1995 TOYOTA SUPRA fuel pressure

 
 
 
 
 
 
 
 
 
 
Crankshaft
(cont'd) 
 
 
 
 
 
 
 
 
 
Main bearing center wall thickness (Reference)
Mark 1
Mark 2
Mark 3
Mark 4
Mark 5
Crank pin diameter STD
U/S 0.25
Circle runout Maximum
Main journal taper and out±of±round Maximum
Crank pin taper and out±of±round Maximum 
 
 
 
 
 
 
 
 
 
1.994±1.997 mm (0.0785±0.0786 in.)
1.997±2.000 mm (0.0786±0.0787 in.)
2.000±2.003 mm (0.0787±0.0789 in.)
2.003±2.006 mm (0.0789±0.0790 in.)
2.006±2.009 mm (0.0790±0.0791 in.)
51.982±52.000 mm (2.0465±2.0472 in.)
51.745±51.755 mm (2.0372±2.0376 in.)
0.06 mm (0.0024 in.)
0.02 mm (0.0008 in.)
0.02 mm (0.0008 in.)
TORQUE SPECIFICATIONS
 Part tightened NVm kgfVcm ftVlbf
 Timing belt plate X Oil pump (2JZ±GTE) 7.8 80 69 in.Vlbf
 Idler pulley X Oil pump 34 350 25
 Crankshaft pulley X Crankshaft 324 3,300 239
 Camshaft timing pulley X Camshaft 79 810 59
Timing belt tensioner X Oil pump2627020 Drive belt tensioner X Cylinder head 21 210 15 Drive belt tensioner damper X Tensioner arm (2JZ±GTE M/T) 20 200 14 Drive belt tensioner damper X Tensioner bracket (2JZ±GTE M/T) 20 200 14 EGR cooler X Cylinder head 8.8 90 78 in.Vlbf ECT sensor X Cylinder head (2JZ±GE) 20 200 14 ECT sender gauge X Cylinder head (2JZ±GE) 20 200 14
 Engine hanger X Cylinder head 39 400 29
 Camshaft position sensor X Cylinder head (2JZ±GTE) 8.8 90 78 in.Vlbf
 
 
 
Cylinder head X Cylinder block 1st
2nd
3rd 



34
Turn 905
Turn 905 
 
 
350 
 
 
25
 Camshaft bearing cap X Cylinder head 20 200 14
 No.4 timing belt cover X Cylinder head 8.8 90 78 in.Vlbf
 Cylinder head cover X Cylinder head 2JZ±GE
2JZ±GTE 8.3
5.4 85
55 74 in.Vlbf
48 in.Vlbf
 
 Intake manifold X Cylinder head 2JZ±GE
2JZ±GTE 


27
27 
 280
280 
 20
20
 Fuel inlet pipe X Delivery pipe 42 420 30 Intake manifold stay X Intake manifold 39 400 29
 Intake manifold stay X Cylinder block 39 400 29
 Water outlet X Cylinder head (2JZ±GTE) 21 210 15
 Vacuum control valve set X Intake manifold (2JZ±GE) 21 210 15
 
 
Air intake chamber X Intake manifold 2JZ±GE
2JZ±GTE 


27
27 
 
280
280 
 
20
20
 Air intake chamber stay X Cylinder head (2JZ±GE) 18 185 13
 Air intake chamber stay X Air intake chamber (2JZ±GE) 18 185 13
 Exhaust manifold X Cylinder head 39 400 29
Pressure tank X Intake manifold (2JZ±GTE)2121015 
 Main bearing cap X Cylinder block 1st
2nd
 


44
Turn 905
 
 450
 
 33
EG±138± ENGINEENGINE MECHANICAL

 Connecting rod cap X Connecting rod 1st
2nd 29
Turn 905 300 22
 
Oil nozzle X Crankshaft (2JZ±GTE)
 
8.8
 
90
 
78 in.Vlbf Rear oil seal retainer X Cylinder block 5.9 60 52 in.Vlbf Crankshaft position sensor X Cylinder block (2JZ±GTE) 8.8 90 78 in.Vlbf Engine mounting bracket X Cylinder block 58 590 43 Engine coolant drain plug X Cylinder block 29 300 22 Union for oil cooler X Cylinder block (2JZ±GTE) 39 400 29
 Knock sensor X Cylinder block 44 450 33
 Oil pressure switch X Cylinder block 14 150 11
 Fuel pipe support X Cylinder block 14 145 10
 Oil filter bracket X Cylinder block 88 900 65
 No.2 water bypass pipe X Water pump 21 210 15
 No.2 water bypass pipe X Cylinder block 21 210 15
 Flywheel X Crankshaft (M/T) 1st
2nd 49
Turn 905 500 36
 Drive plate X Crankshaft (A/T) 83 850 61 Clutch cover X Flywheel (M/T) 19 195 14 
 Cylinder block X Transmission 14 mm head
17 mm head 
 39
72 
 400
730 
 29
43
 Clutch service hole cover X Clutch housing (2JZ±GTE M/T) 12 120 9
 Drive plate X Torque converter clutch (A/T) 33 340 25
 Oil cooler tube X Union for transmission (A/T) 34 350 25
 Rear support member X Body 25 260 19
 Rear support member X Engine rear mounting insulator 13 135 10
 Front suspension crossmember X Engine mounting insulator 59 600 43
 Transmission shift lever X Shift lever retainer (M/T) 19 195 14
 Transmission control rod X Shift lever (A/T) 13 130 9
Clutch release cylinder X Transmission (M/T)131309 
Clutch line tube X No.1 oil pan
 
