1996 TOYOTA TERCEL torque

P20175
New
Gasket
FI1654
Fulcrum Length
SST
30 cm
FI4295
CORRECT
WRONG
WRONG Delivery Pipe O-Ring
Grommet
Injector
FI4296
Delivery
Pipe
O-Ring
Grommet
InjectorCylinder Head
- MFIMFI SYSTEM
MF-3
527 Author
: Date
:
1996 TERCEL (RM440U)
(b) When connecting the union bolt on the high pressure pipe
union, observe these procedures:
(1) Always use 2 new gaskets.
(2) Tighten the union bolt by hand.
(3) Tighten the union bolt to the specified torque.
Torque: 29.0 N´m (290 kgf´cm, 22 ft´lbf)
(c) When connecting the flare nut on the high pressure pipe
union, observe these procedures:
(1) Apply a light coat of engine oil to the flare nut, and
tighten the flare nut by hand.
(2) Using SST, tighten the flare nut to specified torque.
SST 09631-22020
NOTICE:
Do not rotate the fuel pipe, when tightening the flare nut.
Torque: 30 N´m (300 kgf´cm, 23 ft´lbf)
HINT:
Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
(d) Observe these precautions when removing and installing
the injectors.
(1) Never reuse the O-ring.
(2) When placing a new O-ring on the injector, take
care not to damage it in any way.
(3) Coat a new O-ring with spindle oil or gasoline be-
fore installing-never use engine, gear or brake oil.
(e) Install the injector in the delivery pipe and cylinder head
as shown in the illustration.

P20392
SST
MF-6
- MFIFUEL PUMP
530 Author
: Date
:
1996 TERCEL (RM440U)
(d) Install the fuel inlet hose and SST (pressure gauge) to the
fuel filter outlet with the 3 gaskets and union bolt.
SST 09268-45012
Torque: 29.0 N´m (290 kgf´cm, 22 ft´lbf)
(e) Wipe off any splattered gasoline.
(f) Reconnect the negative (-) terminal cable to the battery.
(g) Connect the TOYOTA hand-held tester to the DLC3 (See
step 1 check fuel pump operation (a) to (f)).
(h) Turn the ignition switch ON.
(i) Measure the fuel pressure.
Fuel pressure:
281 - 287 kPa
(2.87 - 2.93 kgf/cm
2, 40.8 - 41.7 psi)
If pressure is high, replace the fuel pressure regulator.
(j) If pressure is low, check these parts:

Fuel hoses and connection

Fuel pump

Fuel filter

Fuel pressure regulator
(k) Remove the TOYOTA hand-held tester from the DLC3.
(l) Reinstall the fuse cover on instrument panel.
(m) Start the engine.
(n) Disconnect the vacuum sensing hose from the fuel pres-
sure regulator.
(o) Measure the fuel pressure at idle.
Fuel pressure:
281 - 287 kPa (2.87 - 2.93 kgf/cm
2, 40.8 - 41.7 psi)
(p) Reconnect the vaccum sensing hose to the fuel pressure
regulator plug the hose end.
(q) Measure the fuel pressure at idle.
Fuel pressure:
226 - 265 kPa (2.3 - 2.6 kgf/cm
2, 33 - 37 psi)
If pressure is not as specified, check the vacuum sensing hose
and fuel pressure regulator.
(r) Stop the engine.
(s) Check that the fuel pressure remains as specified for 5
minutes after the engine has stopped.
Fuel pressure:
147 kPa (1.5 kgf/cm
2, 21 psi) or more
If pressure is not as specified, check the fuel pump, pressure
regulator and/or injector.
(t) After checking fuel pressure, disconnect the negative (-)
terminal cable from the battery and carefully remove the
SST to prevent gasoline from splashing.
SST 09268-45012
(u) Connect the fuel inlet hose to the fuel filter with 2 new gas-
kets and the union bolt.

- MFIFUEL PUMP
MF-7
531 Author
: Date
:
1996 TERCEL (RM440U)
Torque: 29 N´m (290 kgf´cm, 22 ft´lbf)
(v) Check for fuel leakage (See page MF-1).
3. REMOVE REAR SEAT CUSHION
4. DISCONNECT FUEL PUMP AND SENDER GAUGE
CONNECTOR
5. INSPECT FUEL PUMP RESISTANCE
Using an ohmmeter, measure the resistance between terminals
2 and 6.
Resistance: 0.2 - 3.0 W at 20°C (68°F)
If the resistance is not as specified, replace the fuel pump.
6. INSPECT FUEL PUMP OPERATION
Connect the positive (+) lead from the battery to terminal 2 of
the connector, and the negative (-) lead to terminal 6. Check
that the fuel pump operates.
NOTICE:

These tests must be performed quickly (within 10 se-
conds) to prevent the coil from burning out.

Keep the fuel pump as far away from the battery as
possible.

