FRONT WIPER REMOVAL
1. REMOVE THESE PARTS:
(a) Wiper arm and blade
(b) Cowl top ventilator louver
2. REMOVE FRONT WIPER MOTOR
(a) Disconnect the connector, then unfasten the 3 bolts.
(b) Remove the wiper motor with the link.
FRONT WIPER INSTALLATION
1. INSTALL THESE PARTS:
(a) Wiper motor with link
(b) Cowl top ventilator louver
2. INSTALL WIPER ARM AND BLADE
(a) Install the wiper arms and operate the wipers once and turn
the wiper switch OFF.
(b) Adjust the installation positions of the wiper arms to the
positions shown in the illustration.
(A) Approx. 32.4 mm (1.28 in.)
(B) Approx. 33.7 mm (1.33 in.)
(c) Torque the nut.
Torque: 22 NVm (225 kgfVcm, 16 ftVlbf)
FRONT WASHER NOZZLE ADJUSTMENT
1. INSPECT FRONT WASHER NOZZLE
(a) While operating the washer, check that both the point where
the washer fluid from the upper nozzles hits the windshield,
and the up surge area, are within the range indicated by the
hatched line.
(A) Approx. 275 mm (10.8 in.)
(B) Approx. 150 mm (5.9 in.)
(C) Approx. 50 mm (2.0 in.)
(D) Within 100 mm (3.9 in.)
(b) Ensure that the lower point where the washer fluid hits the
windshield is within the range of the wiping pattern (the area
of the glass which is wiped by the wiper blades.
2. ADJUST FRONT WASHER NOZZLE
Using a tool like that shown in the illustration, change the
direction of the nozzle hole to adjust the point where washer
fluid strikes the windshield.
± BODYWIPER AND WASHERBO±21
There are some maintenance and inspection
items which are considered to be the owner's re-
sponsibility. They can be performed by the owner
or be can have them done at a service shop.
These items include those which should be
checked on a daily basis, those which, in most
cases, do not require (special) tools and those
which are considered to be reasonable for the
owner to perform. Items and procedures for gen-
eral maintenance are as follows:
OUTSIDE VEHICLE
1. TIRES
(a) Check the pressure with a gauge. Adjust if
necessary.
(b) Check for cuts, damage, uneven or excessive
wear.
2. WHEEL NUTS
When checking the tires, check the nuts for
looseness or for missing nuts. If necessary,
tighten them.
3. WINDSHIELD WIPER BLADES
Check for wear or cracks whenever they do not
wipe clean. Replace if necessary.
4. FLUID LEAKS
(a) Check underneath for leaking fuel, oil, water or
other fluid.
(b) If you smell gasoline fumes or notice any leak,
have the cause found and corrected.
5. DOORS AND ENGINE HOOD
(a) Check that all doors including the trunk lid
operate smoothly, and that all latches lock
securely.
(b) Check that the engine hood secondary latch
secures the hood from opening when the
primary latch is released.
INSIDE VEHICLE
6. LIGHTS
(a) C h e c k t h a t t h e headlights, stop lights,
tail±lights, turn signal lights, and other lights
are all working.
(b) Check the headlight aiming.7. WARNING LIGHT AND BUZZERS
Check that all warning lights and buzzers
function properly.
8. HORN
Check that it is working.
9. WINDSHIELD GLASS
Check for scratches, pits or abrasions.
10. WINDSHIELD WIPER AND WASHER
(a) Check operation of the wipers and washer.
(b) Check that the wipers do not streak.
11. WINDSHIELD DEFROSTER
Check that the air comes out from the defrost-
er outlet when operating the heater air condi-
tioner at defroster mode.
12. REAR VIEW MIRROR
Check that it is mounted securely.
13. SUN VISORS
Check that they move freely and are
mounted securely.
14. STEERING WHEEL
Check that it has the specified freeplay. Be
alert for changes in steering condition, such
as excessive steering effort, excessive free-
play or strange noise.
15. SEATS
(a) Check that all front seat controls such as seat
adjusters, seatback recliner, etc. operate
smoothly.
(b) Check that all latches lock securely in any
position.
(c) Check that the locks hold securely in any
latched position.
(d) Check that the head restraints move up and
down smoothly and that the locks hold
securely in any latched position.
(e) For folding±down rear seat backs, check that
the latches lock securely.
16. SEAT BELTS
(a) Check that the seat belt system such as
buckles, retractors and anchors operate
properly and smoothly.
(b) Check that the belt webbing is not cut, frayed,
worn or damaged.
17. ACCELERATOR PEDAL
Check the pedal for smooth operation and
uneven pedal effort or catching.
GENERAL MAINTENANCE
± MAINTENANCEGENERAL MAINTENANCEMA±17
