1994 JEEP CHEROKEE ECU

INSTALLATION
(1) Remove the plugs from the receiver/drier open-
ings. Install receiver/drier into the condenser.
(2) Install the condenser to the radiator. Tighten
the retaining bolts.
(3) Install the radiator and condenser as an assem-
bly (refer to Group 7, Cooling System for the proper
procedure).
(4) Plug the harness into the low pressure switch
(Fig. 21).
(5) Connect the A/C hoses to the condenser.
(6) Connect the transmission cooler lines (if
equipped with automatic transmission).
(7) Connect the fan shroud and the radiator hoses.
(8) Add 30 ml (1 fluid oz.) of refrigerant oil to the
system if the condenser was replaced.
(9) Fill the cooling system.
(10) Charge the A/C system.
CONDENSERÐ4.0L ENGINES
REMOVAL
(1) Disconnect the fan shroud and electric fan from
the radiator.
(2) Remove the upper crossmember and bracket.
(3) Evacuate the A/C system, disconnect the A/C
hoses from the condenser and plug the openings.
(4) Remove the attaching hardware and brackets
securing the condenser to the radiator.
(5) Remove the condenser.
INSPECTION
When servicing a condenser for a leak at the bot-
tom, inspect the lower crossmember for an ID tag.
This tag may rub against the condenser. If the con-dition exists, remove the tag prior to installing a new
condenser.
INSTALLATION
(1) Install the condenser.
(2) Remove the plugs from the openings. Connect
the A/C hoses to the condenser.
(3) Install the upper crossmember and bracket.
(4) Connect the fan shroud and electric fan to the
radiator.
(5) Add 30 ml (1 fluid oz.) of refrigerant oil to the
A/C system if the condenser was replaced.
(6) Charge the A/C system.
RECEIVER DRIERÐ4.0L ENGINES
REMOVAL
(1) Evacuate the A/C system, disconnect the A/C
hoses from the receiver dryer and plug the openings
(Fig. 22).
(2) Unplug the harness from the low pressure
switch.
(3) Remove the nut attaching the receiver dryer to
the side sill weld stud.
(4) Remove the receiver dryer.
INSTALLATION
(1) Install the receiver dryer.
(2) Install and tighten the nut attaching the re-
ceiver dryer to the side sill weld stud.
(3) Plug the harness to the low pressure switch.
(4) Remove the plugs the openings. Connect the
A/C hoses to the receiver dryer.
(5) Charge the A/C system.
Fig. 21 Condenser Receiver DrierÐ2.5L Engine
Fig. 22 Receiver DryerÐ4.0L Engine
24 - 32 HEATING AND AIR CONDITIONINGJ

HEATER CORE AND HOUSING
REMOVAL
WARNING: HOT ENGINE COOLANT CAN CAUSE
SEVERE BURNS. DO NOT OPEN THE RADIATOR
DRAIN COCK WHEN THE COOLING SYSTEM IS
HOT AND PRESSURIZED. ALLOW THE COOLANT
TO DECREASE TO ROOM TEMPERATURE BEFORE
STARTING REPAIR OPERATIONS.
(1) Drain approximately 1.9 liters (2 qts) of coolant
from the radiator. Drain the coolant into a clean con-
tainer.
(2) Disconnect the heater hoses.
(3) Disconnect the vent door cables.
(4) Disconnect the blower motor wire.
(5) Disconnect the defroster duct.
(6) Remove the nuts that attach the heater hous-
ing studs to the engine compartment side of the dash
panel.
(7) Remove the heater housing assembly by tilting
it downward, to disengage it from the defroster duct.
Pull it rearward and out from under the instrument
panel.
(8) Remove the heater hosing cover from the hous-
ing.
(9) Remove the heater core from the housing.
INSTALLATION
(1) Install the heater core in the housing and in-
stall the cover on the housing.
(2) Position the heater housing on the dash panel.
Be sure the housing studs all extend through the
dash panel.
(3) Install the seals on the heater core outlet and
inlet tubes and over the blower motor housing.
(4) Install the attaching nuts on the housing studs.
CAUTION: DO NOT over tighten the attaching nuts.
The housing could become distorted causing air
leaks and improper heater door operation. Tighten
the nuts alternately and evenly until 2 stud threads
are visible beyond each nut.
(5) Connect the defroster duct to the housing.
(6) Connect the blower motor wire.
(7) Connect the vent door control cables.
(8) Connect the heater hoses.
(9) Fill and bleed the cooling system.
(10) Check system operation.
BLOWER MOTOR (HEATING)
REMOVAL
(1) Remove the heater housing.
(2) Remove the blower motor-to-heater housing at-
taching screws/nuts.
(3) Remove the blower motor from the housing.
INSTALLATION
(1) Position the blower motor into the housing.
(2) Install and tighten the blower motor-to-heater
housing attaching screws/nuts.
(3) Install the heater housing.
(4) Check blower motor and heater operation.
DEFROSTER NOZZLE AND DUCT
REMOVAL
WARNING: HOT ENGINE COOLANT CAN CAUSE
SEVERE BURNS. DO NOT OPEN THE RADIATOR
DRAIN COCK WHEN THE COOLING SYSTEM IS
HOT AND PRESSURIZED. ALLOW THE COOLANT
TO DECREASE TO ROOM TEMPERATURE BEFORE
STARTING REPAIR OPERATIONS.
(1) Drain approximately 1.9 liters (2 qts) of coolant
from the radiator. Drain the coolant into a clean con-
tainer.
(2) Disconnect the heater hoses.
(3) Remove the nuts attaching the heater housing
studs to the engine compartment side of the dash
panel.
(4) Disconnect the speedometer cable.
(5) Remove the glove box.
(6) Tilt the heater housing back and pull it rear-
ward and out from under the instrument panel.
(7) Disconnect the vent control cables.
(8) Remove the fresh air intake grille from the
cowl.
(9) Remove the fresh air intake duct.
(10) Lower the windshield.
(11) Remove the defroster nozzle attaching screws
and remove the nozzle and duct.
INSTALLATION
(1) Install the defroster nozzle and duct.
(2) Raise and secure the windshield.
(3) Install the fresh air intake duct.
(4) Install the fresh air intake grille on the cowl.
(5) Install the vent cables.
(6) Position the heater housing on the dash panel.
Be sure all the housing studs extend through the
dash panel.
(7) Install the seals on the blower motor and the
heater core inlet and outlet tubes.
(8) Install the attaching nuts on the housing studs.
CAUTION: DO NOT over tighten the attaching nuts.
The housing could become distorted causing air
leaks and improper heater door operation. Tighten
the nuts alternately and evenly until 2 stud threads
are visible beyond each nut.
(9) Install the glove box.
(10) Connect the speedometer cable.
(11) Connect the heater hoses.
24 - 40 HEATING AND AIR CONDITIONINGJ

(12) Fill and bleed the cooling system.
