1995 NISSAN ALMERA N15 sunroof

BODY
&
TRIM
SECTION
BT
CONTENTS
* For seat belt,refer toMA and RSsection.
* For wiring diagrams ofbody electrical systems,refertoEL section.
PRECAUTIONS
2
Service Notice 2
Supplemental RestraintSystem(SRS)"AIR
BAG" (DualAirBag System) 2
Supplemental RestraintSystem(SRS)"AIR
BAG" (Single AirBag System) 2
GENERAL SERViCiNG 3
Clip andFastener
3

BODY END
5

Body Front End
5

Body RearEndandOpener 7
DOOR 11
Front Door 11
Rear Door
12

INSTRUMENT PANEL
13

INTERIOR TRIM 16
Side andFloor Trim
16

Door Trim 22Roof
Trim 24
Trunk RoomTrim 26
Back DoorTrim 27
EXTERIOR 28
SEAT 35
Front Seat
35

Heated Seal... 36
Rear Seat 37
SUNROOF 39
WINDSHIELD ANDWINDOWS 43
Windshield andRear Window 43
Back DoorWindow 44
Rear SideWindow
.45

MIRROR 46
Door Mirror .46
BODY ALIGNMENT 47
Engine Compartment 47
Underbody .49

•

INTERIORTRIM
Roof Trim
REMOVAL -Headlining
4-door sedan

CD
Remove frontandrear seats. Referto"SEAT" fordetails, BT-35.

@
Remove frontandrear seat belts. Referto"SEAT BELTS" inRS section fordetails.

@)
Remove bodysidetrim. Refer to"Side andFloor Trim" fordetails, BT-16.

@
Remove sunroofswitch.(Models equipped withsunroof)

@
Remove sunroofwelt.(Models equipped withsunroof)

@
Remove insidemirror assembly.
([) Remove sunvisors.

@
Remove interiorlampassembly.

@
Remove assistgrips.

@)
Remove clips
@
securing headlining.

@
Remove headlining.

SEC. 264-738-963-964

9
Pawl'
Pawl SBT056
BT-24

INTERIORTRIM
Roof Trim (Cont'd)
REMOVAL -Headlining
3-door and5-door hatchback

CD
Remove frontandrear seats. Referto"SEAT" fordetails, BT-35.

@
Remove frontandrear seat belts. Referto"SEAT BELTS" inRS section fordetails.

@)
Remove bodysidetrim. Refer to"Side andFloor Trim" fordetails, BT-16.

@
Remove sunroofswitch.(Models equipped withsunroof)

cID
Remove sunroofwelt.(Models equipped withsunroof)

@
Remove insidemirror assembly.

(f)
Remove sunvisors.

@
Remove interiorlampassembly.

@
Remove assistgrips.

@)
Remove clips
@
securing headlining.

(j]
Remove roofrear garnish.

@
Remove headlining.

SEC.
264-738-963-964

Pawl
•

Metal
clip
l!1

Pawlm

m
SBT05?
8T-25

EXTERIOR

r
Sunroof rail
assembly

l

SBF349H
Front
Sun
roof lid
weatherstrip
Roof panel
SBT067

@

Door outside molding
Front door

SEC. 800 Screw'
III

~" g.@~

Door outer molding ~__

~/CIiP
~"..-/f'yoor outerpanel

Rear door ~
c:?

SEC. 820
~J

s,,~,~)

\.~ ~' "',,mold'"
CIIP~~

Door panel --~

~ 0

@
Sunroof lidweath .

S
erstnp

EC.736

SBT043
SBF455EA

d;!)de

(\

@

\\
@

\\

@

.........
\
\

@

\\

@

II

@

u

~~

::€t)£j

I.

II

.~) I

:
Front dooronly

CID
Door weatherstrip
SEC. 800.820
@
Body sidewelt

SEC. 769

@
Front doo .
r parting seal
SBT065
8T-30

SUNROOF
ADJUSTMENT Install motor
&
limit SWassembly andsunroof railassembly inthe following sequence:

1. Arrange equallengths oflink and wire assemblies onboth sides ofsunroof opening.
2. Connect sunroofconnector tosunroof switchandpositive
(+)
power supply.
3. Set lidassembly tofully closed position
m
byoperating OPENswitch andTILT switch.
4. Fitouter sideoflid assembly tothe surface ofroof onbody outer panel.
5. Remove motor,andkeep OPEN switch pressed untilmotor pinion gearreaches theend ofits rotat-
ing range.
6. Install motor.
7. Check thatmotor drivegearfitsproperly inwires.
8. Press TILT-UP switchtocheck lidassembly fornormal tilting.
9. Check sunroof lidassembly fornormal operations (tilt-up,tilt-down, open,andclose).

FrontQ
Closing
&
opening range

81-39
ri1

9
Rear

/ Tilting up&down range

- ;:: u~
Outer bodypanel
~ Closing
&
opening range

SBF920F

•

SUNROOF
REMOVAL

• After anyadjustment, checksunroof operation andlidalignment.
• Handle finisher plateandglass lidwith care sonot tocause damage.
• Itis desirable foreasy installation tomark eachpoint before removal.

CAUTION:
Always workwithahelper.

Link andwire
assembly Sunroof
frame
assembly Shade
assembly

~
~

8T-40
Lid
assembly Motorassembly

SUNROOF
* For Wiring Diagram, referto"ELECTRIC SUNROOF" inEL section.
SEC. 736

@Motor assembly @Rear
drainassembly
7 Sunroof switchbracket

81-41
SBT081
•

Linkassembly
MBF493B SUNROOF

m
Using flat-bladed screwdriver, pryshade assembly holder
off rail. Then pullshade assembly forwardtoremove itfrom
rail.
I]IIDisengage pawlsfromrail,then remove window deflector
holder.
mUsing flat-bladed screwdriver, prystopper springoffrail
groove. Thensliderearguide backward toremove itfrom
rail.
mRemove wireandlinkassembly fromrailwhile pushing
link back withflat-bladed screwdriver.,
81-42