1993 DODGE TRUCK check engine light

GASOLINE ENGINE MAINTENANCE SCHEDULE

LIGHT
DUTY
CYCLE

SCHEDULED
MAINTENANCE
FOR
EMISSIONS
CONTROL
-
PROPER
VEHICLE
PERFORMANCE

Inspection and service is also necessary any
rime
a
malfunction
is observed or suspected.

X
= Scheduled maintenance for all vehicles.

O
= Scheduled maintenance for all vehicles, Recommended for proper
vehicle
performance.
Where both
time
and mileage Miles (Thousand) are
shown,
follow the
interval

which
occurs
first. Kilometers (Thousand) 7'A
15
22'A
30
37'A
45
52'A

60
67'A
75
82'A

90 97'/2 105 112'A
120
Where both
time
and mileage Miles (Thousand)
are
shown,
follow the
interval

which
occurs
first. Kilometers (Thousand) 12 24
36 48
60 72 84 96 108 120
132 144 156 168 180 192

Coolant
Condition,
Coolant
Hoses/Clomps
X X X X X X

O O O O O
O O O
o
O

Exhaust
System—Check
X
X X X X

X
O O O

o
O
O O
o o o

Oil—Change
(6 months)
X X X X X X

O O O

o o

O O
o o
o
Oil Filter—Change (2nd Oil Change)
X
X X
o o
O
o
o

Spark
Plug—Replace
X

0
o o

Air
Filter—Replace
X

o

O
o

Coolant—Flush/Replace
(36 months) &
24
months/48 000 km
(30,000
miles)
thereafter
O

X
X

PCV
Valve—Replace if
Necessary
O'
O' O'

Battery—Replace
O

This maintenance is recommended by Chrysler Corporation to the owner, but is not
required
to
maintain
the
warranty.

0 - 6
LUBRICATION
AND
MAINTENANCE
GASOLINE ENGINE MAINTENANCE SCHEDULE

HEAVY
DUTY
CYCLE

Inspection and service is also necessary anytime
a
malfunction is observed or suspected.
When both
time
and mileage
are
Miles (Thousand)

shewn,
follow
the
interval

which occurs first. Kilometers (Thousand) 6
12 18 24
30 36 42 48 54
60 66 72

78
82V2
84 90
96
102 108
When both
time
and mileage
are
Miles (Thousand)

shewn,
follow
the
interval

which occurs first. Kilometers (Thousand) 9.6 19 29
38 48 58 67 77
85 96 106 116
125 132
135
145
154 164
174

Coolant
Condition, Coolant
Hoses/Clamps
X
X X X
X X X X
X X X X
X X X
X X X

Exhaust
System
—
Check
X X X X X X X X X X X
X X X X X
X X

Oil
—
Change
(6
Months)
X X X X X X X
X X

X
X
X

X X X

X X
X

Oil
Filter
—
Change (2nd
Oil
Change)
X X X X
X X
X X
X

Drive Belt Tension
—
Inspect
&
Adjust
X' X
X1

X X' X

Drive Belts (V-Type)
—
Replace
X

Air
Filter/Air
Pump
Air
Filter
—
Replace
X X X
X

Crankcase
Inlet
Air
Filter
(6 &
8
Cyl.
Eng.
Only)
—
Clean
X X
X X

Spark
Plug
—
Replace
X X X

Fuel
Filter
—
Replace as necessary

Coolant
—
Flush/Replace
(36
months)
& 24
months/48
000 km

(30,000
miles)
thereafter
X
EGR
Valve
&
Tube
—
Replace X2

EGR
Tube
—
Clean Passengers
X2
PCV
Valve
—
Replace X2

Vacuum
Emission
Components
—
Replace
X

Ignition Timing
—
Adjust
to
Specs,
as necessary X
Ignition Cables, Distributor Cap
&
Rotor
—
Replace
X

Manifold Heat Control Valve
—
Lubricate
X

Battery
—
Replace X

Oxygen
Sensor
—
Replace
X2

1 For California vehicles, this maintenance is recommended
by
Chrysler Motors
to the
owner but, is not
required
to
maintain the
warranty
on the
air
pump drive
belt.

2 Requires
Emission
Maintenance Reminder Light.
If
so equipped, these parts
are to be
replaced
at the
indicated mileage,
or
when the
emissions
maintenance reminded light remains on continuously
with
the key in the
"on" position, whichever occurs first.
J9100-20

DIESEL
ENGINE
MAINTENANCE
SCHEDULE
HEAVY
DUTY
CYCLE
Inspection
and
service
is
also
necessary
any
time
a
malfunction
is
observed
or
suspected.

