (FLUID)
(a) M/T:
Replace the transaxle oil (See page MX-6).
(b) A/T:
Replace the transaxle fluid.
(A132L: See page AX-2)
(A242L: See page AX-2)
8. REPACK REAR WHEEL BEARINGS
(a) Change rear wheel bearing grease.
(1) Remove the hub and inner and outer bearings.
Clean in solvent and inspect the bearings for dam-
age.
(2) Pack the bearings and axle hubs with multipurpose
grease.
Wheel bearing grease grade:
Lithium base multipurpose grease (NLGI No.2)
(b) Install inner bearing and new oil seal.
(c) Install the hub and adjust the wheel bearing preload (See
page SA-42).
Preload (while turning):
Add frictional force plus
0 - 11.8 N (0 - 1.2 kgf, 0 - 2.6 lbf)
Page 54 of 1202
PP18T-03
- PREPARATIONENGINE MECHANICAL
PP-7
1996 TERCEL (RM440U)
SSM (Special Service Materials)
08826-00080Seal Packing Black or equivalent
(FIPG)Camshaft bearing cap (No. 1 and
No. 2)
Cylinder head cover
Rear oil seal retainer
08826-00100Seal Packing 1282B,
THREE BOND 1282B or equivalent
(FIPG)Water outlet housing
08833-00070Adhesive 1324,
THREE BOND 1324 or equivalentSpark plug tube
Flywheel or drive plate bolt
08833-00080Adhesive 1344
THREE BOND 1344
LOCTITE 242 or equivalentOil pressure switch
Page 138 of 1202
SS0N6-04
SS-8
- SERVICE SPECIFICATIONSENGINE MECHANICAL
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Cylinder head cover x Cylinder head7.07061 in.´lbf
No. 2 idler pulley x Cylinder head2828020
Camshaft timing pulley x Camshaft5151037
No. 1 idler pulley x Cylinder block18.518513
Crankshaft pulley x Crankshaft1551,55011 2
No. 2 crankshaft pulley x Crankshaft pulley1919514
RH engine mounting insulator x RH engine mounting bracket6465047
RH engine mounting insulator x Body7374054
No. 1 engine hanger x Cylinder head2121015
No. 2 engine hanger x Cylinder head5353038
Cylinder head x Cylinder block 1st
2nd45
Turn 90°450
Turn 90°33
Turn 90°
Camshaft bearing cap x Cylinder head131309
Intake manifold x Cylinder head19.519514
Intake manifold stay x Intake manifold2020015
Intake manifold stay x Cylinder block2020015
Exhaust manifold x Cylinder head4848035
Exhaust manifold stay x Cylinder block4040029
Exhaust manifold stay x Exhaust manifold4040029
Exhaust manifold heat insulator x Exhaust manifold8.08069 in.´lbf
Water outlet housing x Cylinder head3030022
Camshaft position sensor x Cylinder head8.08069 in.´lbf
EGR VSV x Cylinder head17.517513
EGR valve x Cylinder head17.517513
EGR pipe x EGR valve4040029
EGR pipe x Intake manifold3030022
PS ump bracket x Cylinder head4344032
Fuel inlet hose x Fuel filter2930022
Front exhaust pipe x Exhaust manifold6263049
Connecting rod cap x Connecting rod4040029
Crankshaft bearing cap x Cylinder block5858042
Rear oil seal retainer x Cylinder block7.57565 in.´lbf
Oil filter union x Cylinder block2525018
Oil pressure switch x Cylinder block131309
RH engine mounting bracket x Cylinder block5959043
Knock sensor x Cylinder block4545033
Generator bracket x Cylinder block2424018
Rear end plate x Cylinder block101007
Flywheel x Crankshaft9090065
Drive plate x Crankshaft9090065
Drive plate x Torque converter clutch2525018
A/C compressor bracket x Cylinder block2728020
PS pump adjusting strut x Cylinder block2121015
Page 162 of 1202
SS0LO-07
SS-32
- SERVICE SPECIFICATIONSSUSPENSION AND AXLE
162 Author: Date:
1996 TERCEL (RM440U)
SUSPENSION AND AXLE
SERVICE DATA
Cold tire inflationTire sizeCold tire inflation
pressure
Tire size
155SR13 ASFront240 kPa (2.4 kgf/cm2, 34 psi)ressure 155SR13 AS Front
Rear
240 kPa (2.4 kgf/cm, 34 si)
225 kPa (2.25 kgf/cm2, 32 psi)
Vehicle heightTire size
155SR13 ASFront
Rear
187.9 mm (7.40 in.)
253.2 mm (9.97 in.)
Front wheel align-
mentToe-in (Total)
Tie rod end left-right error0.1° ± 0.2° (1 ± 2 mm, 0.04 ± 0.08 in.)
