1994 HONDA INTEGRA coolant capacity

Standards and Service Limits
Engine Lubrication - Section g
Cooling - Section t0
ng the coolant in the reservoir and that remaining in the engine.
eclton u _
MEASUREMENTSTANDARD INEW}SERVICE LIMTT
g talter
tiher
g filter
Engine oilCapacity etaet engine
f (US qt, lmp qt)
818C1 engine
Inner-to-outer rotor clearance
Pump horising-to-outer rotor clearance
Pump housing-to,rotor axial clearance
rressure setting at engine oil temp. 176.F {gO.Ct
kPa lkgtcm,, psi) At idte
At 3,000 rpm
4.6 {4.9, 4.0}tor engine overhaul
3.8 (4.0, 3.3) for oil change, inctudin
3.513.7, 3.11 for oil change, without
4.8 {5.1, 4.2) for engine overhaul
4.0 (4.2, 3.5) lor oit change, includin
3.7 i3.9 3 3l fdr ^il .hi
Oil pump
0.04 - 0.16 (0.002 - 0.006)
0.10 - 0.19 (0.004 _ 0.007)
0.02 - 0.07 (0.001 , 0.003)
0.20 (0.008)
0.21 (0.008)
0.1s (0.006)
Relief valve
70 (0.7, 10) min.
3{0 {3.5,50) min.
MEASUBEMENTSTANDARD INEWI
RadialorCoolant capacity I {US qt, lmp
I Including engine, heater, I
I cooling line and reservoir I
Reservoir capacity:
0.61 (0.63 US qt,0.53 tmp qt)
q0 81881 engine
818C1 engine
Opening pressure kPa (kgf/cm?, psi)
start to open oF (.C)
Fully open .F (.C)
Valve lift at fully open
lhermoswitch "ON" temperature .F {oC)
Thermoswitch "OFF" temporature "F (.C)
M/T: 6.4 (6.8, 5.6)tor overhaul
4.4 (4.6.3.9) f6r s66lsn1gh66q.*
A,rf: 6.7 {7.1, 5.9) for overhaul
4.7 {5.0, 4.1) for coolant chanoe*
M/T: 6.7 {7.1, 5.9} for overhaul
4.7 {5.0, 4.1) for coolant chanoe*
,3 - 113 toss - trs, r3= Jt&
-
196 - 203 (91 - 95)
Subtract 5 - 14 (3 - 8) from actuat -ON',
169 - 176
194 (90,
8.0 (0.31)
{76 80}
temperature
Radiator cap
Thermostst
Cooling fan
3-6

lllustrated Index
@ sy"t". is under high plessure when engine
is hot. To avoid dsnger of relsssing scalding engine
coolant. remove cap only when engine is cool.
Total Cooling System Capacity (lncluding heater and
r€servoirl
Bl8Bl engine:
Mfl: 6.4 | {6.8 US qt, 5.6 lmp qt}
AlTt 6.7 | {7.1 US qt, 5.9 lmp qt}
Bl8Cl engine:
Mfi: 6.7 t {7.1 US qt, 5.9 lmp qt}
CAUTION: lf any engine coolant spills on paint€d por-
tions ot the body, rinse it ofl immediately.
NOTE:
a Check all cooling system hoses for damage. leaks or
deterioration and replace if necessary.
a Check all hose clamps and retighten if necessary.
a Use new O-rings when reassembling.
CONDENSERFAN SHROUD{soe soction 221
6 x 1.O mm7 N.m (O.7 kgt.m. 5 lbf.ftl
ATF COOLERHOSES{81881 6ngine)
RADIATOREngine coolant refilling and bleeding,page 10-5Leak test, page 'l0-6
Inspect soldered joints andseams for leaks.Elow out dirt from betweencore fins with compressed air.lf insects, etc., are clogging.adiator, wash them off withlow pressure water,
S!
P
R
U
COOLANTRESERVOIR
5x0.8mm4.4 N.m (O.45 kgf.m,3.3 lbl.fr)
M/T: Manual t.anamiaaionA/T: Automatic t.ansmiasionATF: Automatic t.ansmission fluid
\*
*)
FAN SHROUD
10-2

@ ne-oving the radiator cap while the engine
is hot can cause the engine coolant to splay out, seri-
ously scalding you. Always let the engine and radiatol
cool down betore removing the radiator cap.
CAUTION: When poudng engine coolant, be sure to shut
the relay box lid and not to let coolant spill on the elec-
tlical pans or the paint. ll any coolant spills, rinse it otf
immediately.
1. Slide the heater temperature control lever to maxi-
mum heat.
Make sure the engine and radiator are cool to the
touch.
2. Remove the radiator cao.
3. Loosen the drain plug on the bottom of the radiator,
and remove the drain bolt from the enoine block. Let
the coolant drain out.
ENGINE DRAIN BOLT78 N.m {8,O kgt.m, 58 lbt.ftlApply liquid gasker tobolt thread when installing.WASHERReplace.
5.
Remove the reservoir from its holder by pulling it
straight up. Drain the coolant, then put the reservoir
back in its holder.
When the coolant stops draining, apply liquid gasket
to the drain bolt threads, then reinstallthe bolt with
a new washer. Tighten it securely
6. Tighten the radiator drain plug securely.
7. Mix the recommended antifreeze/coolant with an
equal amount of water in a clean container.
NOTE:
. Use only HONDA-RECOMMENOED antifreeze/
coolant.
a For best corrosion protection, the engine coolant
concentrations must be maintained year-round at
50% MINIMUM. Coolant concentrations less than
50% may not provide sufficient protection
against corrosion or freezing.
CAUTION:
a Do not mix ditterent blands ot anti-freeze/
coolants.
a Do not use additional rust inhibitois or anti-rust
products; they may not bs compatibl€ with the
recommgndsd engins coolant.
Engin€ Coolant Retill Capacity: including reservoir
{0.6 t (0.6 US qt, 0.5 lmp qt)).
81881 engine:
MlTt 4.4 | (4.6 US qt, 3.9 lmp qr)
Afft 4.7 [ (5.O US qt,4.1 lmp qt]
Bl8Cl engine:
Mnt 4.7 | (5.0 US qt.4.1 lmp qt)
8. Pour coolant into the radiator up to the base of the
filler neck.
9. Loosen the bleed bolt on top of the engine. Tighten
it again when coolant comes out in a steady stream
with no bubbles.
BLEED BOLT
1O. Refill the radiator to the base of the tiller neck. Put
the cap on the radiator. and tighten it only to the tirst
stop, Stan the engine and let it run until it warms
up (the radiator cooling fan comes on at leasttwice).
11. Turn oft the engine. Check the level in the radiator,
and add coolant it needed. Install the radiator caD,
and tighten it fully.
'1 2. Fill thereservoirto the MAX mark. lnstallthe reser-
voir cap.
9.8 N.m (1.O kgl.m, 7.2 lbf.ftl
Engine Coolant Refilling and Bleeding
10-5