1995 NISSAN ALMERA N15 Throttle

ENGINEANDEMISSION CONTROLOVERALLSYSTEM
Vacuum HoseDrawing
GA 14DE, GA16DE forEurope
GA15DE
Pressureregulator ~.

"

Throttle body
\1--"

10 ~

EGR valve
~L/

~1 ~
t~:::-
EGRvalve
&
EVAP

z:
0
5
I
L
W
canister purge

4
controlsolenoid
8 ToEVAP canister
¥
valve
EGR valve &EVAP canister purge BPTvalve 3-wayconnector
control solenoid valve

MIT
models
AIT
models

AIT
models
SEF125R

(1)
Pressure regulator tointake
manifold
@ EGR valve to3-way connector
@ 3-way connector to3-way con-
nector
@ BPTvalve to3-way connector

@
3-way connector toEVAP canis-
ter
@ EGR valve
&
EVAP canister
purge control solenoid valveto
3-way connector
(j)

EGR valve
&
EVAP canister
purge control solenoid valveto
air cleaner
@ EGRvalve
&
EVAP canister
purge control solenoid valveto
throttle body

@
Pressure regulator tothrottle
body

@l
EGR valve
&
EV AP canister
purge control solenoid valveto
air duct

EC-22 @

Throttle bodytoEVAP canister
@ EVAP canister purgecontrol
valve tothrottle body
@ EVAP canister purgecontrol
valve toEVAP canister
@ EVAP canister purgecontrol
valve toresonator

@
Throttle bodytoEVAP canister

ENGINEANDEMISSION BASICCONTROL SYSTEMDESCRIPTION
System Chart

I
Camshaft positionsensor

'1
Fuel
injection
&
mixture
ratio control Injectors
Knock sensor
Distributorignitionsystem Powertransistor
Mass airflow sensor
Engine coolant temperature
sensor
Ignition switch Idle
aircontrol system
Fuel pump control
*4

IACV-AAC valve(WithFICD
solenoid valve)
Fuel pump relay

•

'5

Throttle
positionsensor
Neutral positionllnhibitor
switch
Air conditioner switch ECM
(ECCS
control
module)
2

Oxygen sensormonitor

&
On-board diagnostic system

5
Torque converter clutchcan-
cel solenoid valvecontrol
(A/T models) Malfunction
indicatorlamp
(On theinstrument panel)
Torque converter clutchsole-
noid valve
VTC solenoid valve

*6
Air
conditioner relays
Cooling
fanrelay
EVAP canister purgecontrol
solenoid valve
Cooling
fancontrol
Air conditioner cutcontrol
during acceleration
Valve timing control
EVAP canister purgecontrol

7

6

Power
steering oilpressure
switch Battery
voltage
Intake airtemperature sensor

*3

I

Vehicle speedsensor

*2

I
Oxygen sensor

8
'8

Electrical load
• Rear defogger switch
• Lighting switch EGR

&
EVAP canister purge
control EGR
valve
&
EVAP canister
purge control solenoid valve
*1: Except forEurope andIsrael
*2: Heated oxygen sensor(ForEurope andIsrael, andAustralia A/Tmodels)
Oxygen sensor(Except forEurope andIsrael, andAustralia A/Tmodels)
*3: For Australia
*4: IACV-AAC valveandIACV-FICD solenoidvalve(ForEurope andIsrael)
IACV-AAC valve(withFICDsolenoid valve)(Except forEurope andIsrael)
'5: Except forEurope
*6: GA16DE exceptforEurope andIsrael
*7: GA16DE MITmodels exceptforEurope, IsraelandAustralia
*8: For Europe andIsrael andAustralia, andGA15DE MITmodels

EC-23

ENGINEANDEMISSION BASICCONTROL SYSTEMDESCRIPTION
Multipart FuelInjection (MFI)System
INPUT/OUTPUT SIGNALLINE

Camshaft positionsensor
Mass airflow sensor
Engine coolant temperature sensor

*1
Oxygen sensor
Throttle position sensor
Neutral position/Inhibitor switch
Vehicle speedsensor
~gnition switch
Air conditioner switch
Power steering oilpressure switch
Battery Engine
speedandpiston position
Amount ofintake air
Engine coolant temperature
Density ofoxygen inexhaust gas
Throttle position
Throttle valveidleposition
Gear position
Vehicle speed
Start signal
Air conditioner operation
Power steering loadsignal
Battery voltage ECM
(ECCS
control module) Injector
*1: Heated oxygen sensor(ForEurope andIsrael, andAustralia A/Tmodels)
Oxygen sensor(Except forEurope andIsrael, andAustralia A/Tmodels)

BASIC MULTIPORT FUELINJECTION
SYSTEM

The amount offuel injected fromthefuel injector
is determined bythe ECM. TheECM controls the
length oftime thevalve remains open(injection
pulse duration). Theamount offuel injected isa
program valueinthe ECM memory. Theprogram
value ispreset byengine operating conditions.
These conditions aredetermined byinput signals
(for engine speedandintake air)from boththe
camshaft positionsensorandthemass airflow
sensor.
VARIOUS
FUELINJECTION
INCREASE/DECREASE COMPENSATION

In addition, theamount offuel injected iscom-
pensated toimprove engineperformance under
various operating conditions aslisted below.