FRESH AIR DOOR VACUUM MOTOR
REMOVAL
(1) Remove the glove box and assist handle.
(2) Disconnect the vacuum hose from the motor.
(3) Remove the motor lever retaining clip.
(4) Remove the motor attaching nuts and remove
the motor from the fresh air duct.
INSTALLATION
(1) Position the motor on the fresh air duct and in-
stall the motor attaching nuts.
(2) Align the motor lever with the air door lever
and install the lever retaining clip.
(3) Connect the vacuum hose to the motor.
(4) Install the glove box and assist handle.
FRESH AIR INTAKE DUCT
REMOVAL
WARNING: HOT ENGINE COOLANT CAN CAUSE
SEVERE BURNS. DO NOT OPEN THE RADIATOR
DRAIN COCK WHEN THE COOLING SYSTEM IS
HOT AND PRESSURIZED. ALLOW THE COOLANT
TO DECREASE TO ROOM TEMPERATURE BEFORE
STARTING REPAIR OPERATIONS.
(1) Drain approximately 1.9 liters (2 qts) of coolant
from the radiator. Drain the coolant into a clean con-
tainer.
(2) Disconnect the heater hoses.
(3) Remove the nuts attaching the heater housing
studs to the dash panel from inside the engine com-
partment.
(4) Disconnect the speedometer cable.
(5) Remove the glove box and assist handle.
(6) Tilt the heater housing back and pull it rear-
ward and out from under the instrument panel.
(7) Disconnect the vent cables.
(8) Remove the fresh air intake grille from the
cowl.
(9) Remove the fresh air intake duct.
INSTALLATION
(1) Install the fresh air intake duct.
(2) Install the defroster nozzle and duct.
(3) Raise and secure the windshield.
(4) Install the fresh air grille on the cowl.
(5) Install the vent cables.
(6) Position the heater housing on the dash panel.
Be sure all the housing studs extend through the
dash panel.
(7) Install the seals on the blower motor and
heater core inlet and outlet tubes.
(8) Install the attaching nuts on the heater hous-
ing studs.CAUTION: DO NOT over tighten the attaching nuts.
The housing could become distorted causing air
leaks and improper heater door operation. Tighten
the nuts alternately and evenly until 2 stud threads
are visible beyond each nut.
(9) Install the glove box and assist handle.
(10) Connect the speedometer cable.
(11) Connect the heater hoses.
(12) Fill and bleed the cooling system.
DESCRIPTION (AIR CONDITIONING)
The evaporator, blower fan and motor, thermostat,
expansion valve, capillary tube, air outlets and sys-
tem controls are located in the evaporator housing.
The evaporator housing is mounted under the instru-
ment panel. The compressor, condenser, receiver-
dryer and refrigerant lines are located in the engine
compartment.
A rotary-type compressor with magnetic clutch op-
erated drive pulley is used for all vehicles equipped
with air conditioning.
SIGHT GLASS
A sight glass is located on the top of the receiver-
drier (Fig. 6). The sight glass provides a visual check
of system refrigerant level. A continuous stream of
bubbles will appear in the sight glass when system
charge is low. Bubbles will not appear when the sys-
tem is fully charged.
A/C CONTROL PANEL
FAN SWITCH
The fan switch may be serviced by removing the
access plate located on the lower evaporator core
housing.
TEMPERATURE CONTROL THERMOSTAT
REMOVAL
(1) Lower the evaporator housing.
(2) Remove the attaching screws holding the top
and bottom housings together.
(3) Separate the housings.
(4) Remove the thermostat.
Fig. 6 Sight Glass (Typical)
JHEATING AND AIR CONDITIONING 24 - 41

(6) Lower the evaporator housing and pull the
hoses and hose grommet through the dash opening.
The blower motor, blower motor housing, evapora-
tor core, control switches and expansion valve can all
be serviced after removing the evaporator housing
(Fig. 9).
INSTALLATION
(1) If the evaporator is replaced, add 30 ml (1 fluid
oz.) of refrigerant oil to the system.
(2) Push the hoses through the grommet openings
and install the hose grommet by pushing it toward
the engine compartment.
(3) Install the hose grommet attaching screws.
(4) Raise the evaporator housing. Install the evap-
orator housing-to- instrument panel attaching screws
and the evaporator housing mounting bracket screw.
(5) Install the hose clamps.
(6) Connect the receiver-drier hoses.
(7) Connect the inlet (suction) hose.
(8) Evacuate, charge and leak test the system.
EXPANSION (H) VALVE
REMOVAL
(1) Discharge the system slowly to prevent loss of
compressor oil.
(2) Remove the evaporator housing.
(3) Remove the insulation wrapped around the suc-
tion hose fitting, expansion valve and evaporator
tubing.(4) Mark the capillary tube location on the evapo-
rator tubing.
(5) Disconnect the inlet and outlet hose fittings,
and remove the capillary tube clamp.
(6) Disconnect and remove the expansion valve.
INSTALLATION
(1) Clean the evaporator tubing to provide a posi-
tive metal-to-metal contact for the replacement ex-
pansion valve capillary tube.
(2) Install the replacement expansion valve.
(3) Clamp the capillary tube at the marked loca-
tion on the evaporator tubing.
(4) Connect the inlet and outlet hose fittings.The
capillary tube must be securely clamped and
have positive metal-to-metal contact with the
evaporator tubing.
(5) Wrap the expansion valve, inlet hose fitting
and capillary tube with insulation.
(6) Install the evaporator housing.
(7) Evacuate, charge and leak test the system.
A/C BLOWER MOTOR
It is not necessary to discharge the system to ser-
vice the blower motor. The evaporator housing need
only be lowered for access to the blower motor at-
taching screws.
JHEATING AND AIR CONDITIONING 24 - 43

COMPONENT REMOVAL/INSTALLATION
INDEX
page page
Air Cleaner Housing....................... 8
Air Filter................................ 9
Coolant Temperature Sensor................. 9
EVAP Canister........................... 9Fuel Tank Filler Tube Cap.................. 9
Oxygen (O2S) Sensor...................... 9
Powertrain Control Module (PCM)............. 9
Pressure Relief/Rollover Valve................ 9
AIR CLEANER HOUSING
REMOVAL
(1) Unlock clean air hose clamp (Figs. 3 or 4) at
air cleaner cover. To unlock the clamp, attach adjust-
able pliers to clamp and rotate pliers as shown in fig-
ure 3. Remove clean air hose at cover.
(2) Disconnect vacuum lines at air cleaner hous-
ing.
(3) YJ Models: Release the three over-center type
clamps securing the housing to the housing bracket.
XJ Models: Remove the housing cover and remove
air filter. Remove two bolts and one nut.
(4) Release the air cleaner housing from the ambi-
ent air inlet and remove housing from vehicle.
INSTALLATION
(1) Position air cleaner housing to body and ambi-
ent air inlet.
(2) YJ Models: Lock the three over-center type
clamps securing the housing to the housing bracket.
