1996 TOYOTA RAV4 torque

AT0952
SST
AX04W−01
AT0953
SST
AT3306
Hold
Lock
Free
Turn
AT2821
AX−22
− AUTOMATIC TRANSAXLE (A540H)TORQUE CONVERTER CLUTCH AND DRIVE PLATE
1996 RAV4 (RM447U)
TORQUE CONVERTER CLUTCH
AND DRIVE PLATE
INSPECTION
1. INSPECT ONE−WAY CLUTCH
(a) Install SST into the inner race of the one−way clutch.
SST 09350−32014 (09351−32010)
(b) Install SST so that it fits in the notch of the converter clutch
hub and outer race of the one−way clutch.
SST 09350−32014 (09351−32020)
(c) With the torque converter clutch standing on its side, the
clutch locks when turned counterclockwise, and rotates
freely and smoothly clockwise.
If necessary, clean the converter clutch and retest the clutch.
Replace the converter clutch if the clutch still fails the test.
2. MEASURE DRIVE PLATE RUNOUT AND INSPECT
RING GEAR
(a) Set up a dial indicator and measure the drive plate runout.
(b) Check the damage of the ring gear.
Maximum runout: 0.20 mm (0.0079 in.)
If the runout is not within the specification, or ring gear is dam-
aged replace the drive plate.
Torque: 83 N·m (850 kgf·cm, 61 ft·lbf)

AT4184
− AUTOMATIC TRANSAXLE (A540H)TORQUE CONVERTER CLUTCH AND DRIVE PLATE
AX−23
1996 RAV4 (RM447U)
3. MEASURE TORQUE CLUTCH CONVERTER SLEEVE
RUNOUT
(a) Temporarily mount the torque converter clutch to the drive
plate. Set up a dial indicator and measure the torque con-
verter clutch sleeve runout.
Maximum runout: 0.30 mm (0.0118 in.)
If the runout is not within the specification, try to correct by reori-
enting the installation of the converter clutch.
HINT:
Mark the position of the converter clutch to ensure correct
installation.
(b) Remove the torque converter clutch.

BO481−01
N11455
N11456
− BODYFRONT BUMPER
BO−5
1996 RAV4 (RM447U)
REMOVAL
1. REMOVE FRONT FENDER MOULDING
2. REMOVE FENDER LINER
3. REMOVE FRONT BUMPER COVER
Remove the 4 bolts, 3 clips, 2 screws and the bumper cover.
4. REMOVE HEADLIGHT UNDER COVER
5. REMOVE HEADLIGHT
6. REMOVE UPPER REINFORCEMENT
Torque: 4.9 N·m (50 kgf·cm, 43 in.·lbf)
7. REMOVE BUMPER STAY
Torque: 4.9 N·m (50 kgf·cm, 43 in.·lbf)

H01976
Centering Bolt
Standard Bolt
BO0ZS−01
N11408
N11409
N11458
BO−8
− BODYHOOD
1996 RAV4 (RM447U)
HOOD
ADJUSTMENT
HINT:
Since the centering bolt is used as the hood hinge and lock set
bolt, the hood and lock cannot be adjusted with it on. Substitute
the bolt with washer for the centering bolt.
1. ADJUST HOOD IN FORWARD/REARWARD AND
LEFT/RIGHT DIRECTIONS
Adjust the hood by loosening the hood side hinge bolts.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
2. ADJUST FRONT EDGE OF HOOD IN VERTICAL
DIRECTIONS
Adjust the hood by turning the cushions.
3. ADJUST HOOD LOCK
Adjust the lock by loosening the 2 bolts and nut.
Torque:
7.5 N·m (75 kgf·cm, 65 in.·lbf) for bolt
8.5 N·m (85 kgf·cm, 74 in.·lbf) for nut