<
Fuel increase>
• During warm-up
• When starting theengine
• During acceleration
• Hot-engine operation
• When selector leverischanged from"N"to
"D"
(AfT
models only)
• High-load, high-speed operation

<
Fuel decrease>
• During deceleration

EC-24

ENGINEANDEMISSION BASICCONTROL SYSTEMDESCRIPTION
Distributor Ignition(DI)System
INPUT/OUTPUT SIGNALLINE

Camshaft positionsensor
Mass airflow sensor
Engine coolant temperature sensor
Throttle position sensor
Vehicle speedsensor
Ignition switch

*1
Knock sensor
Neutral position/Inhibitor switch
Battery
*1: Except forEurope andIsrael Engine
speedandpiston position
Amount ofintake air
Engine coolant temperature
Throttle position
Throttle valveidleposition
Vehicle speed
Start signal
Engine knocking
Gear position
Battery voltage ECM
(ECCS
control
module) Power
transistor
•

Tp

(msec)

1.75

~ 1.50

.~

~ 1.25

"S
0.

C
1.00
o

. ~ 0.75

E
A

N

600 1,000 1,4001,8002,200

Engine speed(rpm) SEF742M
SYSTEM
DESCRIPTION

The ignition timingiscontrolled bythe ECM tomaintain thebest
air-fuel ratioforevery running condition ofthe engine.
The ignition timingdataisstored inthe ECM. Thisdata forms
the map shown.
The ECM receives information suchasthe injection pulsewidth
and camshaft positionsensorsignal.Computing thisinforma-
tion, ignition signals aretransmitted tothe power transistor .
e.g., N:1,800 rpm,Tp:1.50 msec
AOBTDC
During thefollowing conditions, theignition timingisrevised by
the ECM according tothe other datastored inthe ECM.
• Atstarting
• During warm-up
• Atidle
• Hot engine operation
• During acceleration
• During high-load operation (VTCon)-GA 16DE except for
Europe andIsrael
Except forEurope andIsrael
The knock sensor retardsystem isdesigned onlyforemergen-
cies. Thebasic ignition timingisprogrammed withintheanti-
knocking zone,ifrecommended fuelisused under drycondi-
tions. Theretard system doesnotoperate undernormal driv-
ing conditions.
If engine knocking occurs,theknock sensor monitors thecon-
dition. Thesignal istransmitted tothe ECM (ECCS control mod-
ule). TheECM retards theignition timingtoeliminate theknock-
ing condition.

EC-27

ENGINEANDEMISSION BASICCONTROL SYSTEMDESCRIPTION ~
Air Conditioning CutControl
INPUT/OUTPUT SIGNALLINE

Air conditioner switch
Neutral position/Inhibitor switch
Throttle position sensor
Camshaft positionsensor
Engine coolant temperature sensor
Ignition switch
Vehicle speedsensor
Power steering oilpressure switch Air
conditioner "ON"signal
Neutral position
Throttle
valve
opening angle
Engine speed
Engine coolant temperature
Start signal
Vehicle speed
Power steering loadsignal ECM
(ECCS
control
module) Air
conditioner
relay

SYSTEM DESCRIPTION

This system improves acceler8.tion whentheairconditioner isused.
When theaccelerator pedalisfully depressed, theairconditioner isturned offfor afew seconds.

Fuel CutControl (atnoload
&
high engine
speed)
INPUT/OUTPUT SIGNALLINE

Vehicle speedsensor
Neutral position/Inhibitor switchVehicle
speed
Neutral position
Throttle position sensor
Engine coolant temperature sensor
Camshaft positionsensor Throttle
position
Engine coolant temperature
Engine speed ECM
(ECCS
control
module) Injectors
If the engine speedisabove 2,500rpmwith noload (for
example, inneutral andengine speedover2,500 rpm)fuelwill
be cut offafter some time.Theexact timewhen thefuel iscut
off varies basedonengine speed.
Fuel cutwill operate untiltheengine speedreaches 2,000rpm,
then fuelcutiscancelled.

NOTE:
This function isdifferent thandeceleration controllistedunder
"Multiport FuelInjection (MFI)System" onEC-24.
EC-28

EVAPORATIVEEMISSIONSYSTEM

•

SEF126R
EVAP
canister
'1
EVAP canister
purge control
solenoid valve

or

'2 EGR valve
&

EVAP canister
purge control
solenoid
valve To
EGR
I

valve
I

,

I

1

1

I

I

I

Vacuum :
signal line I
I

I
I
I

I

I

-- -- --- -- ------ __....J

r---
------- -------- ---------,

Fuel fillercap
with vacuum
relief valve

------------,

I

I

I

I

I

I

I

I
I

I
I

'-

Throttle
valve~

I

Fuel check valve
Intake
manifold
'1 :GA 16DE M/Tmodels exceptforEurope,
Israel andAustralia
'2 :For Europe, IsraelandAustralia,
and GA15DE
M/T
models
~ :GA 15, 16DE AlTmodels exceptfor
Europe, IsraelandAustralia
.. :Air