XJ Models: Install two bolts and one nut to housing.Fig. 3 Air CleanerÐXJ ModelsÐTypical
Fig. 4 Air CleanerÐYJ ModelsÐTypical
Fig. 5 Clamp Removal
25 - 8 EMISSION CONTROL SYSTEMSJ

COLD CRANKING TEST, STARTING
SYSTEM............................8A-9
COLLISION DAMAGE TORQUE.............13-1
COLORS, EXTERIOR BODY..............23-204
COLUMN GENERAL SERVICE, STEERING . . . 19-45
COLUMN, NON-TILT STEERING...........19-50
COLUMN REPLACEMENTÐXJ............19-46
COLUMN REPLACEMENTÐYJ............19-48
COLUMN, TILT STEERING...............19-59
COLUMNÐXJ, STEERING...............19-73
COLUMNÐYJ, STEERING...............19-73
COMBINATION VALVE................5-15,5-42
COMBINATION VALVE REPLACEMENTÐXJ . . . 5-55
COMBINATION VALVE REPLACEMENTÐYJ . . . 5-55
COMBUSTION PRESSURE LEAKAGE
TEST, CYLINDER.......................9-6
COMBUSTION PRESSURE LEAKAGE
TEST DIAGNOSIS, CYLINDER.............9-6
COMPASS REPAIR PROCEDURES..........8C-4
COMPENSATION, CALIPER OPERATION
AND WEAR..........................5-24
COMPRESSION PRESSURE TEST,
CYLINDER............................9-5
COMPRESSOR........................24-17
COMPRESSOR DIAGNOSIS..............24-13
COMPRESSOR ISOLATION...............24-17
COMPRESSOR OF AIR, PURGING.........24-17
COMPRESSOR OIL LEVEL................24-6
COMPRESSOR OVERHAUL...............24-17
COMPRESSOR VALVE PLATEÐLEAK
TESTS..............................24-8
COMPRESSOR/HOSES/FITTINGS, AIR-
CONDITIONER........................0-21
CONDENSERÐ4.0L ENGINES............24-32
CONDENSER, A/C......................24-42
CONDENSER/RECEIVER DRIERÐ2.5L
ENGINES...........................24-31
CONDITION, CHECKING FLUID LEVEL......21-96,
21-173
CONDITION, FLUID LEVEL...............21-69
CONDITIONING CLUTCH RELAY, AIR.......14-54
CONDITIONING CLUTCH RELAYÐPCM
OUTPUT, AIR........................14-24
CONDITIONING CONTROLSÐPCM INPUT,
AIR ...............................14-19
CONDITIONING SCHEMATIC, AIR..........24-25
CONDITIONING SYSTEM DIAGNOSIS,
AIR ...............................24-12
CONDITIONING SYSTEMÐXJ VEHICLES,
AIR ...............................24-14
CONDITIONING SYSTEMÐYJ VEHICLES,
AIR ...............................24-15
CONNECTING ROD BEARING FITTING
CHART..........................9-36,9-76
CONNECTING RODS, PISTONS........9-34,9-74
CONNECTIONS, STARTER RELAY..........8A-12
CONNECTOR AND TERMINAL ASSEMBLY
REPLACEMENT.......................8W-5
CONNECTORÐPCM INPUT, DATA LINK.....14-20
CONNECTORÐPCM OUTPUT, DATA LINK . . . 14-24
CONNECTOR PINS, RADIO................8F-3
CONNECTOR, POWERTRAIN CONTROL
MODULE (PCM) 60-WAY...............14-38
CONNECTOR REPLACEMENT.............8W-4
CONNECTORS.........................8W-3
CONSOLE, OVERHEAD...................8A-1
CONSOLE REPAIR PROCEDURES..........8C-6
CONSOLE SHIFT, DISASSEMBLYÐ
COLUMN OR
........................19-50
CONSOLEÐXJ VEHICLES, FULL FLOOR
. . . 23-125
CONSOLEÐXJ VEHICLES, MINI-FLOOR
....23-124
CONSOLEÐXJ VEHICLES, OVERHEAD
......8L-20
CONSOLES, FLOOR
...................23-197
CONSTRUCTION, XJ UNIBODY
.............13-1
CONTACT PATTERN ANALYSIS,
BACKLASH AND; FRONT SUSPENSION
AND AXLE
...........................2-44
CONTACT PATTERN ANALYSIS, BACKLASH
AND; REAR SUSPENSION AND AXLES
.....3-25
CONTAMINATION, BRAKE FLUID
...........5-13
CONTINUITY TESTS, IGNITION SWITCH
....8D-31
CONTROL AND DISPLAY SYMBOLS,
INTERNATIONAL VEHICLE
...........INTRO.-3
CONTROL AND DISPLAY SYMBOLS,
VEHICLE
.........................INTRO.-7CONTROL CABLE REPLACEMENT,
HEATER ............................24-30
CONTROL CABLES, VENT DOOR..........24-39
CONTROL CIRCUIT TESTS, STARTER......8A-11
CONTROL, FUEL PUMP ELECTRICAL........14-5
CONTROL (IAC) MOTOR, IDLE AIR........14-56
CONTROL (IAC) MOTORÐPCM OUTPUT,
IDLE AIR...........................14-25
CONTROL INFORMATION (VECI)
LABEL, VEHICLE WINDOW..............25-1
CONTROL MODULE, ELECTRICAL TESTS
AT POWERTRAIN.....................8H-6
CONTROL MODULE (PCM) 60-WAY
CONNECTOR, POWERTRAIN............14-38
CONTROL MODULE (PCM), POWERTRAIN;
EMISSION CONTROL SYSTEMS..........25-9
CONTROL MODULE (PCM), POWERTRAIN;
FUEL SYSTEM..................14-18,14-58
CONTROL MODULE (PCM), POWERTRAIN;
IGNITION SYSTEMS.........8D-6,8D-15,8D-28
CONTROL MODULE (TCM) SERVICE,
TRANSMISSION.....................21-173
CONTROL MOTOR TEST, IDLE AIR........14-46
CONTROL PANEL, A/C..................24-41
CONTROL PANEL REPLACEMENT,
HEATER ............................24-39
CONTROL PANEL REPLACEMENT,
HEATER AND A/C ....................24-26
CONTROLÐPCM INPUT, SPEED..........14-23
CONTROLÐPCM OUTPUT, SPEED.........14-27
CONTROL SERVO REPLACEMENT, SPEED....8H-9
CONTROL SWITCH REPLACEMENT,
SPEED..............................8H-9
CONTROL SWITCH REPLACEMENT,
WIPER.............................8K-15
CONTROL SWITCH TEST, STOP LAMP
SPEED..............................8H-7
CONTROL SWITCH (TURN SIGNAL
LEVER) TEST, SPEED..................8H-7
