1996 TOYOTA LAND CRUISER Fuel pump

−
INTRODUCTION HOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMSIN−25
1996 LAND CRUISER (RM451U)
5. PROBLEM SYMPTOMS TABLE
The suspected circuits or parts for each problem symptom are shown in th\
e table below. Use this table to
troubleshoot the problem when a ”Normal” code is displayed in the \
diagnostic trouble code check but the
problem is still occurring. Numbers in the table indicate the inspection order in which the circuits or parts
should be checked.
HINT:
When the problem is not detected by the diagnostic system even though the pr\
oblem symptom is present,
it is considered that the problem is occurring outside the detection ran\
ge of the diagnostic system, or that
the problem is occurring in a system other than the diagnostic system.
Symptom
Suspected AreaSee page
Engine does not crank (Does not start)
No initial combustion (Does not start)
No complete combustion (Does not start) 1. Starter and starter relay
1. ECM power source circuit
2. Fuel pump control circuit
3. ECM
1. Starter signal circuit
2. Fuel pump control circuit 1. Fuel pump control circuit
DI−147
DI−151
IN−29
PROBLEM SYMPTOMS TABLE
1. Compression
2. Fuel pump control circuit 1. A/C signal circuit
2. Fuel pump control circuit 1. A/C signal circuit (Compressor circuit)
2. ECM power source circuit 1. Starter signal circuit
2. Fuel pump control circuit1. Starter signal circuit
2. Fuel pump control circuit
3. Compression
idling)
High engine idle speed (Poor idling) Hot engine
Cold engine (Difficult to start) Engine cranks normally (Difficult to start)
AC−88 DI−144
DI−151
EM−3 DI−151
 Problem Symptom Page
Indicates the page where the flow chart for each circuit
is located.
 Circuit Inspection, Inspection Order
Indicates the circuit which needs to be checked for each problem
symptom. Check in the order indicated by the numbers.
 Circuit or Part Name
Indicates the circuit or part which needs to be checked.
ST−2
ST−17
DI−144
DI−151
DI−144
DI−151
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IN−34
−
INTRODUCTION TERMS
34
Author: Date:
1996 LAND CRUISER (RM451U)
CW
Curb W
eight
DCDirect Current
DEFDefogger
DFLDeflector
DIFF.Differential
DIFF. LOCKDifferential Lock
D/INJDirect Injection
DLIDistributorless Ignition
DOHCDouble Over Head Cam
DPDash Pot
DSDead Soak
DSPDigital Signal Processor
EBDElectronic Brake Force Distribution
ECAMEngine Control And Measurement System
ECDElectronic Controlled Diesel
ECDYEddy Current Dynamometer
ECUElectronic Control Unit
EDElectro−Deposited Coating
EDICElectric Diesel Injection Control
EDUElectronic Driving Unit
EFIElectronic Fuel Injection
E/GEngine
EGR−VMExhaust Gas Recirculation −Vacuum Modulator
ELREmergency Locking Retractor
ENGEngine
ESAElectronic Spark Advance
ETCSElectronic Throttle Control System
EVPEvaporator
E−VRVElectric V acuum Regulating V alve
EXHExhaust
FEFuel Economy
FFFront−Engine Front− Wheel−Drive
F/GFuel Gage
FIPGFormed In Place Gasket
FLFusible Link
F/PFuel Pump
FPUFuel Pressure Up
FrFront
FRFront−Engine Rear− Wheel−Drive
F/WFlywheel
FW/DFlywheel Damper
FWDFront−Wheel−Drive
GASGasoline
GSAGear Shift Actuator
GNDGround
HACHigh Altitude Compensator
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IN0CI−02
IN−38
−
INTRODUCTION TERMS
1996 LAND CRUISER (RM451U)
GLOSSARY OF SAE AND TOYOTA TERMS
This glossary lists all SAE− J1930 terms and abbreviations used in this manual in compliance with SAE\
rec-
ommendations, as well as their TOYOTA equivalents.