37
 
380
 
27 Ground strap X Transmission (M/T) 37 380 27 Fuel inlet hose X Fuel pipe support 29 300 22 
 A/C compressor X Cylinder block for stud bolt
for bolt and nut 
 26
52 
 265
530 
 19
38
 PS pump front bracket X Cylinder block (2JZ±GE) 58 590 43
 PS pump front bracket X Oil pump (2JZ±GE) 52 530 38
 PS pump housing X PS pump bracket 58 590 43
 PS pump bracket X A/C compressor 58 590 43
 PS pump bracket X Cylinder block 39 400 29
 PS pump rear stay X PS pump bracket 39 400 29
 PS pump rear stay X Intake manifold stay (2JZ±GE) 39 400 29
 Rear center floor crossmember brace X Body (2JZ±GTE) 28 290 21
No.2 front exhaust pipe X Exhaust manifold6263046 No.2 front exhaust pipe X Front exhaust pipe 58 590 43 Pipe support bracket X Transmission 43 440 32 Front exhaust pipe X Center exhaust pipe 58 590 43 Center exhaust pipe X Tailpipe 19 195 14 
 
Sub heated oxygen sensor
x Front exhaust pipe (2JZ±GE (California), 2JZ±GTE) 
 
20 
 
200 
 
14
± ENGINEENGINE MECHANICALEG±139

09205±76030Cylinder Head Setting Bolt
Tightening Adaptor
09268±41045Injection Measuring Tool Set
(09268±41070)No.4 Union
(09268±41090)No.7 Union
(90405±09015)No.1 Union
09268±45012 EFI Fuel Pressure Gauge
ECT sensor
09612±24014 Steering Gear Housing Overhaul
Tool Set
(09617±24011) Steering Rack Wrench
09631±22020 Power Steering Hose Nut
14 x 17 mm Wrench Set
09808±14010Fuel Sender Gauge Tool Assy
09816±30010 Oil Pressure Switch Socket
09842±30070 Wiring ªFº EFI InspectionInjector
Knock sensor
Fuel line flare nut
Fuel pressure pulsation damper
SFI SYSTEM (2JZ±GE)
PREPARATION
SST (SPECIAL SERVICE TOOLS)
± ENGINESFI SYSTEM (2JZ±GE)EG±187

9. Use SST for inspection or test of the injector or its wiring
connector.
SST 09842±30070
FUEL SYSTEM
1. When disconnecting the high pressure fuel line, a large
amount of gasoline will spill out, so observe the following
procedures:
(a) Disconnect the fuel pump connector.
(b) Start the engine. After the engine has stopped on its own,
turn off the ignition switch.
(c) Put a container under the connection.
(d) Slowly loosen the connection.
(e) Disconnect the connection.
(f) Plug the connection with a rubber plug.
(g) Reconnect the fuel pump connector.
2. When connecting the flare nut or union bolt on the high
pressure pipe union, observe the following procedures:
Union Bolt Type:
(a) Always use a new gasket.
(b) Tighten the union bolt by hand.
(c) Tighten the union bolt to the specified torque.
Torque: 29 NVm (300 kgfVcm, 22 ftVlbf)
Flare Nut Type:
(a) Apply a light coat of engine oil to the flare nut, and tighten the
flare nut by hand.
(b) Using SST, tighten the flare nut to specified torque.
SST 09631±22020
Torque: 30 NVm (310 kgfVcm, 22 ftVlbf)
HINT: Use a torque wrench with a fulcrum length of 30 cm
(11.81 in.).
± ENGINESFI SYSTEM (2JZ±GE)EG±191

3. Observe the following precautions when removing and
installing the injectors.
(a) Never reuse the O±ring.
(b) When placing a new O±ring on the injector, take care not to
damage it in any way.
(c) Coat a new O±ring with spindle oil or gasoline before
installing±never use engine, gear or brake oil.
4. Install the injector to the delivery pipe and intake manifold as
shown in the illustration.
5. Check that there are no fuel leaks after doing maintenance
anywhere on the fuel system.
(a) Using SST, connect terminals +B and FP of the DLC 1.
SST 09843±18020
(b) With engine stopped, turn the ignition switch ON.
(c) Pinch the fuel return hose.
The pressure in the high pressure line will rise to approx. 392
kPa (4 kgf/cm
2, 57 psi). In this state, check to see that there
are no leaks from any part of the fuel system.
NOTICE: Always pinch the hose. Avoid bending as it may
cause the hose to crack.
(d) Turn the ignition switch OFF.
(e) Remove the SST from the DLC1.
SST 09843±18020 EG±192
± ENGINESFI SYSTEM (2JZ±GE)