CONTROL SYSTEM ELECTRICAL TESTS,
VEHICLE SPEED......................8H-5
CONTROL SYSTEM, EVAP (EVAPORATION)....25-4
CONTROL SYSTEM, VEHICLE SPEED........8A-1
CONTROL SYSTEMÐXJ VEHICLES,
CLIMATE...........................24-22
CONTROL SYSTEMÐYJ VEHICLES,
CLIMATE...........................24-37
CONTROL THERMOSTAT, TEMPERATURE....24-35
CONTROL UNIT (ECU), ELECTRONIC........5-41
CONTROL UNIT (HCU), HYDRAULIC........5-39
CONTROL VALVE FITTING O-RING SEAL,
FLOW..............................19-12
CONTROLS AND COMPONENTS,
TRANSMISSION......................21-66
CONTROLS, EVAPORATIVE EMISSION.......25-4
CONTROLS, EXHAUST EMISSION..........25-7
CONTROLSÐPCM INPUT, AIR
CONDITIONING (A/C)..................14-19
CONTROLSÐXJ VEHICLES, BLOWER......24-14
CONVERSION FORMULAS AND
EQUIVALENT VALUES..............INTRO.-8
CONVERSION, TORQUE..............INTRO.-10
CONVERTER, CATALYTIC.............11-1,11-5
CONVERTER CLUTCH ENGAGED,
HYDRAULIC FLOW IN THIRD GEAR......21-90
CONVERTER CLUTCH RELAY.............14-60
CONVERTER CLUTCH RELAY TEST........14-45
CONVERTER CLUTCH RELAYÐPCM
OUTPUT............................14-27
CONVERTER HOUSING LEAK
DIAGNOSIS.........................21-73
CONVERTER INSTALLATION,
TRANSMISSION.....................21-109
CONVERTER INSTALLATION,
TRANSMISSION AND TORQUE.........21-190
CONVERTERÐPUMP SEALÐDRIVE
PLATE SERVICE.....................21-109
CONVERTER REMOVAL, TRANSMISSION . . . 21-108
CONVERTER REMOVAL, TRANSMISSION
AND TORQUE......................21-189
CONVERTER STALL TEST
................21-72
CONVERTER STALL TEST, TORQUE
.......21-169
CONVERTER STATOR CLUTCH
INSPECTION, TORQUE
................21-189
CONVERTER, TORQUE; TRANSMISSION
AND TRANSFER CASE
...........21-66,21-158CONVERTER/MUFFLER/TAILPIPE
SUPPORT BRACKETS, CATALYTIC........23-85
COOLANT.............................7-15
COOLANT RESERVE/OVERFLOW
SYSTEM............................7-19
COOLANT ROUTING, SYSTEM..............7-1
COOLANT TEMPERATURE GAUGE..........8E-1
COOLANT TEMPERATURE GAUGE
INOPERATIVE........................8E-3
COOLANT TEMPERATURE INDICATOR
INOPERATIVE........................8E-3
COOLANT TEMPERATURE INDICATOR
LAMP...............................8E-1
COOLANT TEMPERATURE SENSOR.........25-9
COOLANT TEMPERATURE SENSOR,
ENGINE; FUEL SYSTEM................14-55
COOLANT TEMPERATURE SENSOR,
ENGINE; IGNITION SYSTEMS
.......8D-4,8D-22
COOLANT TEMPERATURE SENSORÐ
PCM INPUT, ENGINE
..................14-21
COOLANT TEMPERATURE SENSOR TEST,
ENGINE; FUEL SYSTEM
................14-43
COOLANT TEMPERATURE SENSOR TEST,
ENGINE; IGNITION SYSTEMS
...........8D-12
COOLER FLOW TESTING, TRANSMISSION
. . 21-106
COOLER LINE FITTINGS, TRANSMISSION
. . 21-187
COOLER LINES AND FITTINGS,
SERVICING TRANSMISSION
...........21-106
COOLER REVERSE FLUSHING,
TRANSMISSION
.....................21-105
COOLER SERVICE, TRANSMISSION
.......21-187
COOLERS, TRANSMISSION OIL
............7-29
COOLING SYSTEM; COOLING SYSTEM
.......7-1
COOLING SYSTEM; LUBRICATION AND
MAINTENANCE
.......................0-16
COOLING SYSTEM CAPACITIES
............7-38
COOLING SYSTEM CLEANING/REVERSE
FLUSHING
...........................7-17
COOLING SYSTEM COMPONENTS
...........7-1
COOLING SYSTEM, DRAINING
.............7-16
COOLING SYSTEM FANS
.................7-26
COOLING SYSTEM FOR LEAKS, TESTING
....7-18
COOLING SYSTEM HOSES
................7-26
COOLING SYSTEM, REFILLING
............7-17
CORE AND HOUSING, HEATER
............24-40
CORE, HEATER
........................24-28
CORE HOUSING REPLACEMENT, HEATER
. . . 24-29
COVER AND DISC INSTALLATION,
CLUTCH
.............................6-10
COVER AND DISC REMOVAL, CLUTCH
......6-10
COVER AND FRAME, BUCKET SEATBACK
. . 23-100
COVER, BUCKET SEAT CUSHION
..........23-98
COVER, ENGINE CYLINDER HEAD
......9-18,9-59
COVER, FRAME CROSSMEMBER
..........13-14
COVER OIL SEAL REPLACEMENT,
TIMING CASE
....................9-26,9-67
COVER REPLACEMENT, PITMAN SHAFT
AND SIDE
..........................19-26
COVER, TIMING CASE
...............9-27,9-67
COVERÐXJ VEHICLES, REAR SEAT
CUSHION
..........................23-107
COVERÐXJ VEHICLES, REAR
SEATBACK
.........................23-111
COVERSÐXJ VEHICLES, B/C-PILLAR AND
LIFTGATE PILLAR TRIM
..............23-116
COWL GRILLE AND SCREEN
.......23-11,23-139
COWL WEATHERSTRIP SEAL
............23-139
COWL WEATHERSTRIP SEAL/
CROSSMEMBER AIR DEFLECTOR
........23-10
CRANKCASE VENTILATION SYSTEM;
EMISSION CONTROL SYSTEMS
..........25-5
CRANKCASE VENTILATION SYSTEM;
LUBRICATION AND MAINTENANCE
........0-17
CRANKING TEST, STARTING SYSTEM
COLD
...............................8A-9
CRANKSHAFT MAIN BEARINGS;
ENGINES
........................9-40,9-80
CRANKSHAFT POSITION SENSOR;
FUEL SYSTEM
.......................14-55
CRANKSHAFT POSITION SENSOR;
IGNITION SYSTEMS
..............8D-2,8D-21
JINDEX5
Description Group-Page Description Group-Page Description Group-Page