1.5 mm (0.059 in.) or less
ment
Camber
Left-right error-0°20' ± 45'
45' or less
Caster
Left-right error1°20' ± 45'
45' or less
Steering axis inclination
Left-right error12°10' ± 45'
45' or less
Wheel angle Inside wheel
Outside wheel35°55' ± 2°
32°10' (Reference)
Rear wheel align-Toe-in (Total)0.3° ± 0.3° (3 ± 3 mm, 0.12 ± 0.12 in.)Rear wheel align-
ment
Camber
Left-right error-0°30' ± 45'
45' or less
Front axleAxle bearing backlash0.05 mm (0.0020 in.) or lessFront axle
Axle hub deviation0.05 mm (0.0020 in.) or less
Front suspensionLower ball joint turning torque0.8 - 2.5 N´m (8 - 25 kgf´cm, 7 - 22 in.´lbf)
Rear axleBearing preload (turning)Add frictional force plus 0 - 11.8 N (0 - 1.2 kgf, 0 - 2.6 lbf)Rear axle
Axle hub axial play0.05 mm (0.0020 in.) or less
Page 167 of 1202
SS0N2-05
- SERVICE SPECIFICATIONSSTEERING
SS-37
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
STEERING COLUMN
Steering support x Column tube5.45548 in.´lbf
Control valve shaft x Sliding yoke2526019
Steering main shaft x Sliding yoke2526019
Steering column assembly set nut2526019
Steering wheel set nut3435025
Steering wheel pad set screw8.89078 in.´lbf
PS VANE PUMP
Pressure port union x Front housing6970051
Suction port union x Front housing131309
Pressure feed tube x Pressure port union5455040
PS vane pump pulley set nut4344032
PS vane pump assembly set nut Bolt A4344032 PS vane um assembly set nut Bolt A
Bolt B
43
39
440
400
32
30
MANUAL STEERING GEAR
Pinion bearing adjusting screw lock nut for use with SST
for use without SST85
11 3871
1,15063
83
Rack guide spring cap lock nut for use with SST
for use without SST41
56419
57530
42
Rack x Rack end for use with SST
for use without SST43
59434
60031
43
Tie rod end lock nut4748035
Manual steering gear bracket x Body5859043
Pinion shaft x Sliding yoke2526019
Steering main shaft x Sliding yoke2526019
Column hole cover x Body4.95043 in.´lbf
PS GEAR
Cylinder end stopper5960043
Self-locking nut5960043
Rack housing cap5960043
Rack guide spring cap lock nut for use with SST
for use without SST31
44316
45023
33
Rack x Rack end for use with SST
for use without SST43
59434
60031
43
Tie rod end lock nut4748035
Turn pressure tube union nut for use with SST
for use without SST20
25203
25015
18
Air control valve2930022
PS gear bracket x Body5859043
Engine rear mount insulator Bolt A6465047 Engine rear mount insulator Bolt A
Bolt B
64
78
650
800
47
58
Engine rear mount bracket x Transaxle4849035
Front exhaust pipe x Exhaust manifold6263046
Front exhaust pipe clamp1919014
Front exhaust pipe x Oxygen sensor4445032
Page 818 of 1202
SA10Z-04
- SUSPENSION AND AXLETROUBLESHOOTING
SA-1
817 Author: Date:
1996 TERCEL (RM440U)
TROUBLESHOOTING
PROBLEM SYMPTOMS TABLE
Use the table to help you find the cause of the problem. The numbers indicate the priority of the likely case
of the problem. Check each part in order. If necessary, replace these parts.
SymptomSuspect AreaSee page
Wander/pulls
1. Tire (Worn or improperly inflated)
2. Wheel alignment (Incorrect)
3. Steering linkage (Loosen or worn)
4. Hub bearings (Worn)
5. Steering gear (Out of adjustment or broken)
6. Suspension parts (Worn)SA-2
SA-4
SA-8
-
SA-10
SA-39
SR-34
SR-46
-
Bottoming
1. Vehicle (Overloaded)
2. Spring (Weak)
3. Shock absorber (Worn)-
SA-24
SA-44
SA-24
SA-44
Sways/pitches
1. Tire (Worn or improperly inflated)
2. Stabilizer bar (Rear axle beam)
3. Shock absorber (Worn)SA-2
SA-54
SA-24
SA-44
Front wheel shimmy
1. Tire (Worn or improperly inflated)
2. Wheels (Out of balance)
3. Shock absorber (Worn)
4. Wheel alignment (Incorrect)
5. Ball joint (Worn)
6. Hub bearing (Worn)
7. Steering linkage (Loosen or worn)
8. Steering gear (Out of adjustment or broken)SA-2
SA-2
SA-24
SA-4
SA-34
SA-10
-
SR-34
SR-46
Abnormal tire wear
1. Tire (Worn or improperly inflated)
2. Wheel alignment (Incorrect)
3. Suspension parts (Worn)
4. Shock absorber (Worn)SA-2
SA-4
SA-8
-
SA-24
SA-44
Page 820 of 1202
R11682
- SUSPENSION AND AXLETIRE AND WHEEL
SA-3
819 Author: Date:
1996 TERCEL (RM440U)
4. CHECK WHEEL BEARING LOOSENESS
(a) Check the backlash in bearing shaft direction.
Maximum: 0.05 mm (0.0020 in.)
(b) Check the axle hub deviation.
Maximum: 0.05 mm (0.0020 in.)
5. CHECK FRONT SUSPENSION FOR LOOSENESS
6. CHECK STEERING LINKAGE FOR LOOSENESS
7. CHECK BALL JOINT FOR LOOSENESS
8. CHECK SHOCK ABSORBER WORKS PROPERLY
Check for oil leaks
Check mounting bushings for wear
Bounce front and rear of the vehicle