SAE
ABBREVIATIONSSAE TERMSTOYOT A TERMS
( ) −−ABBREVIA TIONS
A/CAir ConditioningAir Conditioner
ACLAir CleanerAir Cleaner, A/CL
AIRSecondary Air InjectionAir Injection (AI)
APAccelerator Pedal−
B+Battery Positive Voltage+B, Battery Voltage
BAROBarometric PressureHAC
CACCharge Air CoolerIntercooler
CARBCarburetorCarburetor
CFIContinuous Fuel Injection−
CKPCrankshaft PositionCrank Angle
CLClosed LoopClosed Loop
CMPCamshaft PositionCam Angle
CPPClutch Pedal Position−
CTOXContinuous T rap Oxidizer−
CTPClosed Throttle PositionLL ON, Idle ON
DFIDirect Fuel Injection (Diesel)Direct Injection (DI)
DIDistributor Ignition−
DLC1
DLC2
DLC3Data Link Connector 1
Data Link Connector 2
Data Link Connector 31: Check Connector
2: Total Diagnosis Comunication Link (TDCL)
3: OBD II Diagnostic Connector
DTCDiagnostic Trouble CodeDiagnostic Code
DTMDiagnostic Test Mode−
ECLEngine Control Level−
ECMEngine Control ModuleEngine ECU (Electronic Control Unit)
ECTEngine Coolant T emperatureCoolant Temperature, Water Temperature (THW)
EEPROMElectrically Erasable Programmable Read Only Memory
Electrically Erasable Programmable Read Only Memory
(EEPROM),
Erasable Programmable Read Only Memory (EPROM)
EFEEarly Fuel EvaporationCold Mixture Heater (CMH), Heat Control Valve (HCV)
EGRExhaust Gas RecirculationExhaust Gas Recirculation (EGR)
EIElectronic IgnitionTOYOTA Distributorless Ignition (TDI)
EMEngine ModificationEngine Modification (EM)
EPROMErasable Programmable Read Only MemoryProgrammable Read Only Memory (PROM)
EVAPEvaporative EmissionEvaporative Emission Control (EVAP)
FCFan Control−
FEEPROMFlash Electrically Erasable Programmable
Read Only Memory−
FEPROMFlash Erasable Programmable Read Only Memory−
FFFlexible Fuel−
FPFuel PumpFuel Pump
GENGeneratorAlternator
GNDGroundGround (GND)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P09401
P22893
DI−10
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
OK
Proceed to matrix chart of problem symp-
toms on page DI−19.
7 Check fuel pressure.
PREPARATION:
(a) Be sure that enough fuel is in the tank.
(b) Connect the TOYOTA hand−held tester to the DLC3.
(c) Turn ignition switch ON and push TOYOTA hand −held
tester main switch ON.
(d) Use ACTIVE TEST mode to operate the fuel pump.
(e) If you have no TOYOTA hand−held tester, connect the positive (+) and negative (−) leads from the battery to the
fuel pump connector (See page SF−6).
CHECK:
Check for fuel pressure in the fuel return hose when it is pinched
off.
HINT:
At this time, you will hear a fuel flowing noise.
NG Proceed to page SF−6 and continue to trouble-
shoot.
OK
8 Check for spark.
PREPARATION:
(a) Remove No.2 and No.3 cylinder head cover.
(b) Disconnect high −tension cord from spark plug.
(c) Remove spark plug.
(d) Install the spark plug to the high −tension cord.
(e) Ground the spark plug.
(f) Disconnect injector connector.
CHECK:
Check if spark occurs while engine is being cranked.
NOTICE:
To prevent excess fuel being injected from the injectors
during this test, don’t crank the engine for more than 5 − 10
seconds at a time.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−12
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
(b) TOYOTA Enhanced Signals.
TOYOTA hand−held tester displayMeasurement ItemNormal Condition*
MISFIRE RPMEngine RPM for first misfire rangeMisfire 0: 0 rpm
MISFIRE LOADEngine load for first misfire rangeMisfire 0: 0 g/r
INJECTORFuel injection time for cylinder No.1Idling: 2.0 − 3.5 ms
IAC STEP POSIntake Air Control Valve step position
Opening position step motor type IAC valveIdling: 10 − 50 step
STARTER SIGStarter SignalCranking: ON
CTP SWClosed Throttle Position Switch SignalThrottle Fully Closed: ON
A/C SIGA/C Switch SignalA/C ON: ON
PNP SWPark/Neutral Position Switch SignalP or N Position: ON
STOP LIGHT SWStop Light Switch SignalStop light switch ON: ON
FC IDLFuel Cut Idle: Fuel cut when throttle valve fully
closed, during decelerationFuel cut operating: ON
FC TAUFuel Cut TAU: Fuel cut during very light loadFuel cut operating: ON
CYL#1 − CYL#6Ratio of revolution variation for each cylinder
when variation is large0%
IGNITIONIgnition rate for all cylinders every 1,000 revolu-
tions0 − 3,000 rpm
EGRT GASEGR Gas Temp. Sensor V alueEGR not operating: Temp. between intake air
temp. and engine coolant temp.