CRANKSHAFT POSITION SENSORÐPCM
INPUT.............................14-20
CRANKSHAFT POSITION SENSOR TEST;
FUEL SYSTEM.......................14-44
CRANKSHAFT POSITION SENSOR TEST;
IGNITION SYSTEMS...................8D-9
CROSSMEMBER COVER, FRAME..........13-14
CROSSMEMBER, RADIATOR SUPPORT......23-5
CUSHION AND COVER, BUCKET SEAT......23-98
CUSHION COVERÐXJ VEHICLES, REAR
SEAT .............................23-107
CUSHION, ENGINE FRONT SUPPORT.......13-15
CUSHION RECONDITIONINGÐXJ
VEHICLES, REAR SEAT...............23-108
CUSHIONÐXJ VEHICLES, REAR SEAT.....23-107
CYLINDER BLOCK..................9-45,9-85
CYLINDER BORES, HONING................9-2
CYLINDER COMBUSTION PRESSURE
LEAKAGE TEST DIAGNOSIS...........9-5,9-6
CYLINDER DISPOSAL, LIFTGATE
SUPPORT ROD......................23-70
CYLINDER, DOOR KEY LOCK.............23-54
CYLINDER ENGINE, VACUUM ROUTING
SCHEMATICÐ2.5L 4...................25-2
CYLINDER ENGINE, VACUUM ROUTING
SCHEMATICÐ4.0L 6...................25-3
CYLINDER, FULL-METAL DOOR KEY
LOCK.............................23-178
CYLINDER HEAD COVER, ENGINE......9-18,9-59
CYLINDER HEAD, ENGINE............9-19,9-60
CYLINDER HEAD GASKET FAILURE
DIAGNOSIS, ENGINE....................9-5
CYLINDER INSTALLATION, MASTER....5-20,5-50
CYLINDER INSTALLATION, WHEEL.........5-37
CYLINDER, LIFTGATE SUPPORT ROD......23-69
CYLINDER, MASTER.....................5-40
CYLINDER OVERHAUL, WHEEL............5-36
CYLINDER OVERHAUL, MASTER...........5-20
CYLINDER REMOVAL, MASTER........5-20,5-50
CYLINDER REMOVAL, WHEEL.............5-36
CYLINDER REPLACEMENT, LIFTGATE
LOCK...............................8P-7
CYLINDER, STANDARD MASTER...........5-20
CYLINDER, TAILGATE LOCK.............23-160
CYLINDER/POWER BOOSTER TEST,
MASTER............................5-11
CYLINDER/STRIKER, LIFTGATE LATCH/
KEY LOCK..........................23-68
CYLINDERS, KEY LOCK............23-2,23-132
D RANGE FIRST GEAR, HYDRAULIC
FLOW IN...........................21-87
D RANGE SECOND GEAR, HYDRAULIC
FLOW IN...........................21-88
D RANGE THIRD GEAR, HYDRAULIC
FLOW IN...........................21-89
DAMAGE TORQUE, COLLISION............13-1
DAMAGED OR WORN THREADS, REPAIR.....9-4
DAMPENER, STEERING............19-15,19-18
DAMPER, ENGINE......................9-13
DAMPER, VIBRATION................9-26,9-67
DASH PANEL INSULATION PANEL.........23-95
DASH PANEL INSULATOR PANEL.........23-11
DATA LINK CONNECTORÐPCM INPUT.....14-20
DATA LINK CONNECTORÐPCM OUTPUT....14-24
DATA, VEHICLE DIMENSION . . . INTRO.-3,INTRO.-4
DATA, VEHICLE LOAD................INTRO.-3
DATA, XJ VEHICLE LOAD.............INTRO.-5
DATA, YJ-VEHICLE LOAD.............INTRO.-6
DAYTIME RUNNING LIGHTS (CANADA
ONLY) .............................8L-16
DECODING, VEHICLE CODE...........INTRO.-3
DECODING, VEHICLE IDENTIFICATION
NUMBER (VIN)....................INTRO.-2
DEFLECTOR, COWL WEATHERSTRIP
SEAL/CROSSMEMBER AIR.............23-10
DEFOGGER GRID REPAIR, REAR
WINDOW............................8N-2
DEFOGGER GRID TEST, REAR
WINDOW............................8N-1
DEFOGGER, REAR WINDOW..............8A-1
DEFOGGER RELAY, REAR
................8N-4
DEFOGGER SWITCH REPLACEMENT,
REAR WINDOW
.......................8N-4
DEFOGGER/FOG LAMP/REAR WIPER
SWITCHES, REAR
....................8E-21
DEFROSTER DUCT REPLACEMENT
........24-29DEFROSTER NOZZLE AND DUCT..........24-40
DELAY FUNCTION TROUBLE
DIAGNOSISÐXJ VEHICLES, HEADLAMP . . . 8L-16
DELAY MODULE REPLACEMENTÐXJ
VEHICLES, HEADLAMP................8L-16
DELAY MODULEÐXJ VEHICLES,
SENTINEL HEADLAMP.................8L-15
DELIVERY SYSTEM, FUEL................14-2
DEPTH INFORMATION, PINION GEAR;
FRONT SUSPENSION AND AXLE..........2-37
DEPTH INFORMATION, PINION GEAR;
REAR SUSPENSION AND AXLES..........3-19
DEPTH VARIANCE, PINION GEAR; FRONT
SUSPENSION AND AXLE................2-38
DEPTH VARIANCE, PINION GEAR; REAR
SUSPENSION AND AXLES...........3-20,3-38
DESCRIPTION (AIR CONDITIONING).......24-41
DESCRIPTION; AUDIO SYSTEMS...........8F-1
DESCRIPTION (HEATING)................24-37
DESCRIPTION; HEATING AND AIR
CONDITIONING.................24-17,24-22
DESCRIPTION; OVERHEAD CONSOLE.......8C-1
DESCRIPTION; POWER DOOR LOCKS.......8P-1
DESCRIPTION; POWER WINDOWS.........8S-1
DESCRIPTION; TRANSMISSION AND
TRANSFER CASE....................21-156
DESCRIPTION; TURN SIGNALS AND
HAZARD WARNING FLASHER........8J-1,8J-2
DESCRIPTION/SYSTEM OPERATION,
MULTI-PORT FUEL INJECTION (MFI)Ð
COMPONENT........................14-17
DESIGNATION CODES, VEHICLE........INTRO.-1
DESIGNATIONS, LABELS/PLATES, CODES
AND DIMENSIONS.................INTRO.-1
DESIGNATIONS, VEHICLE.............INTRO.-1
DETECTION AND REPAIR, FIXED GLASS
WATER LEAK..................23-83,23-189
DIAGNOSING INTERMITTENT
WINDSHIELD WASHER................8K-12
DIAGNOSING NON-INTERMITTENT
WINDSHIELD WASHER................8K-12
DIAGNOSING PARKING BRAKE
PROBLEMS..........................5-10