Iff both
time
and distance Miles (Thousand)
are listed, use the
interval

that
ends
first. Kilometers (Thousand) 6
12
18 24
30 36 42

4S
54
60 66
72 78
84 90 96
102 108
Iff both
time
and distance Miles (Thousand)
are listed, use the
interval

that
ends
first. Kilometers (Thousand) 9,6 19
29
38 48 58 67

77

85 96 106
116 125 135 145 154
164 174

Coolant
Condition, Coolant
Hoses/Clamps
(12 months)

Coolant
Flush/Replace (36 months) & 24 months/
48 000 km
(30,000
miles)
thereafter
O

Oil—Change
(6 months)
X X X
X X X
X X X X X
X X X X X X
X

Oil Filter—Replace (Every Oil Change)
X X X
X X X
X X
X X X
X
X X X X
X X

Drive Belts—Replace
As
Necessary
X X
X X X X

Air Filter—Replace
X X
X X

Air Filter—Clean (California Only) e

®

• •
Air
Filter
Canister—Clean
o o o
o

Fuel Filter—Service When Necessary

Injection
Pump
Timing & Engine Idle Speed—

Check
& Adjust
©

• 9 • • •
Underhood Rubber/Plastic Components—Inspect/Replace • • • • •

X
— All vehicles
O
— All
vehicles
except
California.
Recommended
for
California.
•
— California only.
Recommended
for all vehicles.

•

LUBRICATION
AND
MAINTENANCE
0 - 15
DIESEL
ENGINES

The Diesel engine oil level indicator is located at
the left center of the engine, above the
fuel
injection

pump (Fig. 3).

Fig.
3
Diesel
Engine
Oil
Dipstick

ACCEPTABLE
OIL
LEVEL
To maintain proper lubrication of an engine, the
engine oil must be maintained at an acceptable level.
For gasoline engines, the acceptable levels are indi­ cated between the ADD and
FULL
marks on oil
dip­
stick. For Diesel engines, the acceptable levels are
indicated between the L (low) and H
(high) marks
on
oil dipstick. The oil level should be checked periodically. The
vehicle should be on a level surface. Wait for
five
minutes after stopping the engine. For gasoline en­
gines,
add oil only when the level indicated on the
dipstick is at or below the ADD mark. For Diesel en­
gines,
add oil only when the level indicated on the
dipstick is between the L and H marks.
Never oper­
ate a Diesel
engine when
the oil
level
is below
the L mark. The distance between the L and H
marks represents 1.9L (2 Qts) engine oil.

CAUTION:
Do not
overfill
an
engine crankcase
with

oil. This
will
cause
oil
aeration
and
result
in a de­

crease
in the
engine
oil
pressure.
ENGINE
OIL
CHANGE AND FILTER REPLACEMENT

WARNING: PROTECTIVE CLOTHING
AND
GLOVES SHOULD
BE
WORN. EXPOSED SKIN SHOULD
BE

WASHED
WITH
SOAP
AND
WATER
TO
REMOVE
USED
ENGINE
OIL.
DO NOT
USE
GASOLINE, THIN­
NER,
OR
SOLVENTS
TO
REMOVE ENGINE
OIL

FROM
SKIN.
DO NOT
POLLUTE. DISPOSE
OF
USED
ENGINE
OIL
PROPERLY.
ENGINE
OIL
FILTER

All engines are equipped with a throw-away type
oil filter. The same type of filter is recommended
when the filter is changed.

OIL CHANGE
AND
FILTER
REPLACEMENT
Bring engine up to normal operating temperature.
A more complete drainage of oil will result.
(1) Remove the drain hole plug and drain the en­
gine oil from the crankcase.
(2) Install the drain hole plug with a replacement
gasket. For gasoline engines, the oil filter should be
replaced during every second engine oil change.
For Diesel engines, the oil filter should be re­
placed during every engine oil change.
(3) Rotate the oil filter counterclockwise to remove
it.
(4) Clean the engine cylinder block oil filter boss. (5) Apply a light coat of new engine oil to the rub­
ber seal on the oil filter.
(6) Install and hand tighten the oil filter 1/2 to 3/4
of a turn clockwise. (7) Add new engine oil at the fill hole location on
top of the engine cylinder head cover. Wipe off any spilled oil.
(8) Observe the oil level on the dipstick.

