1996 TOYOTA LAND CRUISER lock

Z06300
BrightDark 2
3
Extinguished
1
−
BODY ELECTRICAL COMBINATION METER
BE−41
1996 LAND CRUISER (RM451U)
25. INSPECT ENGINE OIL LEVEL WARNING CIRCUIT
Disconnect the switch connector and inspect the connector on
wire harness side, as shown.
Tester connectionConditionSpecified condition
2 − GroundConstantContinuity
If continuity is not as specified, inspect the wire harness or
ground point.
26. INSPECT ENGINE OIL LEVEL WARNING LIGHT
(a) Disconnect the connector from the switch.
(b) Ground terminal 1 on the wire harness connector.
(c) Turn the ignition switch ON, and check that the warning
light lights up approximately 40 seconds later.
If the warning light does not light up, inspect bulb or wire har-
ness.
27. INSPECT LIGHT CONTROL RHEOSTAT
(a) Connect terminals 1 and 3 through a 3.4 W test bulb.
(b) Connect the positive (+) lead from the battery to terminal
1 and the negative ( −) lead to terminal 2.
(c) Turn the rheostat knob to fully counterclockwise, and
check that the test bulb goes out.
(d) Gradually turn the rheostat knob to clockwise, and check
that the test bulb brightness changes from dark to bright.
If operation is not as specified, replace the rheostat.
HINT:
Adjust the brightness of illumination lights by rheostat.
A/C Control Assembly
Antenna Switch
Ash Receptacle
Audio
Center Diff. Lock Switch
Cigarette Lighter
Defogger Switch
Hazard Warning Switch
Shift Lever
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z06846
BE1MH−01
BE−46
−
BODY ELECTRICAL POWER WINDOW CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT POWER WINDOW MASTER SWITCH CON- TINUITY
Front Driver’s Switch (Window unlock):
Switch positionTester connectionSpecified condition
UP1 − 2 − 13
6 − 7 − 8Continuity
OFF1 − 2 − 6 − 13Continuity
DOWN1 − 2 − 6
7 − 8 − 13Continuity
Front Driver’s Switch (Window lock):
Switch positionTester connectionSpecified condition
UP1 − 2 − 13
6 − 7 − 8Continuity
OFF1 − 2 − 6 − 13Continuity
DOWN1 − 2 − 6
7 − 8 − 13Continuity
Front Passenger’s Switch (Window unlock):
Switch positionTester connectionSpecified condition
UP1 − 2 − 5
7 − 8 − 12Continuity
OFF1 − 2 − 5 − 12Continuity
DOWN1 − 2 − 12
5 − 7 − 8Continuity
Front Passenger’s Switch (Window lock):
Switch positionTester connectionSpecified condition
UP7 − 8 − 12Continuity
OFF5 − 12Continuity
DOWN5 − 7 − 8Continuity
Rear Left Switch (Window unlock):
Switch positionTester connectionSpecified condition
UP1 − 2 − 9
7 − 8 − 10Continuity
OFF1 − 2 − 9 − 10Continuity
DOWN1 − 2 − 10
7 − 8 − 9Continuity
Rear Left Switch (Window lock):
Switch positionTester connectionSpecified condition
UP7 − 8 − 10Continuity
OFF9 − 10Continuity
DOWN7 − 8 − 9Continuity
Rear Right Switch (Window unlock):
Switch positionTester connectionSpecified condition
UP1 − 2 − 14
7 − 8 − 11Continuity
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z06302
−
BODY ELECTRICAL POWER WINDOW CONTROL SYSTEM
BE−47
1996 LAND CRUISER (RM451U) OFF
1 −
2 − 11 − 14Continuity
DOWN1 − 2 − 11
7 − 8 − 14Continuity
Rear Right Switch (Window lock):
Switch positionTester connectionSpecified condition
UP7 − 8 − 11Continuity
OFF11 − 14Continuity
DOWN7 − 8 − 14Continuity
If continuity is not as specified, replace the master switch.
2. INSPECT POWER WINDOW MASTER SWITCH ILLU-
MINATION
(a) Set the window lock switch to the unlock position.
(b) Connect the positive (+) lead from the battery to terminal 7 and the negative ( −) lead to terminal 1, and check that
all the illuminations light up.
(c) Set the window lock switch to the lock position, and check that all the passenger’s power window switch illumina-
tions go out.
If operation is not as specified, replace the master switch.
3. Using an ammeter: INSPECT ONE TOUCH POWER WINDOW SYSTEM
(a) Disconnect the connector from the master switch.
(b) Connect the positive (+) lead from the ammeter to termi- nal 6 on the wire harness side connector and the negative
(−) lead to negative terminal of the battery.
(c) Connect the positive (+) lead from the battery to terminal 13 on the wire harness side connector.
(d) As the window goes down, check that the current flow is up to approximately 7 A.
(e) Check that the current increases approximately 14.5 A or more when the window stops going down.
HINT:
The circuit breaker opens some 4 − 40 seconds after the win-
dow stops going down, so that check must be made before the
circuit breaker operates.