FUEL PUMP
ON±VEHICLE INSPECTION
1. CHECK FUEL PUMP OPERATION
(a) Using SST, connect terminals +B and FP of the DLC 1.
SST 09843±18020
(b) Turn the ignition switch ON.
NOTICE: Do not start the engine.
(c) Check that there is pressure in the fuel inlet hose from the fuel
filter.
HINT: If there is fuel pressure, you will hear the sound of fuel
flowing.
If there is no pressure, check the following parts:
wFuse
wEFI main relay
wFuel pump
wECM
wWiring connections
(d) Turn the ignition switch OFF.
(e) Remove the SST from the DLC1.
SST 09843±18020
2. CHECK FUEL PRESSURE
(a) Check the battery voltage is above 12 V.
(b) Disconnect the negative (±) terminals cable from the battery.
(c) Remove the 2 nuts, and disconnect the No.2 vacuum pipe
from the air intake chamber and intake manifold.
(d) Remove the union bolt and 2 gaskets, disconnect the fuel
inlet pipe from the delivery pipe.
CAUTION:

Put a shop towel under the delivery pipe.

Slowly loosen the union bolt.
(e) Install the fuel inlet pipe and SST (pressure gauge) to the
delivery pipe with the 3 gaskets and SST (union bolt).
SST 09268±45012
Torque: 42 NVm (420 kgfVcm, 30 ftVlbf)
(f) Wipe off any splattered gasoline.
(g) Using SST, connect terminals +B and FP of the DLC 1.
SST 09843±18020
± ENGINESFI SYSTEM (2JZ±GE)EG±193

(h) Reconnect the negative (±) terminal cable to the battery.
(i) Turn the ignition switch ON.
(j) Measure the fuel pressure.
Fuel pressure:
265±304 kPa (2.7±3.1 kgf/cm
2, 38±44 psi)
If pressure is high, replace the fuel pressure regulator.
If pressure is low, check the following parts:
wFuel hoses and connections
wFuel pump
wFuel filter
wFuel pressure regulator
(k) Remove the SST from the DLC1.
SST 09843±18020
(l) Start the engine.
(m) Disconnect the vacuum sensing hose from the fuel pressure
regulator, and plug the hose end.
(n) Measure the fuel pressure at idle.
Fuel pressure:
265±304 kPa (2.7±3.1 kgf/cm
2, 38±44 psi)
(o) Reconnect the vacuum sensing hose to the fuel pressure
regulator.
(p) Measure the fuel pressure at idle.
Fuel pressure:
196±235 kPa (2.0±2.4 kgf/cm
2, 28±34 psi)
If pressure is not as specified, check the vacuum sensing
hose and fuel pressure regulator.
(q) Stop the engine.
(r) Check that the fuel pressure remains as specified for 5
minutes after the engine has stopped.
Fuel pressure:
147 kPa (1.5 kgf/cm
2, 21 psi) or more
If pressure is not as specified, check the fuel pump, pressure
regulator and/or injectors.
(s) After checking fuel pressure, disconnect the negative (±)
terminal cable from the battery and carefully remove the SST
to prevent gasoline from splashing.
SST 09268±45012
(t) Install the fuel inlet pipe to the delivery pipe with 2 new
gaskets and the union bolt.
Torque: 42 NVm (420 kgfVcm2, 30 ftVlbf)
(u) Install the No.2 vacuum pipe with the 2 nuts.
Torque: 27 NVm (270 kgfVcm2, 20 ftVlbf)
(v) Reconnect the negative (±) terminal cable to the battery.
(w) Check for fuel leaks.
(See item 5 in fuel system in precaution) EG±194
± ENGINESFI SYSTEM (2JZ±GE)

FUEL PRESSURE REGULATOR
COMPONENTS FOR REMOVAL AND
INSTALLATION
FUEL PRESSURE REGULATOR
REMOVAL
1. DISCONNECT VACUUM SENSING HOSE FROM FUEL
PRESSURE REGULATOR
2. DISCONNECT FUEL RETURN PIPE FROM FUEL
PRESSURE REGULATOR
Remove the union bolt and 2 gaskets, and disconnect the re-
turn pipe from the pressure regulator.
CAUTION:

Put a shop rag under the pressure regulator.

Slowly loosen the union bolt.
3. REMOVE FUEL PRESSURE REGULATOR
(a) Remove the 2 bolts, and pull out the pressure regulator.
(b) Remove the O±ring from the pressure regulator. EG±200
± ENGINESFI SYSTEM (2JZ±GE)