CAUTION:
Do not
overfill
the
engine crankcase
with

oil.
(9)
Start the engine. Observe the oil pressure
gauge or warning lamp (as applicable). If the oil
pressure does not increase, stop the engine immedi­ ately. Check oil level.

COOLING SYSTEM

WARNING:
USE
EXTREME CAUTION WHEN
THE
ENGINE
IS
OPERATING.
DO NOT PUT
YOUR
HANDS NEAR
THE
DRIVE BELT(S), PULLEYS
OR
FAN BLADE.
DO NOT
STAND
IN A
DIRECT LINE
WITH
THE FAN
BLADE.

INSPECTION SCHEDULE
Determine the coolant level. Inspect the cooling
system hoses/clamps after each service interval has
elapsed.

COOLANT LEVEL
It is recommended that the engine coolant level be
inspected at least once a month during periods of hot
weather.
With the engine at normal operating temperature,
check the coolant level in the coolant reserve tank.
The coolant level must be at least above the ADD mark. Add coolant to the coolant reserve tank only.

•

LUBRICATION
AND
MAINTENANCE
0 - 23 GEAR SHIFTER BOOTS
Inspect the shifter boots periodically for stone and
heat damage. Replace, if necessary.
SEVERE DRIVING CONDITIONS The interval between the transmission drain and
refill maintenance should be decreased to:
• NV4500 manual transmission—every 29 000 km (18,000 miles)
• Automatic transmission—every 19 000 km (12,000
miles)
A severe driving condition includes:
• Extended operation with heavy cargo loads
• Driving in deep mud or snow
• Off-road operation (4WD)
• Trailer towing
• Operation as a commercial vehicle
• Snow plowing
MANUAL TRANSMISSIONS

INSPECTION/LUBE
OIL
LEVEL
The transmission should be checked for leaks when
other service is necessary under the vehicle. To check
the lube oil level, remove the fill hole plug (Fig. 2 ). If the level is below the bottom of the fill hole, raise
the level to the bottom of the fill hole with:
• Castrol Syntorq for NV4500 transmissions
• SAE 5W-30 engine oil (API Service SG, SG/CD or
SG/CE) for Getrag 360 transmissions.

Fig.
2 NV4500 Manual
Transmission

DRAIN
AND
FILL
The NV4500 transmission fluid should be changed
according to the intervals listed in the Manual
Transmission—Drain & Refill Intervals chart below.

Also,
refer to the Fluid Capacities chart.
AUTOMATIC TRANSMISSIONS

FLUID
LEWEL
It is recommended that the fluid (ATF) level in au­
tomatic transmissions be checked while involved
with other underhood maintenance.
Vehicle operation with an incorrect ATF level
will greatly reduce the life of the transmission.
Fig.
3 Getrag 360 Manual
Transmission

MANUAL TRANSMISSION-DRAIN & REFILL INTERVALS
Normal

Service
Light
Duty
Cycle

60 000
km
37,500
miles

Heavy
Duty
Cycle

58 000
km
36,000
miles

Severe
Service
29 000
km
18,000
miles

J9000-43

The condition of the ATF also should be deter­
mined. If the ATF is dark in color and has a strong odor, the fluid should be changed. Also the filter should be replaced and the bands adjusted.
The following procedure must be used to check the
automatic transmission fluid (ATF) level.
(1) Position the vehicle on level ground.
(2) Operate the engine at idle speed.
(3) Apply the parking brake.
(4) Place the gear selector in N (neutral).
(5) Remove the dipstick from the tube. Wipe it
clean and determine if the ATF is hot or warm.
Hot ATF has a temperature of approximately
82°C (180°F). Warm ATF is when its temperature
is between 29-52°C (85-125°F). (6) Wipe the dipstick clean and completely insert it
into the tube. Remove the dipstick from the tube and
observe the ATF level.
(7) If the ATF is hot, the level should be in the
crosshatched area that is marked OK.
(8) If the ATF is warm, the level should be be­
tween the two dimples.

0
- 24
LUBRICATION
AND
MAINTENANCE

•
CAUTION:
Do not
overfill
the
transmission.
(9) Adjust
the
level
of the ATF
accordingly.
It
is
important
to use the
correct fluid
in an

automatic transmission. MOPAR®ATF PLUS
(ATF Type
7176)
should
be
used. Dexron®
II

ATF
can be
used
if the
recommended fluid
is not
available,
(10) Insert
the
dipstick into
the
tube.

