1995 TOYOTA SUPRA wiper arm

FRONT WIPER REMOVAL
1. REMOVE THESE PARTS:
(a) Wiper arm and blade
(b) Cowl top ventilator louver
2. REMOVE FRONT WIPER MOTOR
(a) Disconnect the connector, then unfasten the 3 bolts.
(b) Remove the wiper motor with the link.
FRONT WIPER INSTALLATION
1. INSTALL THESE PARTS:
(a) Wiper motor with link
(b) Cowl top ventilator louver
2. INSTALL WIPER ARM AND BLADE
(a) Install the wiper arms and operate the wipers once and turn
the wiper switch OFF.
(b) Adjust the installation positions of the wiper arms to the
positions shown in the illustration.
(A) Approx. 32.4 mm (1.28 in.)
(B) Approx. 33.7 mm (1.33 in.)
(c) Torque the nut.
Torque: 22 NVm (225 kgfVcm, 16 ftVlbf)
FRONT WASHER NOZZLE ADJUSTMENT
1. INSPECT FRONT WASHER NOZZLE
(a) While operating the washer, check that both the point where
the washer fluid from the upper nozzles hits the windshield,
and the up surge area, are within the range indicated by the
hatched line.
(A) Approx. 275 mm (10.8 in.)
(B) Approx. 150 mm (5.9 in.)
(C) Approx. 50 mm (2.0 in.)
(D) Within 100 mm (3.9 in.)
(b) Ensure that the lower point where the washer fluid hits the
windshield is within the range of the wiping pattern (the area
of the glass which is wiped by the wiper blades.
2. ADJUST FRONT WASHER NOZZLE
Using a tool like that shown in the illustration, change the
direction of the nozzle hole to adjust the point where washer
fluid strikes the windshield.
± BODYWIPER AND WASHERBO±21

REAR WIPER REMOVAL
1. REMOVE WIPER ARM AND BLADE
2. REMOVE BACK DOOR TRIM BOARD
3. REMOVE WIPER MOTOR ASSEMBLY
(a) Disconnect the connector, then unfasten the 3 bolts.
(b) Remove the motor.
REAR WIPER INSTALLATION
1. INSTALL THESE PARTS:
(a) Wiper motor
(b) Back door trim board
2. INSTALL WIPER ARM AND BLADE
(a) Install the wiper arm and operate the wiper once and turn the
wiper switch OFF.
(b) Adjust the top of the wiper blade to the installation mark
printed on the glass.
(c) Torque the nut.
Torque: 11 NVm (110 kgfVcm, 8.0 ftVlbf)
REAR WASHER NOZZLE ADJUSTMENT
1. INSPECT REAR WASHER NOZZLE
While operating the washer, check that the point where the
washer fluid hits the back door glass is within the range indi-
cated by the hatched line.
(A) Approx. 300 mm (11.8 in.)
(B) Approx. 150 mm (5.9 in.)
2. ADJUST REAR WASHER NOZZLE
(See step 2 on page BO±21) BO±22
± BODYWIPER AND WASHER

WINDSHIELD MOULDING REMOVAL
1. REMOVE THESE PARTS:
(a) Wiper arm and blade
(b) Cowl top ventilator louver
2. REMOVE WINDSHIELD MOULDING
(a) Using a knife, cut off the moulding as shown.
(b) Cut away the adhesive at the moulding installation area as
much as possible.
NOTICE: Do not damage the body with the knife.
WINDSHIELD MOULDING INSTALLATION
1. CUT ADHESIVE AT MOULDING INSTALLATION AREA
Using the knife, cut off the adhesive around the moulding
installation area.
2. APPLY ADHESIVE AT MOULDING INSTALLATION AREA
3. INSTALL WINDSHIELD MOULDING
Place the moulding onto the body and tap it by hand.
4. INSTALL THESE PARTS:
(a) Cowl top ventilator louver
(b) Wiper arm and blade
Torque: 22 NVm (225 kgfVcm, 16 ftVlbf)
BO±24± BODYWINDSHIELD MOULDING

WINDSHIELD REMOVAL
1. REMOVE THESE PARTS:
(a) Inner rear view mirror
(b) Sunvisors and holders
(c) Assist grip
(d) Front pillar garnishes
(e) Hood
(f) Wiper arms and blades
(g) Cowl top ventilator louver
2. REMOVE WINDSHIELD MOULDING
Using a knife, cut off the moulding as shown.
NOTICE: Do not damage the body with the knife.
3. REMOVE WINDSHIELD GLASS
(a) Push piano wire through from the interior.
(b) Tie both wire ends to a wooden block or similar object.
HINT: Apply adhesive tape to the outer surface of the glass
to keep the surface from being scratched.
± BODYWINDSHIELDBO±31