Q :
Fuel vapor

Theevaporative emissionsystemisused toreduce hydrocar-
bons emitted intotheatmosphere fromthefuel system. This
reduction ofhydrocarbons isaccomplished byactivated char-
coals inthe EVAP canister.
The fuelvapor fromsealed fueltank isled into theEVAP can-
ister when theengine isoff. The fuelvapor isthen stored inthe
EVAP canister. TheEVAP canister retainsthefuel vapor until
the EVAP canister ispurged byair.
When theengine isrunning, theairisdrawn through thebot-
tom ofthe EVAP canister. Thefuel vapor willthen beled tothe
intake manifold.
When theengine runsatidle, theEVAP canister purgecontrol
valve isclosed. Onlyasmall amount ofvapor flowsintothe
intake manifold throughtheconstant purgeorifice.
As the engine speedincreases andthethrottle vacuum rises,
the purge control valveopens. Thevapor issucked through
both main purge andconstant purgeorifices.

@Q
@
AEC664Inspection
EVAP CANISTER

Check EVAPcanister asfollows:
1. Blow airinport
@
and ensure thatthere isno leakage.

2.
Apply vacuum toport
@.
[Approximately
-13.3
to
-20.0
kPa

(-133
to
-200
mbar,
-100
to
-150
mmHg,
-3.94
to
-5.91
inHg)]
3. Cover port
CID
with hand.
4. Blow airinport
@
and ensure freeflow outofport
CID.

EC-29

POSITIVECRANKCASE VENTILATION
Description
intothecrankcase. Inthis process theairpasses
through thehose connecting airinlet tubes to
rocker cover.
Under full-throttle condition,themanifold vacuum
is insufficient todraw theblow-by flowthrough
the valve. Theflow goes through thehose con-
nection inthe reverse direction.
On vehicles withanexcessively highblow-by, the
valve doesnotmeet therequirement. Thisis
because someofthe flow willgothrough the
hose connection tothe intake manifold collector
under allconditions.
This
system returnsblow-by gastothe intake
manifold collector.
The positive crankcase ventilation (peV)valveis
provided toconduct crankcase blow-bygastothe
intake manifold.
During partialthrottle operation ofthe engine, the
intake manifold suckstheblow-by gasthrough
the
pev
valve.
Normally, thecapacity ofthe valve issufficient to
handle anyblow-by andasmall amount ofventi-
lating air.
The ventilating airisthen drawn fromtheairduct

•

SEF127R

Q:

Fresh air
• :Blow-by gas
PCV
valve
operation

Engine notrunning
Cruising
or backfiring
~~ .~
Idling or Acceleration
decelerating or
high load
-~ .~

..

Acceleration
orhigh load
Acceleration
orhigh load
pcv valve
Filter
For
Europe andIsrael, andGA15DE
Cruising
GA16DE exceptforEurope andIsrael
Cruising
EC-31

BASICSERVICE PROCEDURE
Idle Speedllgnition TiminglldleMixtureRatio
Adjustment
PREPARATION
• Make surethatthefollowing partsarein
good order.
(1) Battery
(2) Ignition system
(3) Engine oiland coolant levels
(4) Fuses
(5) ECM harness connector
(6) Vacuum hoses
(7) Airintake system
(Oil filler cap,oillevel gauge, etc.)
(8) Fuel pressure
(9)' Engine compression
(10) Throttle valve
(11) EGR valve operation -For Europe and
Israel andAustralia, andGA15DE M/Tmod-
els
Overall inspection sequence

INSPECTION
(12)
Evaporative emissionsystem
• On models equipped withairconditioner,
checks shouldbecarried outwhile theair
conditioner is"OFF".
• On models equipped withautomatic
transaxle, whenchecking idlespeed, ignition
timing andmixture ratio,checks shouldbe
carried outwhile shiftlever isin
"N"
position.
• When measuring
"CO"
percentage, insert
probe morethan40cm (15.7 in)into tailpipe .•
• Turn offheadlamps, heaterblower, rear
defogger.
• Keep frontwheels pointed straight ahead.
• Make thecheck afterthecooling fanhas
stopped.

Perform diagnostic testmode
1/

(Self-diagnostic results).
Check
&
adjust ignition timing.
Check
&
adjust idlespeed. NG
Repair orreplace.
Check oxygen sensor*1 function.

OK
Check
oxygen sensor*1 har-
ness.
Check CO%.

NG
NG
Repair orreplace harness.
OK Replace oxygensensor*1.
INSPECTION END Check
emission controlparts NGCheck oxygen sensor*1 function. OK
and repair orreplace ifneces-
sary.
*1: Heated oxygen sensor(ForEurope andIsrael, andAustralia AfTmodels)
Oxygen sensor(Except forEurope andIsrael, andAustralia AfTmodels)

EC-35