N11460
N17925
N11568
N17926
− BODYFRONT DOOR
BO−11
1996 RAV4 (RM447U)
13. REMOVE DOOR GLASS
(a) Open the door glass until the bolts appear in the service
hole.
(b) Remove the 2 bolts.
NOTICE:
Be careful not to drop the door glass.
(c) Pull up the door glass upwards to remove it.
14. REMOVE WINDOW REGULATOR
(a) Remove the door lock cable from the window regulator.
(b) Remove the 6 nuts.
(c) Disconnect the connector.
(d) Remove the regulator through the service hole.
HINT:
At the time of reassembly, apply MP grease to the window regu-
lator rollers.
15. REMOVE DOOR LOCK
(a) Remove the clip.
(b) Disconnect the link from the door lock.
(c) Remove the 3 screws.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
HINT:
At the time of reassembly, apply adhesive to the 3 screws.
Part No. 08833−00070, THREE BOND 1324 or equiva-
lent
(d) w/ Power door lock:
Disconnect the connector.
(e) Remove the door lock through the service hole.

BO0ZV−01
N11553
N11554
BO2556
− BODYFRONT DOOR
BO−13
1996 RAV4 (RM447U)
ADJUSTMENT
1. ADJUST DOOR IN FORWARD/REARWARD AND VER-
TICAL DIRECTIONS
Using SST, adjust the door by loosening the body side hinge
bolts.
SST 09812−00010
Torque: 23 N·m (230 kgf·cm, 17 ft·lbf)
2. ADJUST DOOR IN LEFT/RIGHT AND VERTICAL
DIRECTIONS
Loosen the door side hinge bolts to adjust.
HINT:
Substitute the standard bolt for the centering bolt (See page
BO−8).
Torque: 25 N·m (260 kgf·cm, 19 ft·lbf)
3. ADJUST DOOR LOCK STRIKER
(a) Check that the door fits and door lock linkages are ad-
justed correctly.
(b) Loosen the striker mounting screws to adjust.
(c) Using a plastic hammer, tap the striker to adjust it.

H03784: 5 Clips
H03785
N14554
− BODYREAR DOOR
BO−17
1996 RAV4 (RM447U)
8. REMOVE DOOR BELT MOULDING
9. REMOVE DOOR GLASS RUN
10. REMOVE DIVISION BAR
11. REMOVE REAR DOOR QUARTER WINDOW WEATH-
ERSTRIP
12. REMOVE REAR DOOR QUARTER WINDOW GLASS
13. REMOVE DOOR GLASS AND WINDOW REGULATOR
ASSEMBLY
(a) Disconnect the connector.
(b) Remove the 3 bolts and nut from the window regulator.
(c) w/o Power Window:
Remove the 3 bolts from the window regulator.
(d) Remove the 2 nuts and glass channel from the window
regulator lift arm bracket, then remove the door glass.
(e) Remove the window regulator through the service hole.
HINT:
At the time of reassembly, apply MP grease to the window regu-
lator rollers.
14. REMOVE DOOR LOCK ASSEMBLY
(a) w/ Power door Lock:
Disconnect the connector.
(b) Disconnect the 2 links from the outside handle.
(c) Remove the 3 screws and door lock assembly.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
HINT:
At the time of reassembly, refer to following procedure.
Apply adhesive to the 3 screws.

BO0ZZ−01
H03786
H03787
BO2556
− BODYREAR DOOR
BO−19
1996 RAV4 (RM447U)
ADJUSTMENT
1. ADJUST DOOR IN FORWARD/REARWARD AND VER-
TICAL DIRECTIONS
Using SST, adjust the door by loosening the body side hinge
bolts.
Torque: 25 N·m (260 kgf·cm, 19 ft·lbf)
2. ADJUST DOOR IN LEFT/RIGHT AND VERTICAL
DIRECTIONS
Loosen the door side hinge bolts to adjust.
HINT:
Substitute the standard bolt for the centering bolt (See page
BO−8).
Torque: 12N·m (122 kgf·cm, 9 ft·lbf)
3. ADJUST DOOR LOCK STRIKER
(a) Check that the door fits and door lock linkages are ad-
justed correctly.
(b) Loosen the striker mounting screws to adjust.
(c) Using a plastic hammer, tap the striker to adjust it.