EGR SYSTEMEGR System Operating ConditionIdling: OFF
FUEL PRES UP VSVFuel Pressure Up VSV SignalHigh temp. restarting: ON
FUEL PUMPFuel Pump SignalIdling: ON
TOTAL FT B1Total Fuel Trim Bank 1: Average value for fuel
trim system of bank 1Idling: 0.8 − 1.2 V
O2 LR B1, S1
Oxygen Sensor Lean Rich Bank 1, Sensor 1
Response time for oxygen sensor output to
switch from lean to rich
Idling after warmed up: 0 − 1,000 msec.
O2 RL B1, S1
Oxygen Sensor Rich Lean Bank 1, Sensor 1
Response time for oxygen sensor output to
switch from rich to lean
Idling after warmed up: 0 − 1,000 msec.
∗: If no conditions are specifically stated for ”ldling”, it means t\
he shift lever is at N or P position, the A/C switch
is OFF and all accessory switches are OFF.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5OY−03
−
DIAGNOSTICS ENGINE
DI−19
1996 LAND CRUISER (RM451U)
PROBLEM SYMPTOMS TABLE
When the malfunction code is not confirmed in the DTC check and the problem \
still can not be confirmed
in the basic inspection, then proceed to this step and perform troubleshooting according to the numbered
order given in the table below.
SymptomSuspect AreaSee page
Engine does not crank (Does not start)1. Starting systemST−16
No initial combustion (Does not start)1. ECM power source circuit
2. Fuel pump control circuitDI−11 0
DI−11 5
No complete combustion (Does not start)1. Fuel pump control circuitDI−11 5
Engine cranks normally (Difficult to start)
1. Starter signal circuit
2. Fuel pump control circuit
3. CompressionDI−103
DI−11 5 EM−3
Cold engine (Difficult to start)1. Starter signal circuit
2. Fuel pump control circuitDI−103DI−11 5
Hot engine (Difficult to start)
1. Starter signal circuit
2. Fuel pressure control circuit
3. Fuel pump control circuitDI−103
DI−125DI−11 5
High engine idle speed (Poor idling)1. A/C signal circuit
2. ECM power source circuitAC−5
DI−11 0
Low engine idle speed (Poor idling)1. A/C signal circuit
2. Fuel pump control circuitAC−5
DI−11 5
Rough idling (Poor idling)1. Compression
2. Fuel pump control circuitEM−3
DI−11 5
Hunting (Poor idling)1. ECM power source circuit
2. Fuel pump control circuitDI−11 0
DI−11 5
Hesitation/Poor acceleration (Poor driveability)1. Fuel pump control circuit
2. A/T faultyDI−11 5
DI−147
Surging (Poor driveability)1. Fuel pump control circuitDI−11 5
Soon after starting (Engine stall)1. Fuel pump control circuitDI−11 5
During A/C operation (Engine stall)1. A/C signal circuit
2. Engine control module (ECM)AC−5
IN−18
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−52
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
2 Check for heated oxygen sensor (bank 1 sensor 1) data.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the OBD II scan tool or TOYOTA hand−held tester to the DLC3.
(c) Warm up engine to normal operating temperature.
CHECK:
Read the heated oxygen sensor (bank 1 sensor 1) output voltage and sho\
rt −term fuel trim.
RESULT:
PatternHeated o xygen sensor (bank 1 sensor 1) output voltageShort−term fuel trim
1Lean condition (Changes at 0.55 V or less)Changes at about +20 %
2Rich condition (Changes at 0.4 V or more)Changes at about −20 %
3Except 1 and 2
3 Check for heated oxygen sensor
(bank 1 sensor 1) (See page SF−64 ).
1, 2
3 Check fuel pressure (See page SF−6 ).
NG Check and repair fuel pump, pressure
regulator, fuel pipe line and filter
(See page SF−1 ).
OK
4 Check injector injection (See page SF−29).
NG Replace injector.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00165
ON
#10 #20 #40 #50
#30 #60
BE6653
P24661
−
DIAGNOSTICS ENGINE
DI−57
1996 LAND CRUISER (RM451U)
2 Check voltage of ECM terminal for injector of failed cylinder.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Measure voltage between applicable terminal of ECM connec-
tor and body ground.
OK:
Voltage: 9 − 14 V
OK Go to step 4.
NG
3 Check injector of misfiring cylinder (See page SF−29).
NG Replace injector.
OK
Check for open and short in harness and con-
nector between injector and ECM (See page
IN−28 ).
4 Check fuel pressure (See page SF−6 ).
NG Check and repair fuel pump, pressure regulator,
fuel pipe line and filter (See page SF−1).
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010