(c) Use a scraper to remove any excess or protruding adhesive.
(d) Fasten glass securely until the adhesive sets.
13. INSTALL WINDSHIELD MOULDING
Place the moulding onto the body and install it by hand.
14. INSPECT FOR LEAKS AND REPAIR
(a) Do a leak test after the hardening time has elapsed.
(b) Seal any leak with auto glass sealer.
Part No. 08833±00030
15. INSTALL THESE PARTS:
(a) Cowl top ventilator louver
(b) Wiper arms and blades
Torque: 22 NVm (225 kgfVcm, 16 ftVlbf)
(c) Hood
Torque: 13 NVm (130 kgfVcm, 9.4 ftVlbf)
(d) Front pillar garnishes
(e) Assist grip
(f) Sunvisors and holders
(g) Inner rear view mirror
± BODYWINDSHIELDBO±35

BACK DOOR MOULDING AND GLASS
REMOVAL
1. DISCONNECT DEFOGGER CONNECTOR
2. REMOVE THESE PARTS:
(a) Rear wiper arm and blade
(b) Back door trim board
(c) Back door opening trim
3. REMOVE BACK DOOR MOULDING
Using a knife, cut off the moulding as shown.
NOTICE: Do not damage the body with the knife.
4. REMOVE BACK DOOR GLASS AND MOULDING
HINT: Remove the glass and moulding in the same manner
as the windshield. (See pages BO±31 and 32)
BACK DOOR MOULDING AND GLASS
INSTALLATION
1. INSTALL BACK DOOR MOULDING
Place the moulding around the glass and install it by hand.
HINT: Always remove the back door glass to install the
moulding.
2. INSTALL BACK DOOR GLASS
HINT: Install the glass in the same manner as the windshield.
(See pages BO±32 to 35)
(a) Coat contact surface of the glass with primer ºGº.
(b) Apply adhesive.
H: 12 mm (0.47 in.)
3. INSTALL THESE PARTS:
(a) Back door opening trim
(b) Back door trim board
(c) Rear wiper arm and blade
Torque: 11 NVm (110 kgfVcm, 8.0 ftVlbf)
4. CONNECT DEFOGGER CONNECTOR BO±40
± BODYBACK DOOR MOULDING AND GLASS

SERVICE SPECIFICATIONS
TORQUE SPECIFICATIONS
 Part tightened NVm kgfVcm ftVlbf
 FRONT BUMPER ±± ±± ±±
  Reinforcement x Body 5.9 60 52 in.Vlbf
  Front bumper cover x Body 5.9 60 52 in.Vlbf REAR BUMPER ±± ±± ±± 
  Reinforcement x Body
 
 42
 
 430
 
 31
  Rear bumper cover x Body 5.9 60 52 in.Vlbf
 HOOD ±± ±± ±±
  Hood hinge x Hood 13 130 9.4
  Hood lock x Body 8.8 90 78 in.Vlbf
 FRONT DOOR ±± ±± ±±  Door hinge x Body 52 530 38 
  Door hinge x Door panel
 
 25
 
 260
 
 19
  Door lock x Door panel 5.4 55 48 in.Vlbf
  Window regulator x Door panel 7.8 80 69 in.Vlbf
  Window guide lower plate x Door panel 5.9 60 52 in.Vlbf
  Door window upper stop x Door panel 13 130 9.4
 BACK DOOR ±± ±± ±±  Back door hinge x Body 21 210 15 
  Back door hinge x Back door
 
 13
 
 130
 
 9.4
  Door lock x Body 19 195 14
  Door lock striker x Body 13 130 9.4
  Back door damper stay x Body 5.9 60 52 in.Vlbf
  Back door damper stay x Back door 7.8 80 69 in.Vlbf
 WIPER AND WASHER ±± ±± ±± Front Wiper ±± ±± ±± 
  Wiper arm x Wiper link
 
 22
 
 225
 
 16
 Rear Wiper ±± ±± ±±
  Wiper arm x Wiper motor 11 11 0 8.0
 INSTRUMENT PANEL ±± ±± ±±
  Steering column x Instrument panel reinforcement 25 260 19
  Front passenger airbag assembly x Instrument panel reinforcement 21 210 15  Front passenger airbag assembly x Instrument panel 8.8 90 78 in.Vlbf 
  Steering wheel x Steering column 
 35 
 360 
 26
  Steering wheel pad x Steering wheel 7.1 72 62 in.Vlbf
± BODYSERVICE SPECIFICATIONSBO±63