DIAGNOSING POWER DOOR LOCKS....8P-1,8P-9
DIAGNOSING REAR WIPER...............8K-6
DIAGNOSING REAR WIPER WASHER.......8K-6
DIAGNOSING REAR WIPER/WASHER......8K-14
DIAGNOSING SERVICE BRAKE
PROBLEMS...........................5-8
DIAGNOSING WINDSHIELD WASHER
(INTERMITTENT)......................8K-4
DIAGNOSING WINDSHIELD WASHER
(NON-INTERMITTENT)..................8K-4
DIAGNOSING WINDSHIELD WIPERS . . . 8K-3,8K-11
DIAGNOSINGÐALL LAMPS OUT..........8E-16
DIAGNOSINGÐTURN SIGNAL
INOPERATIVE.........................8J-2
DIAGNOSIS, 2.5L STARTER MOTOR NOISE . . . 8A-13
DIAGNOSIS, 30RH/32RH TRANSMISSION . . 21-69,
21-77,21-78,21-79,21-80,21-81,21-82,21-83,21-84,
21-85
DIAGNOSIS, ABS BRAKE..................5-3
DIAGNOSIS, ABS FAULT................5-4,5-6
DIAGNOSIS, AIR CONDITIONING
SYSTEM............................24-12
DIAGNOSIS AND REPAIR............8G-1,8G-2
DIAGNOSIS; AUDIO SYSTEMS.............8F-1
DIAGNOSIS, AW-4 TRANSMISSION
.......21-167
DIAGNOSIS, AXLE NOISE/VIBRATION;
FRONT SUSPENSION AND AXLE
..........2-16
DIAGNOSIS, AXLE NOISE/VIBRATION;
REAR SUSPENSION AND AXLES
..........3-7
DIAGNOSIS, BELT
.......................7-31
DIAGNOSIS CHARTS, INSPECTION
..........6-4
DIAGNOSIS; CHIME/BUZZER WARNING
SYSTEMS
...........................8U-1
DIAGNOSIS, CLUTCH
.....................6-3
DIAGNOSIS, COMPRESSOR
..............24-13
DIAGNOSIS, CONVERTER HOUSING
LEAK
..............................21-73
DIAGNOSIS; COOLING SYSTEM
.............7-4
DIAGNOSIS, CYLINDER COMBUSTION
PRESSURE LEAKAGE TEST
...............9-6
DIAGNOSIS, DISCONNECT AXLE/SHIFT
MOTOR
.............................2-27DIAGNOSIS, DOME/COURTESY LAMP
TROUBLE...........................8L-19
DIAGNOSIS, ECU........................5-4
DIAGNOSISÐELECTRICAL, SERVICE.......24-14
DIAGNOSIS, ENGINE.....................9-5
DIAGNOSIS, ENGINE CYLINDER HEAD
GASKET FAILURE......................9-5
DIAGNOSIS, EXHAUST SYSTEM............11-2
DIAGNOSIS, FOG LAMP TROUBLE.........8L-12
DIAGNOSIS, GAUGE PACKAGE............8E-22
DIAGNOSIS, GEAR LEAKAGE..............19-8
DIAGNOSIS GUIDES AND CHARTS........21-76
DIAGNOSISÐHAZARD LAMPS
INOPERATIVE.....................8J-1,8J-2
DIAGNOSIS, HCU........................5-4
DIAGNOSIS, HEATING SYSTEM...........24-11
DIAGNOSIS, IGNITION OFF DRAW (IOD).....8A-8
DIAGNOSIS, IGNITION SECONDARY
CIRCUIT...........................8D-12
DIAGNOSIS, ILLUMINATED ENTRY
SYSTEM TROUBLE..............8L-21,8L-22
DIAGNOSIS INFORMATION, GENERAL;
CLUTCH..............................6-3
DIAGNOSIS INFORMATION, GENERAL;
TRANSMISSION AND TRANSFER
CASE.............................21-167
DIAGNOSIS, INSTRUMENT CLUSTER;
INSTRUMENT PANEL AND
GAUGESÐXJ.........................8E-3
DIAGNOSIS, INSTRUMENT CLUSTER;
INSTRUMENT PANEL AND
GAUGESÐYJ........................8E-14
DIAGNOSIS, INTAKE MANIFOLD LEAKAGE.....9-5
DIAGNOSIS, LIGHTED VANITY MIRROR
TROUBLE...........................8L-19
DIAGNOSIS, MANUAL STEERING
SYSTEM............................19-36
DIAGNOSISÐMECHANICAL, SERVICE;
ENGINES.............................9-8
DIAGNOSISÐMECHANICAL, SERVICE;
HEATING AND AIR CONDITIONING........24-8
DIAGNOSIS, MULTI-PORT FUEL
INJECTION (MFI)ÐGENERAL...........14-32
DIAGNOSIS, NOISE.....................3-45
DIAGNOSIS, NP231 SERVICE............21-274
DIAGNOSIS, NP242 SERVICE............21-295
DIAGNOSIS, PERFORMANCE.............24-10
DIAGNOSIS; POWER MIRRORS............8T-1
DIAGNOSIS; POWER SEATS..............8R-1
DIAGNOSIS, POWER STEERING SYSTEM....19-3,
19-4,19-5,19-6,19-7
DIAGNOSIS, PRELIMINARY..............21-69
DIAGNOSIS, PRESSURE..................24-9
DIAGNOSIS PROCEDURES; BRAKES......5-3,5-7
DIAGNOSIS, PUMP LEAKAGE..............19-8
DIAGNOSIS, RADIO NOISE................8F-2
DIAGNOSIS; REAR WINDOW DEFOGGER....8N-2
DIAGNOSIS, SERPENTINE DRIVE BELT......7-32
DIAGNOSIS, SERVICE BRAKE..............5-7
DIAGNOSIS, SERVICE; FRONT
SUSPENSION AND AXLE................2-18
DIAGNOSIS, SERVICE; REAR
SUSPENSION AND AXLES................3-9
DIAGNOSIS, SERVICE; TRANSMISSION
AND TRANSFER CASE . 21-2,21-33,21-171,21-172
DIAGNOSIS, SPRING AND SHOCK;
FRONT SUSPENSIONAND AXLE
......2-12,2-14
DIAGNOSIS, SPRING AND SHOCK; REAR
SUSPENSIONAND AXLES
.............3-3,3-5
DIAGNOSIS, STARTING SYSTEM
..........8A-10
DIAGNOSIS; STEERING
.................19-35
DIAGNOSIS, SUSPENSION AND
STEERING SYSTEM
.....................2-7
DIAGNOSIS, SYSTEM
.....................7-7
DIAGNOSISÐTURN SIGNAL
INOPERATIVE
.........................8J-1
DIAGNOSISÐVEHICLE RUNS ROUGH
AND/OR HAS A MISS, INJECTOR
........14-49
DIAGNOSIS, VIBRATION
.............22-9,22-10
DIAGNOSISÐXJ VEHICLES, HEADLAMP
DELAY FUNCTION TROUBLE
............8L-16
DIAGNOSISÐXJ VEHICLES, HEADLAMP
TROUBLE
............................8L-1
DIAGNOSISÐYJ VEHICLES,
HEADLAMP TROUBLE
..................8L-2
6 INDEXJ
Description Group-Page Description Group-Page Description Group-Page

DRIVE GEAR, SPEED SENSOR ROTORÐ
