1994 HONDA INTEGRA Bearing

Intermediate Shaft
Reassembly (cont'dl
'1. Press the intermediate shaft bearing into the bear-ing support using the special tools and a press asshown.
ATTACHMENT,52x55mm07716 - 001o/UX)
Seat the internal circlip in the groove of the bearing
suoDon.
CAUTION: Install the circlip with the tapersd endfacing out.
Press the intermediate shaft into the shaft bearinqusing the specialtools and a press.
Pross
I
16-14
Seat the external circlip in the groove of the inter-
mediate shaft.
NOTE: Installthe circlip with the tapered end facing
our.
Install the outer seal into the bearing support usingthe special tools as shown.
NOTE: Install the seal flush with the bearing sup-port.
DRIVER07749 - 00t(xD0
Pack the interiorol the olter seal.2.0 - 3.5 g 10,07 - 0.12 o2l
OUTER SEAL
ATTACHMENT,aO x 5{) mm l.D.07LAD - PW50601
lnstall the new set ring in the intermediate shaftgroove.

Steering Column
lnspection
Check the steering column ball bearing and steeringjoint bearings for play and proper movement.
lf there is noise or excessive play, replace the joint orcolumn assembly.
Check the retaining collar for damage.
lf it is damaged, replace the retaining collar.
COI-UMN BALLEEARINGSTEERING JOINTBEARINGS
RETAINING COLLAR
Check the absorbing plates, absorbing plate guides
and sliding capsules for distonion or breakage.
Replace them as an assembly if they are distoned orbroken.
ABSONBING
SLIDING CAPSULEThis part is attachedto the column bracketwith the plastic injections.
17-30
Check the tilt mechanism for proper movement andoamage.
- Attach a spring scale to the knob of the tilt lever.Measure the preload required to move the lever.
Pr6load: 70 - 90 N 17 - 9 kgt, 15 - 20 tbf)
- lf the preload measured is not within the sDecifica-tion. remove the 6 mm bolt and stoDDer.
Adjust the preload by retightening the rilt tock boltuntil the correct force can be obtained.- Reinstall the stopper and 6 mm bolt and recheck
the Dreload.
9.8 N'm {1.0 kgt.m,7.2lbt'ftl
TILT LOCK BOLT

Remov€ the circlip, then remove the drive shaft
assembly from the pump housing using a plastic
namm€r.
Remove the seal spacer and oil seal.
Inspect the pump housing for damage on the seal-
ing surfaces.
/-clRcLlP
Q'/
ra -,"
DRIVE SHAFTfor bend,damage or wear,
PUMP HOUSING
11. lnspect the bearing by rotating the outar race slow-
ly. lf any play or roughness is felt, replace the bear-
ing.
Remove and discard the bearing using the
tool and a gress.
Pra3s
+
special
13.Install the new bearing
press.
I{UB DIS/ASSEMBLY BASE07GAF - SD40700
using the special tool and a
Press
+
Installwith thered shielded sidelacing down.
07GAF - SDis)700NOTE: Support the inner racewith the tool securely.
17-39

20.Apply vinyl tape to the pinion shaft.
Separate the valve housing from the pinion shafv
valve using a press.
VALVE HOUSING
Vinyl t.p.
Check the inner wall of the valve housing where the
seal ring slides with your finger. lf there is a step in
the wall, the valve housing is worn. Replace the
valve housing.
NOTE:
There may be the sliding marks from the seal
ring on the wall of the valve housing. Replace
the valve housing only the wall is stepped.
When the valve housing is replaced, install new
32 mm shim(s) on the bearing surface of the
housing to adjust the thickness.
21.
22.
23. Check fo. wear. burrs and other damage to the
edges of the grooves in the sleeve.
NOTE: The pinion shaft and sleeve are a precision
matched set. It either the pinion shaft or sleeve
must be replaced, replace the both parts as a set.
SLEEVE SEAL RINGSCh6ck for oeel off oroamag0,
24. Remove the circlip and pinion shaft sleeve from the
oinion shaft.
(cont'd)
17-51

Steering Gearbox
Disassembly (cont'dl
25. Using a cutter or an equivalent tool, cut and remove
the four seal rings from the sl6eve.
CAUTION: Bc clroful not to drmrg. ths .dgc. otthc alcava g1oov6 whan rcmoving the 3cd rings
lnd O.ring.
Using a cutter or an gquivalent tool, cut the valve
seal ring and O-ring Et the groove the pinion shaft.Remove the valv€ saal ring 8nd O-ring,
CAUTION: Br crrltul not to drm.gr thc cdgct ofthc plnion rhdt grooya whcn rcmoving the vllvc
!.!l ring rnd O-ring.
26.
SI-EEVE
Cutting slot position.
17.52
Remova the valve oil seal 8nd backup ring from thepinion shaft.
NOTE:
. Inspect the ball bearing by rotating the outer
race slowly. lf thsre is excessive play, replace thepinion shaft and sleeve as an assembly.. The pinion shaft and sleeve are a precise fiu donot intermix old and new pinion shafts and
steev8s,
28, Press th6 valve oil s€al and roller besring out ofthe
valve housing using a hydraulic press and specialtool shown below.
PILOT COLLARO?GAF - PHTO1OO

