Page 731 of 2248
8. Parking (Hand) Brake
B4M0705A
1Parking brake lever
2Parking brake switch
3Lock nut
4Adjusting nut
5Equalizer
6Bracket
7Clamp
8Parking brake cable RH
9Cable guide
10Clamp
(Rear disc brake model only)
11Parking brake cable LH
Tightening torque: N⋅m (kg-m, ft-lb)
T1: 5.9±1.5 (0.60±0.15, 4.3±1.1)
T2: 18±5 (1.8±0.5, 13.0±3.6)
T3: 32±10 (3.3±1.0, 24±7)
16
4-4COMPONENT PARTS
8. Parking (Hand) Brake
Page 732 of 2248
9. ABS/TCS System
1. SENSOR AND CONTROL MODULE
B4M0706A
1Rear ABS sensor RH
2ABS spacer
3Rear ABS sensor LH
4ABS/TCS control module
5Front ABS sensor LH
6Front ABS sensor RH
Tightening torque: N⋅m (kg-m, ft-lb)
T1: 32±10 (3.3±1.0, 24±7)
17
4-4COMPONENT PARTS
9. ABS/TCS System
Page 733 of 2248
2. HYDRAULIC UNIT
B4M0707A
1ABS/TCS Hydraulic
control unit
2Rear-RH outlet
3Front-LH outlet
4Front-RH outlet
5Rear-LH outlet
6Secondary inlet
7Primary inlet
8Secondary suction line
9Primary suction line
10Bumper
11Bracket
12Pressure switch
13Valve relay
14Motor relay
Tightening torque: N⋅m (kg-m, ft-lb)
T1: 7.4±2.0 (0.75±0.2, 5.4±1.4)
T2: 29±7 (3.0±0.7, 21.7±5.1)
T3: 32±10 (3.3±1.0, 24±7)
T4: 38±10 (3.8±1.0, 27±7)
T5: 3.1±1 (0.32±0.1, 2.3±0.7)
18
4-4COMPONENT PARTS
9. ABS/TCS System
Page 734 of 2248
1. Front Disc Brake
B4M0065B
1Air bleeder screw
2Guide pin
3Guide pin boot
4Piston
5Piston seal
6Piston boot
7Lock pin boot
8Lock pin sleeve
9Caliper body
10Lock pin
11Housing
12Support
13Pad clip
14Outer shim
15Outer pad
16Inner pad
17Inner shim
18Shim
19Disc rotor
20Disc cover
Tightening torque: N⋅m (kg-m, ft-lb)
T1: 8±1 (0.8±0.1, 5.8±0.7)
T2: 18±5 (1.8±0.5, 13.0±3.6)
T3: 39±5 (4±0.5, 28.9±3.6)
T4: 78±10 (8.0±1.0, 58±7)
19
4-4SERVICE PROCEDURE
1. Front Disc Brake
Page 739 of 2248
B4M0074A
G4M0363
F: INSTALLATION
1) Install disc rotor on hub.
2) Install support on housing.
Tightening torque:
78±10 N⋅m (8±1 kg-m, 58±7 ft-lb)
CAUTION:
Always replace the pads for both the left and right
wheels at the same time. Also replace pad clips if they
are twisted or worn.
A wear indicator is provided on the inner disc brake
pad. If the pad wears down to such an extent that the
end of the wear indicator contacts the disc rotor, a
squeaking sound is produced as the wheel rotates. If
this sound is heard, replace the pad.
When replacing the pad, replace pads of the right
and left wheels at the same time.
3) Apply thin coat of PBC GREASE (Part No. 003607000)
to the frictional portion between pad and pad clip.
4) Install pads, rubber coated shim and stainless shim on
support.
5) Install caliper body on support.
Tightening torque:
39±5 N⋅m (4±0.5 kg-m, 28.9±3.6 ft-lb)
6) Connect brake hose.
Tightening torque:
18±3 N⋅m (1.8±0.3 kg-m, 13.0±2.2 ft-lb)
CAUTION:
Replace brake hose gaskets with new ones.
7) Bleed air from brake system.
24
4-4SERVICE PROCEDURE
1. Front Disc Brake
Page 740 of 2248
2. Rear Disc Brake
G4M0912
1Guide pin
2Lock pin
3Lock pin boot
4Lock pin sleeve
5Air bleeder screw
6Guide pin boot
7Caliper body
8Piston seal
9Piston
10Piston boot
11Boot ring
12Pad clip
13Shim
14Inner shim
15Inner pad
16Outer pad
17Support
18Outer shim
19Disc rotor
Tightening torque: N⋅m (kg-m, ft-lb)
T1: 8±1 (0.8±0.1, 5.8±0.7)
T2: 20±4 (2.0±0.4, 14.5±2.9)
T3: 26±5 (2.7±0.5, 19.5±3.6)
T4: 52±6 (5.3±0.6, 38.3±4.3)
G4M0378
A: ON-CAR SERVICE
1. PAD
1) Remove lock pin.
25
4-4SERVICE PROCEDURE
2. Rear Disc Brake
Page 741 of 2248
G4M0379
2) Raise caliper body.
3) Remove pad from support.
G4M0362
4) Check pad thickness (including back metal).
Pad thickness: A
Standard value 15.0 mm (0.591 in)
Wear limit 6.5 mm (0.256 in)
CAUTION:
Always replace the pads for both the left and right
wheels at the same time. Also replace pad clips if they
are twisted or worn.
A wear indicator is provided on the inner disc brake
pad. If the pad wears down to such an extent that the
end of the wear indicator contacts the disc rotor, a
squeaking sound is produced as the wheel rotates. If
this sound is heard, replace the pad.
Replace pad if there is oil or grease on it.
G4M0363
5) Apply thin coat of PBC GREASE (Part No. 03607000)
to the frictional portion between pad and pad clip.
6) Install pad on support.
7) Install caliper body on support.
Tightening torque:
20±4 N⋅m (2.0±0.4 kg-m, 14.5±2.9 ft-lb)
NOTE:
If it is difficult to push piston during pad replacement,
loosen air bleeder to facilitate work.
26
4-4SERVICE PROCEDURE
2. Rear Disc Brake
Page 745 of 2248
F: INSTALLATION
1) Install disc rotor on hub.
2) Install support on back plate.
Tightening torque:
52±6 N⋅m (5.3±0.6 kg-m, 38.3±4.3 ft-lb)
CAUTION:
Always replace the pads for both the left and right
wheels at the same time. Also replace pad clips if they
are twisted or worn.
A wear indicator is provided on the inner disc brake
pad. If the pad wears down to such an extent that the
end of the wear indicator contacts the disc rotor, a
squeaking sound is produced as the wheel rotates. If
this sound is heard, replace the pad.
Replace pads if there is oil or grease on them.
3) Apply thin coat of PBC GREASE (Part No. 003607000)
to the frictional portion between pad and pad clip.
G4M0363
4) Install pads on support.
5) Install caliper body on support.
Tightening torque:
20±4 N⋅m (2.0±0.4 kg-m, 14.5±2.9 ft-lb)
6) Connect brake hose.
Tightening torque:
18±3 N⋅m (1.8±0.3 kg-m, 13.0±2.2 ft-lb)
CAUTION:
The brake hose must be connected without any
twist.
Replace brake hose gaskets with new ones.
7) Bleed air from brake system.
30
4-4SERVICE PROCEDURE
2. Rear Disc Brake