SPEEDOMETER.....................21-183
DRIVE, GENERATOR REPLACEMENTÐ
LEFT HAND..........................8B-7
DRIVE, GENERATOR
REPLACEMENTÐRIGHT HAND...........8B-9
DRIVE PULLEY REPLACEMENT...........19-11
DRIVE (RHD), BELT TENSIONÐEXCEPT
RIGHT HAND.........................7-33
DRIVE (RHD), BELT TENSIONÐRIGHT
HAND...............................7-34
DRIVE SHAFTS.........................0-27
DRIVE VEHICLES, RIGHT HAND............23-1
DRIVE, WASHER PUMP REPLACEMENTÐ
LEFT HAND..........................8K-2
DRIVE, WASHER PUMP REPLACEMENTÐ
RIGHT HAND.........................8K-3
DRIVELINE SNAP; FRONT SUSPENSION
AND AXLE...........................2-17
DRIVELINE SNAP; REAR SUSPENSION
AND AXLES...........................3-8
DRIVELINE VIBRATION...................16-3
DRIVER SIDE..........................8R-2
DRIVERS DOOR POWER LOCK SWITCHÐ
2-DOOR LEFT HAND DRIVE.............8P-2
DRIVERS DOOR POWER LOCK SWITCHÐ
2-DOOR RIGHT HAND DRIVE............8P-3
DRIVERS DOOR POWER LOCK SWITCHÐ
4-DOOR.............................8P-4
DRIVERS DOOR POWER WINDOW
SWITCHÐ2-DOOR LEFT HAND DRIVE.....8S-6
DRIVERS DOOR POWER WINDOW
SWITCHÐ2-DOOR RIGHT HAND DRIVE....8S-7
DRIVERS DOOR POWER WINDOW
SWITCHÐ4-DOOR....................8S-5
DRIVETRAIN...........................0-22
DRL MODULE REPLACEMENT............8L-16
DRUM BRAKE ADJUSTMENT..............5-35
DRUM BRAKES........................5-34
DRUM BRAKESHOE INSTALLATION.........5-34
DRUM BRAKESHOE REMOVAL.............5-34
DRUM REFINISHING, BRAKE..............5-37
DRUMÐREAR SUPPORT OVERHAUL,
OVERRUNNING CLUTCHÐLOW-
REVERSE..........................21-118
DUCT, DEFROSTER NOZZLE..............24-40
DUCT, FRESH AIR INTAKE...............24-41
DUCT REPLACEMENT, DEFROSTER........24-29
DUCTS/HOSES/TUBING, RUBBER AND
PLASTIC............................0-19
ECU DIAGNOSIS.........................5-4
ECU OPERATION.......................5-46
ECU REPLACEMENTÐXJ.................5-53
ECU REPLACEMENTÐYJ.................5-53
EDGE GUARD/EDGE PROTECTOR STRIP,
DOOR.............................23-61
ELECTRICAL CIRCUITS, ABS SYSTEM
WIRING..............................5-4
ELECTRICAL CONTROL, FUEL PUMP........14-5
ELECTRICAL TESTS AT POWERTRAIN
CONTROL MODULE...................8H-6
ELECTRICAL TESTS AT SERVO............8H-5
ELECTRICAL TESTS, VEHICLE SPEED
CONTROL SYSTEM....................8H-5
ELECTRONIC CONTROL UNIT (ECU)........5-41
ELEMENT, ENGINE AIR CLEANER FILTER....0-16
ELEMENT TEST, OXYGEN SENSOR (O2S)
HEATING...........................14-45
EMISSION CONTROL INFORMATION
(VECI) LABEL, VEHICLE.................25-1
EMISSION CONTROLS, EVAPORATIVE.......25-4
EMISSION CONTROLS, EXHAUST..........25-7
EMR LAMPÐPCM OUTPUT..............14-24
END PLUG, HOUSING...................19-26
ENGINE ACCESSORY DRIVE BELTS.........7-31
ENGINE AIR CLEANER FILTER ELEMENT.....0-16
ENGINE AND TRANSMISSION/TRANSFER
CASE IDENTIFICATION..............INTRO.-3
ENGINE ASSEMBLY (SHORT BLOCK),
SERVICE.............................9-4
ENGINE ASSEMBLYÐXJ VEHICLES;
ENGINES
........................9-14,9-54
ENGINE ASSEMBLYÐYJ VEHICLES;
ENGINES
........................9-16,9-57
ENGINE BLOCK HEATER
..................7-37
ENGINE BREAK-IN
......................0-13ENGINE COOLANT TEMPERATURE
SENSOR; FUEL SYSTEM...............14-55
ENGINE COOLANT TEMPERATURE
SENSOR; IGNITION SYSTEMS......8D-4,8D-22
ENGINE COOLANT TEMPERATURE
SENSORÐPCM INPUT................14-21
ENGINE COOLANT TEMPERATURE
SENSOR TEST; FUEL SYSTEM..........14-43
ENGINE COOLANT TEMPERATURE
SENSOR TEST; IGNITION SYSTEMS......8D-12
ENGINE CYLINDER HEAD.............9-19,9-60
ENGINE CYLINDER HEAD COVER......9-18,9-59
ENGINE CYLINDER HEAD GASKET
FAILURE DIAGNOSIS....................9-5
ENGINE DAMPER.......................9-13
ENGINE DIAGNOSIS......................9-5
ENGINE, ENGINE EXHAUST MANIFOLDÐ
2.5L................................11-7
ENGINE, ENGINE EXHAUST MANIFOLDÐ
4.0L................................11-7
ENGINE, ENGINE FIRING ORDERÐ2.5L....8D-33
ENGINE, ENGINE FIRING ORDERÐ4.0L....8D-33
ENGINE EXHAUST MANIFOLDÐ2.5L
ENGINE.............................11-7
ENGINE EXHAUST MANIFOLDÐ4.0L
ENGINE.............................11-7
ENGINE FIRING ORDERÐ2.5L ENGINE.....8D-33
ENGINE FIRING ORDERÐ4.0L ENGINE.....8D-33
ENGINE FRONT SUPPORT CUSHION.......13-15
ENGINE, INTAKE MANIFOLDÐ2.5L.........11-8
ENGINE, INTAKE MANIFOLDÐ4.0L.........11-9
ENGINE MAINTENANCE..................0-13
ENGINE MOUNTÐREAR.............9-12,9-52
ENGINE MOUNTSÐFRONT...........9-10,9-51
ENGINE OIL...........................0-13
ENGINE OIL CHANGE AND FILTER
REPLACEMENT.......................0-15
ENGINE OIL FILTER.....................0-14
ENGINE ONLY, POWER STEERING
PRESSURE SWITCHÐ2.5L.............14-58
ENGINE PERFORMANCE...................9-2
ENGINE SERVICE PROCEDURES, 2.5L........9-9
ENGINE SERVICE PROCEDURES, 4.0L.......9-50
ENGINE SPECIFICATIONS....9-47,9-87,9-48,9-49,