Reassembly
NOTE:
. Clean the disassembled parts with a solvent and dry them with compressed air. Do not dip the rubber parts in a sol-
vent.
. Always replace the O-rings and rubber seals with new ones before assembly.
. Apply power steering fluid or steering grease {HONDA P/N: 08733 - 8070E) to the parts indicated in the assembly pro-
cedures.
. Do not allow dust, dirt. or other foreign materials to enter the power steering system.
. Use the appropriate specialtools where necessary.
FLANGC BOLT20 N.m 12.0 kg{.m, lil lbt'ftl
CYLINDER PIPE A26 N'm (2.7 kgf.m, 20 lbf.ftl
VALVE I{OUSING
BOLI..ER BEARINGReplace.
VALVE SEAL RINGReplace.+-cncl|P
RACK GUIDE SCREW
S1IEVE SEAI RINGSReolace.
SITEVE
BACKUP RIM}
VALVE SEAL RINGRaplacs.
O.RINGReplac€.LOCKNUT
CYLINDER HOUSING
O-RINGBACKUP RING Replace.
\
PINION SHAFT
SHIMS
O-RINGReplace.
CYUNDER END SEALReolace.GEAR HOUSING
CYLINDER END SEALReplaco.O.RINGReplace.
I
x nd#$Y
IPISTON SEAL RINGReplace.
STEERING RACK
(cont'd)
17-53

Steering Gearbox
Reassembly (cont'd)
SI,-EEVE SEAL RINGSBe sure that thesear ings are notturned up, theninstall.
Press the new roller bearing into the valve housing
using a hydraulic press and special tool as shown.
NOTE: Place ths roller bearing on the valve hous-
ing with its letter stamped facing up towards the
valve side.
Pr.33,
I
PINION
E
20.
ATTACHMENT,32x35mm077/aO - (x)1010O
ROLLER BEARINGLetter stamped face
21.Apply vinyl tape to the pinion shaft, then coat thevinyl tape with power steering fluid.
Insert the pinion shaft into the valve housing.
CAUTION: Be carotul not to damage tho valvs soalrings.
23. Remove the vinyltape from the pinion shaft.
Soaling lip frc..
VALVE OIL SEAL
VALVC HOUSING
17-56
24. Press the pinion shaft/sleeve using a hydraulic
Dress as shown.
CAUTION: Before irserting the pinion 3haft, bosuro that the backup ring is csntored with the pin.
ion shaft bearing,
BACKUP BING

Steering Gearbox
Reassembly lcont'd)
-4. Determine the requifed thickness of the 32 mm
shims by subtracting the clearance obtained in thestep -3 from the total thickness of the four shims.(Total thickness of the 4 shims) - (Clearance) =
Required thickness of the shims
NOTE: Select the shims so that th6 total thicknessis close to, but less than the required thickness.
Exampls:
Measu.ement is 0.28 mm (0.011 in):
0.70 - 0.28 = 0.42 mm (0.028 - 0.011 = 0.0't7 in)
The selected shims should be 0.25 mm (O.O1O in) and0.15 mm (0.005 in) in thickness.
lf the required shim thickness is 0.lO mm or less, no
shims are necessary.
i[9. Set the selected 32 mm shims on the bearing sur-face of the g€arbox housing.
50, Coat the new O-ring with gresse and install it in thegroove in the gearbox housing.
Apply grease to the needle bearing in the gearbox
housing.
Install the valve body unit on the gearbox housing
by engaging the gears.
NOTE: Note the valve body unit installation posi-
tion (direction of pipe connection).
Tighten the flange bolts to the specified torque.
FLANGE BOLT20 N.m (2.0 kgt m, 14lbf.ft)
VALVE BODY UNIT
ct.
O-RING
-ffiti
NEEOLE BEARING
_#{
17-60
BACK GUIDE SCREW
54. Installthe cylind6r pipes A and B.
NOTE:
. Clean the joints ofthe cylinder pipe A and B tho.-oughly. The joints must be free of foreign mat€.i-
at,
o Install the cylinder pipe A and B by tighting theflare nuts by hand first, then tighten the flarenuts to the specified torque starting with thecylinder side nuts.
CYLINDER PIPE B
Grease the sliding surface of the rack guide andinstall it onto the gear housing.
Apply a thin coat of grease to the n€w O-ring andinstall it on the rack guide screw.
Install the spring, rack guide screw and locknut onthe gear housing.
Adjust the rack guide screw (see page l7-21).
NOTE: After adjusting, check that the rack movessmoothly by sliding to rack right and left.
LOCKNUT
-6t
26 N.m (2.7 kg{.m,20lbtft)