If the operation is as specified, replace the master switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z06303
Z06304
BE−48
−
BODY ELECTRICAL POWER WINDOW CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
4. Using an ammeter with a current − measuring probe:
INSPECT ONE TOUCH POWER WINDOW SYSTEM
(a) Remove the master switch with connector connected.
(b) Attach a current−measuring probe to terminal 6 of the
wire harness.
(c) Turn the ignition switch ON, and set the power window switch in the down position.
(d) As the window goes down, check that the current flow is up to approximately 7 A.
(e) Check that the current increases approximately 14.5 A or more when the window stops going down.
HINT:
The circuit breaker opens some 4 − 40 seconds after the win-
dow stops going down, so check must be made before the cir-
cuit breaker operates.
If operation is as specified, replace the master switch.
5. INSPECT POWER WINDOW SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
UP1 − 5, 3 − 4Continuity
OFF1 − 2, 3 − 4Continuity
DOWN1 − 2, 4 − 5Continuity
If continuity is not as specified, replace the switch.
6. Front Door:
INSPECT LEFT SIDE DOOR POWER WINDOW MO-
TOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
3 and the negative ( −) lead to terminal 1, and check that
the motor turns clockwise.
(b) Reverse the polarity, and check that the motor turns coun-
terclockwise.
If operation is not as specified, replace the motor.
7. Rear Door: INSPECT LEFT SIDE DOOR POWER WINDOW MO-
TOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal 1 and the negative ( −) lead to terminal 2, and check that
the motor turns counterclockwise.
(b) Reverse the polarity, and check that the motor turns
clockwise.
If operation is not as specified, replace the motor.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z06307
Z06308
Z06309
14
Z06310
4
1
−
BODY ELECTRICAL POWER WINDOW CONTROL SYSTEM
BE−49
1996 LAND CRUISER (RM451U)
8. INSPECT DRIVER’S DOOR PTC OPERATION
(a) Disconnect the connector from the master switch.
(b) Connect the positive (+) lead from the battery to terminal
6 and the negative ( −) lead to terminal 13 on the wire har-
ness side connecter and raise the window to full closed
position.
(c) Continue to apply voltage, check that the current changes
from approximately 14 A to less that 1 A within 4 to 90 se-
conds.
(d) Disconnect the leads from terminals.
(e) After approximately 90 seconds, connect the positive (+) lead from the battery to terminal 13 and negative ( −) lead
to terminal 6, check that the window beginsto desced.
If operation is not as specified, replace the motor.
9. INSPECT PASSENGER’S DOOR PTC OPERATION
(a) Disconnect the connector from the power window switch.
(b) Connect the positive (+) lead from the battery to terminal 1 and the negative ( −) lead to terminal 4 on the wire har-
ness side connector, and raise the window to full closed
position.
(c) Connect the positive (+) lead from the battery to terminal 1 on the wire harness side connector.
(d) Disconnect the leads from terminals.
(e) After approximately 90 seconds, connect the positive (+)
lead from the battery to terminal 4 and negative ( −) lead
to terminal 1, check that the window begins to descend.
If operation is not as specified, replace the motor.
10. INSPECT P ASSENGER’S DOOR MOT OR OPERATION
(a) Connect the positive (+) lead from the battery to terminal 1 and the negative ( −) lead to terminal 3, and check that
the motor turns clockwise.
(b) Reverse the polarity, and check that the motor turns coun-
terclockwise.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE−50
−
BODY ELECTRICAL POWER WINDOW CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
11. INSPECT REAR RIGHT SIDE DOOR MOTOR OPER-
AION
(a) Connect the positive (+) lead from the battery to terminal
2 and the negative ( −) lead to terminal 1, and check that
the motor turns counterclockwise.
(b) Reverse the polarity, and check that the motor turns clockwise.
If operation is not as specified, replace the motor.
12. INSPECT RIGHT SIDE PTC OPERATION
13. INSPECT POWER MAIN RELAY CONTINUITY
ConditionTester connectionSpecified condition
Constant1 − 3Continuity
Apply B+ between
terminals 1 and 3.2 − 4Continuity
If continuity is not as specified, replace the relay.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1MI−01
−
BODY ELECTRICAL POWER DOOR LOCK CONTROL SYSTEM
BE−51
1189
Author: Date:
1996 LAND CRUISER (RM451U)
POWER DOOR LOCK CONTROL SYSTEM
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z06846
BE1MJ−01
BE−52
−
BODY ELECTRICAL POWER DOOR LOCK CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT DRIVER’S DOOR LOCK MANUAL SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
LOCK1 − 2 − 4Continuity
OFF−No continuity
UNLOCK1 − 2 − 3Continuity
If continuity is not as specified, replace the switch.
2. INSPECT DOOR KEY LOCK AND UNLOCK SWITCH
CONTINUITY
Switch positionTester connectionSpecified condition
LOCK1 − 3Continuity
OFF−No continuity
UNLOCK2 − 3Continuity
If continuity is not as specified, replace the switch.
HINT:
Door key lock and unlock switch is built into the front door lock
assembly.
3. INSPECT KEY UNLOCK WARNING SWITCH CONTI-
NUITY (See page BE−11 )
4. INSPECT DOOR COURTESY SWITCH CONTINUITY (See page BE−21 )
5. INSPECT DOOR LOCK MOTOR OPERATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010