9-88,9-89
ENGINE STARTER MOTOR SERVICE
PROCEDURES........................8B-4
ENGINE STARTER MOTOR TEST
PROCEDURES ON VEHICLE.............8A-9
ENGINE SUPPORTS.....................0-20
ENGINE, VACUUM ROUTING
SCHEMATICÐ2.5L 4 CYLINDER..........25-2
ENGINE, VACUUM ROUTING
SCHEMATICÐ4.0L 6 CYLINDER..........25-3
ENGINES, 2.5L........................8B-11
ENGINES, 4.0L........................8B-11
ENGINES, CONDENSERÐ4.0L............24-32
ENGINES, CONDENSER/RECEIVER
DRIERÐ2.5L........................24-31
ENGINES, FUEL USAGE STATEMENTÐ
GAS................................0-17
ENGINES, RECEIVER DRIERÐ4.0L........24-32
ENTRY, KEYLESS.......................8P-8
ENTRY SYSTEM SERVICE INFORMATION,
ILLUMINATED.......................8L-20
ENTRY SYSTEM TROUBLE DIAGNOSIS,
ILLUMINATED..................8L-21,8L-22
EQUIVALENT VALUES, CONVERSION
FORMULAS......................INTRO.-8
EVACUATION, SYSTEM...................24-4
EVAP CANISTER....................25-4,25-9
EVAP (EVAPORATION) CONTROL SYSTEM
....25-4
EVAPORATIVE EMISSION CONTROLS
.......25-4
EVAPORATOR AND HOUSING
.............24-42
EVAPORATOR COIL
....................24-34
EVAPORATOR/BLOWER HOUSING
.........24-33
EXHAUST EMISSION CONTROLS
...........25-7
EXHAUST GRILLEÐXJ VEHICLES, AIR
.....23-30
EXHAUST HEAT SHIELDS
.................11-1
EXHAUST MANIFOLDÐ2.5L ENGINE,
ENGINE
.............................11-7
EXHAUST MANIFOLDÐ4.0L ENGINE,
ENGINE
.............................11-7
EXHAUST PIPEÐXJ VEHICLES
............11-3
EXHAUST PIPEÐYJ VEHICLES
............11-4EXHAUST SYSTEM; EXHAUST SYSTEM
AND INTAKE MANIFOLD................11-1
EXHAUST SYSTEM; LUBRICATION AND
MAINTENANCE.......................0-20
EXHAUST SYSTEM DIAGNOSIS............11-2
EXHAUST TAILPIPEÐXJ VEHICLES,
MUFFLER............................11-5
EXHAUST TAILPIPEÐYJ VEHICLES,
MUFFLER............................11-6
EXPANSION (H) VALVE.............24-35,24-43
EXTENDED IDLE SWITCHÐPCM INPUT....14-21
EXTENDED IDLE SWITCH TEST...........14-45
EXTENSION PANELÐYJ RENEGADE
VEHICLES, FRONT FENDER............23-149
EXTENSION PANELÐYJ RENEGADE
VEHICLES, REAR QUARTER...........23-151
EXTENSION PANELÐYJ RENEGADE
VEHICLES, ROCKER.................23-150
EXTENSION PANELS AND FASCIASÐYJ
RENEGADE VEHICLES, BODY..........23-147
EXTENSIONÐXJ VEHICLES, QUARTER
TRIM PANEL.......................23-115
EXTERIOR BODY COLORS..............23-204
EXTERIOR COMPONENTS..........23-3,23-134
EXTERIOR LAMPS......................8L-1
EXTERIOR LAMPS, XJ..................8L-23
EXTERIOR LAMPS, YJ..................8L-23
EXTERIOR MOULDINGS, DOOR WINDOW . . . 23-61
EXTERIOR NAMEPLATES................23-30
EXTERIOR NAMEPLATES (ADHESIVE-
BACKED)..........................23-158
EXTERIOR PAINT CODES, XJ............23-205
EXTERIOR PAINT CODES, YJ............23-206
EXTERNAL HANDLE, DOOR..............23-55
EXTERNAL MIRRORS...................23-31
EXTERNAL RELEASE HANDLE, FULL-
METAL DOOR LATCH.................23-178
EXTERNAL SPARE/WHEEL TIRE CARRIER . . 23-172
EYE BUSHING REPLACEMENT, LEAF
SPRING; FRONT SUSPENSION
AND AXLE...........................2-15
EYE BUSHING REPLACEMENT, LEAF
SPRING; REAR SUSPENSION
AND AXLES........................3-4,3-6
FAILURE DIAGNOSIS, ENGINE CYLINDER
HEAD GASKET.........................9-5
FAN RELAYÐPCM OUTPUT, RADIATOR.....14-26
FANS, COOLING SYSTEM.................7-26
FASCIA AND SKID PLATEÐYJ
RENEGADE VEHICLES, FRONT.........23-148
FASCIA AND SKID PLATEÐYJ
RENEGADE VEHICLES, REAR..........23-152
FASCIASÐYJ RENEGADE VEHICLES,
BODY EXTENSION PANELS............23-147
FAULT DIAGNOSIS, ABS................5-4,5-6
FEED CIRCUIT TESTS - (VOLTAGE DROP
METHOD), STARTER...................8A-9
FENDER EXTENSION PANELÐYJ
RENEGADE VEHICLES, FRONT.........23-149
FENDER FLARE.......................23-144
FENDER, FRONT.......................23-14
FENDER INNER SPLASH SHIELDS........23-147
FENDER SPLASH APRONS..............23-147
FENDERS...........................23-141
FIELDÐPCM OUTPUT, GENERATOR.......14-25
FILL LEVEL, TRANSFER CASE...........21-294
FILLER DOOR BUMPERS, FUEL...........23-31
FILLER HOSE SPLASH SHIELDÐXJ
VEHICLES, FUEL.....................23-86
FILLER NOZZLE/TUBE, FUEL
.............23-30
FILLER PROTECTOR/NOZZLE, FUEL
.......23-158
FILLER TUBE CAP, FUEL TANK;
EMISSION CONTROL SYSTEMS
......25-4,25-9
FILLER TUBE CAP, FUEL TANK; FUEL
SYSTEM
............................14-12
FILLER TUBE, NO-LEAD FUEL TANK
.......14-12
FILTER, AIR; EMISSION CONTROL
SYSTEMS
...........................25-9
FILTER, AIR; FUEL SYSTEM
..............14-54
FILTER BRACKET, FUEL
.................23-86
FILTER ELEMENT, ENGINE AIR CLEANER
....0-16
FILTER, ENGINE OIL
.....................0-14
FILTER, FUEL
.....................14-8,14-55
FILTER REPLACEMENT, ENGINE
OIL CHANGE
.........................0-15
8 INDEXJ
Description Group-Page Description Group-Page Description Group-Page