Always perform switching at the battery side.
If operation is not as specified, replace the fuel pump or lead
wire.
7. RECONNECT FUEL PUMP AND SENDER GAUGE
CONNECTOR
8. REINSTALL REAR SEAT CUSHION

SF1PS-02
- MFIFUEL PUMP
MF-9
1996 TERCEL (RM440U)
REMOVAL
CAUTION:
Do not smoke or work near an open flame when working on
the fuel pump.
1. REMOVE REAR SEAT CUSHION
2. REMOVE FLOOR SERVICE HOLE COVER
3. DISCONNECT FUEL PUMP AND SENDER GAUGE
CONNECTOR
HINT:
At the time of installation, plaese refer to the following items.
Check for fuel leakage (See page MF-1).
4. REMOVE FUEL PUMP BRACKET ASSEMBLY FROM
FUEL TANK
CAUTION:
Remove the fuel filler cap to prevent the fuel from flowing
out.
(a) Using SST, disconnect the outlet pipe from the pump
bracket.
HINT:
At the time of installation, plaese refer to the following items. Us-
ing SST.
SST 09631-22020
Torque: 29 N´m (290 kgf´cm, 22 ft´lbf) for use with SST
(See page MF-1)
(b) Remove the 8 bolts.
Torque: 3.4 N´m (35 kgf´cm, 31 in.´lbf)
HINT:
At the time of installation, plaese refer to the following items.
Check for fuel leakage (See page MF-1).
(c) Disconnect the return hoses from the pump bracket.
(d) Pull out the pump bracket assembly.
NOTICE:

Do not damage the fuel pump filter.

Be careful that the arm of the sender gauge should
not bent.

SF1PT-01
MF-10
- MFIFUEL PUMP
1996 TERCEL (RM440U)
DISASSEMBLY
1. REMOVE FUEL CUTOFF VALVE FROM FUEL PUMP
BRACKET
Remove the 2 screws, retainer, fuel cut-off valve and gasket.
HINT:
At the time of installation, plaese refer to the following items.
Install a new gaskt.
Torque: 1.5 N´m (15 kgf´cm, 13 )in.´lbf
2. REMOVE FUEL SENDER GAUGE FROM FUEL PUMP
BRACKET
(a) Remove the screw and disconnect the lead wire from the
pump bracket.
(b) Disconnect the 3 lead wires.
(c) Remove the 2 screws and sender gauge.
3. REMOVE FUEL PUMP FROM FUEL PUMP BRACKET
(a) Pull out the lower side of the fuel pump from the pump
bracket.
(b) Disconnect the connector from the fuel pump.
(c) Disconnect the fuel hose from the fuel pump, and remove
the fuel pump.
(d) Remove the rubber cushion from the fuel pump.
4. REMOVE FUEL PUMP FILTER FROM FUEL PUMP
(a) Using a small screwdriver, remove the clip.
HINT:
At the time of installation, plaese refer to the following items.
Install the pump filter with a new clip.
(b) Pull out the pump filter.

SF1PU-02
- MFIFUEL PRESSURE REGULATOR
MF-15
1996 TERCEL (RM440U)
INSTALLATION
1. INSTALL FUEL PRESSURE REGULATOR
(a) Apply a light coat of gasoline to a new O-ring, and install
it to the pressure regulator.
(b) Attach the pressure regulator to the delivery pipe.
(c) Check that the pressure regulator rotates smothly.
NOTICE:
If it does not rotate smothly, the O-ring may be pinched, so
remove the pressure regulator and perform again steps (b)
and (c) above.
(d) Install the pressure regulator with the 3 bolts.
Torque:8.0 N´m (80kgf´cm, 69 in.´lbf)
2. CONNECT FUEL RETURN HOSE TO FUEL PRES-
SURE REGULATOR
3. CONNECT VACUUM SENSING HOSE TO FUEL PRES-
SURE REGULATOR
4. CHECK FOR FUEL LEAKS (See page MF-1)

SF1PV-02
P20397
Union Bolt
Gasket
SST (Hose)
Fuel Filter
(On Vehicle) SST (Union)
- MFIINJECTOR
MF-19
1996 TERCEL (RM440U)
INSPECTION
1. INSPECT INJECTOR INJECTION
CAUTION:
Keep injector clean of sparks during the test.
(a) Remove the union bolt and 2 gaskets, and disconnect the
fuel inlet hose from the fuel filter outlet.
(b) Connect SST (union and hose) to the fuel filter outlet with
2 gaskets and union bolts.
SST 09268-41046 (90405-09015)
Torque: 29 N´m (290 kgf´cm, 22 ft´lbf)
(c) Remove the pressure regulator from the delivery pipe
(See page MF-14).
(d) Install a O-ring to the fuel inlet of pressure regulator.
(e) Connect SST (hose) to the fuel inlet of the pressure regu-
lator with SST (union) and the 2 bolts.
SST 09268-41046 (09268-41091)
Torque: 8.0 N´m (80 kgf´cm, 69 ft´lbf)
(f) Connect the fuel return hose to the fuel outlet of the pres-
sure regulator.
CAUTION:
Install a suitable vinyl hose onto the injector to prevent
gasoline from splashing out.
(g) Remove the fuse cover on the instrument panel.

- MFIINJECTOR
MF-21
1996 TERCEL (RM440U)
SST 09268-41046, 09842-30070, 09843-18020
(d) Reinstall the pressure regulator to the delivery pipe (See
page MF-15).
(e) Reconnect the fuel inlet hose to the fuel filter outlet with
2 new gaskets and the union bolt.
Torque: 29 N´m (290 kgf´cm, 22 ft´lbf)
(f) Turn the ignition switch OFF.
(g) Disconnect the TOYOTA hand- held tester from the
DLC3.
(h) Reinstall the fuse cover on the instrument panel.