1996 TOYOTA LAND CRUISER bearing

−
PREPARATION SUSPENSION AND AXLE
PP−43
92
Author: Date:
1996 LAND CRUISER (RM451U)
09504−00011Differential Side Bearing
Adjusting Nut WrenchFront differential
Rear differential
09504−22011Differential Side Bearing
ReplacerRear differential
09506−35010Differential Drive Pinion Rear
Bearing ReplacerRear differential
Rear suspension
09509−25011Rear Axle Bearing Lock Nut
WrenchRear axle
09517−36010Rear Axle Shaft Oil Seal
Replacer −Rear axle
09550−10013Replacer Set ”B”Rear differential
Rear suspension
(09553−10010)Differential Side Bearing
Replacer
(09557−10011)Differential Drive Pinion
Front Bearing Replacer
09550−60010Differential Side Bearing
ReplacerRear differential
09556−22010Drive Pinion Front Bearing
RemoverFront differential
Rear differential
09605−60010Steering Knuckle Bearing Cup
Replacer−Front axle
09606−60020Steering Knuckle Bearing RemoverFront axle
09607−60020Front Wheel Adjusting Nut WrenchFront axle
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP−44
−
PREPARATION SUSPENSION AND AXLE
93
Author: Date:
1996 LAND CRUISER (RM451U)
09611−22012Tie Rod End PullerFront axle
09612−65014Steering Worm Bearing PullerFront axle
(09612−01010)Claw ”A”
(09612−01050)Hanger Pin with Nut
09618−60010Front Axle & Drive Shaft Bearing
ReplacerFront axle
09710−22021Front Suspension Bushing Tool
SetRear suspension
(09710−01071)Lower Arm Bushing Remover
09710−22042Rear Suspension Bushing Tool SetFront suspension
(09710−02051)Base
(09710−02061)Replacer
(09710−02071)Bushing Remover & Replacer
09710−30050Suspension Arm Bushing ReplacerFront suspension
09726−40010Lower Control Shaft Bearing
ReplacerFront differential
Rear differential
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
PREPARATION SUSPENSION AND AXLE
PP−45
94
Author: Date:
1996 LAND CRUISER (RM451U)
09727−30021Coil Spring Compressor
09950−00020Bearing RemoverFront differential
Rear differential
09950−30011Puller A SetFront differential
Rear differential
(09951−03010)Upper Plate
(09953−03010)Center Bolt
(09954−03010)Arm
(09955−03030)Lower Plate 130
(09956−03020)Adapter 18
09950−40011Puller B SetFront differential
Rear differential
(09951−04010)Hanger 150
(09952−04010)Slide Arm
(09953−04020)Center Bolt 150
(09954−04010)Arm 25
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP3KM−01
PP−56
−
PREPARATION STEERING
105
Author: Date:
1996 LAND CRUISER (RM451U)
STEERING
SST (Special Service Tools)
09527−10011Rear Axle Shaft Bearing RemoverPS vane pump
09610−55012Pitman Arm PullerSteering linkage
09611−22012Tie Rod End PullerSteering linkage
09616−00011Steering Worm Bearing Adjusting
SocketPS gear
09628−62011Ball Joint PullerSteering linkage
09630−00014Power Steering Gear Housing
Overhaul Tool Set
(09631−00051)No.3 WrenchPS gear
(09631−00121)Teflon Ring FormerPS gear
(09631−00142)Overhaul StandPS gear
09631−10030Oil Seal RemoverPS vane pump
09631−22020Power Steering Hose Nut
14 x 17 mm Wrench SetPS gear
09640−10010Power Steering Pressure Gauge
Set
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PR06N−01
−
PROPELLER SHAFT TROUBLESHOOTING
PR−1
849
Author: Date:
1996 LAND CRUISER (RM451U)
TROUBLESHOOTING
PROBLEM SYMPTOMS TABLE
Use the table below to help you find the cause of the problem. The numbers \
indicate the priority of the likely
cause of the problem. Check each part in order. If necessary, replace these parts.
SymptomSuspect AreaSee page
Noise3. Seeve yoke spline: worn
4. Spider bearing: worn or stuckPR−4
PR−4
Vibration
1. Sleeve yoke spline: stuck
2. Propeller shaft: runout
3. Propeller shaft: imbalancePR−4
PR−4
−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PR06O−02
Q10862
 Spider Grease Fitting
 Snap Ring
 Spider Bearing
Dust Cover
Grease Fitting Propeller Shaft
Flange Yoke
 Snap Ring
 Spider Bearing

Spider
Sleeve Yoke
N·m (kgf·cm, ft·lbf)
 Non− reusable part
Flange Yoke
Propeller Shaft
 Spider
Grease Fitting
Dust Cover

Spider Bearing

Snap Ring
Grease Fitting
Sleeve Yoke
: Specified torque
Flange Yoke
Flange Yoke
Front Propeller Shaft
74 (750, 54)
88 (900, 65)
74 (750, 54)
74 (750, 54)
74 (750, 54)
74 (750, 54)
88 (900, 65)
88 (900, 65)
88 (900, 65)
Rear propeller Shaft
 Spider
 Spider Bearing 
Snap Ring
Grease
Fitting
Grease Fitting
PR−2
−
PROPELLER SHAFT PROPELLER SHAFT ASSEMBLY
850
Author: Date:
1996 LAND CRUISER (RM451U)
PROPELLER SHAFT ASSEMBLY
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PR0310
PR06Q−01
PR0014
Matchmarks
PR0056
PR−4
−
PROPELLER SHAFT PROPELLER SHAFT ASSEMBLY
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT FRONT AND REAR PROPELLER SHAFTS FOR DAMAGE OR RUNOUT
Using a dial indicator, check the runout of shafts. Maximum runout: 0.8 mm (0.031 in.)
If shaft runout is greater than maximum, replace the shaft.
2. REMOVE SLEEVE YOKE FROM PROPELLER SHAFT
Place matchmarks on the sleeve yoke and shaft.
(1) Pull out the sleeve yoke from the shaft.
(2) Remove the dust cover from the shaft.
3. INSPECT SPIDER BEARING
Check the spider bearings for wear or damage.
Check the spider bearing axial play by turning the yoke
with holding the shaft tightly.
Bearing axial play: Maximum 0.05 mm (0.0020 in.)
If necessary, replace the spider bearing.
4. INSERT SLEEVE YOKE INTO PROPELLER SHAFT
(a) Apply MP grease to the propeller shaft spline and sleeve yoke sliding surface.
(b) Align the matchmarks on the sleeve yoke propeller shaft.
(c) Install the propeller shaft into the sleeve yoke.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PR0058
MatchmarksPR06S−03
Z00753
PR0060
SSTA
PR0061
Z00754
SST
PR−6
−
PROPELLER SHAFT SPIDER BEARING
854
Author: Date:
1996 LAND CRUISER (RM451U)
SPIDER BEARING
REPLACEMENT
NOTICE:
Be careful not to grip the propeller shaft tube too tightly in
the vise as this will cause deformation.
1. REMOVE PROPELLER SHAFT (See page PR−3)
2. PLACE MATCHMARKS ON SHAFT AND YOKE
3. REMOVE SNAP RINGS
(a) Using a brass bar and hammer, slightly tap in the bearing
outer races.
(b) Using 2 screwdrivers, remove the 4 snap rings from the grooves.
4. REMOVE SPIDER BEARINGS
(a) Using SST, push out the bearing from the flange. SST 09332−25010
HINT:
Sufficiently raise the part indicated by A so that it does not come
into contact with the bearing.
(b) Clamp the bearing outer race in a vise and tap off the flange with a hammer.
HINT:
Remove the bearing on the opposite side by the same proce-
dure.
(c) Install the 2 removed bearing outer races to the spider.
(d) Using SST, push out the bearing from the yoke. SST 09332−25010
(e) Clamp the outer bearing race in a vise and tap off the yoke
with a hammer.
HINT:
Remove the bearing on the opposite side in the same proce-
dure.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010