DRAIN, FILTER CHANGE, BAND ADJUSTMENT AND REFILL
The chart below lists
the
intervals
at
which
the

transmission should
be
serviced. Also, refer
to the

Fluid Capacities chart
for
fill capacity.
AUTOMATIC TRANSMISSION SERVICE
IN-
TERVALS

Normal

Usage
Light
Duty
Cycle

60 000
km
37,500
miles

Heavy
Duty
Cycle

38
000 km 24,000
miles

Severe
Usage
19 000 km 12,000
miles

J9100-19

It
is
very important
to use the
correct fluid
in

an automatic transmission. MOPAR®ATF PLUS
(ATF Type
7176)
should
be
used.
An
equivalent
Dexron®
II ATF
could
be
used only
if the
recom­
mended fluid
is not
available.
The torque converter does
not
have
a
drain plug.
No attempt should
be
made
to
drain
the
converter.
Refer
to
Group
21
—Transmissions
for
transmission
drain
and
refill procedures.

TRANSFER
CASE
(4WD
VEHICLES)
INSPECTION The NP205
and
NP241 transfer cases fluid level
should
be
checked whenever maintenance
is
neces­
sary under
the
vehicle.

FLUID
LEVEL
The vehicle must
be
level when
the
fluid level
is checked.
The transfer case drain fill hole plugs
are
located
at
the
rear
of the
housing (Figs.
4 and 5).

Determine
the
transfer case fluid level according
to

the following procedure.
(1) Raise
and
support
the
vehicle.
(2) Remove
the
fill hole plug (Figs.
4 and 5)
from
the transfer case.
The
fluid level should
be at the

bottom edge
of the
fill hole.
The
level
can be
slightly
below
the
bottom edge
of the
fill hole
if the
fluid
is
cold.
(3)
If the
level
is not
acceptable, raise
the
fluid
level
to the
bottom edge
of the
fill hole with: • MOPAR®ATF PLUS
or an
equivalent Dexron
II®

ATF
for
NP241 transfer case
• Multi-purpose gear
oil (API GL-5) or
engine
oil

(API
SG,
SG/CD
OR
SG/CE)
for
NP205 transfer

cases.

Add fluid
in
small amounts
to
raise
the
level. (4) Install
the
fill hole plug (Figs.
4 and 5).

Tighten
the
fill hole plug
to 27 N-m (20
ft-lbs) torque.
(5) Remove
the
support
and
lower
the
vehicle.

Fig.
4
HP241 Transfer
Case
Fig.
5
NP205 Transfer
Case

FLUID DRAIN
AND
REFILL The transfer case fluid should
be
changed every
60

000
km
(37,500 miles).
For
vehicles subject
to the

HEAVY DUTY CYCLE Maintenance Schedule,
a 58

000
km
(36,000 miles) interval
is
recommended.
(1) Raise
and
support
the
vehicle.
(2) Remove
the
fill hole plug (Figs.
4 and 5)
from
the transfer case. (3) Place
an
appropriate container under
the
trans­
fer case drain hole plug (Figs.
4 and 5).
(4) Remove
the
drain hole plug. Drain
the
fluid
from
the
transfer case into
the
container.

•

LUBRICATION
AND
MAINTENANCE
0 - 25
CAUTION:
Do not
over-tighten
the
drain
and fill
hole

plugs.
Over-tightening
can strip the
hole
threads

and/or crack
the
aluminum housing.

(5) Install the drain hole plug (Figs. 4 and 5) in
the transfer case. Tighten the drain hole plug to 27 N*m (20 ft-lbs) torque. (6) Fill the transfer case to the bottom edge of the
fill hole (Figs. 4 and 5) with: • MOPAR®ATF PLUS or an equivalent Dexron II®
ATF for NP241 transfer cases
• Multi-purpose gear oil (API GL-5) or engine oil (API SG, SG/CD or SG/CE) for NP205 transfer cases. (7) Install the fill hole plug (Figs. 4 and 5) in the
transfer case. Tighten the plug to 27 N«m (20 ft-lbs) torque.
(8) Remove the support and lower the vehicle.
FLUID SPECIFICATION
• MOPAR®ATF PLUS or an equivalent Dexron II®
ATF for NP241 transfer cases • Multi-purpose gear oil (API GL-5) or engine oil (API SG, SG/CD or SG/CE) for NP205 transfer cases
NP20I
MULTI-PURPOSE GEAR OIL/ENGINE
OIL
SELECTION

MULTI-PURPOSE GEAR OIL-if the anticipated
minimum temperature will: • Be above 32°C (90°F)-use SAE 140, API GL-5;
• Decrease to as low as -23°C (-10°F)-use SAE 90,
API GL-5; and • Be below -23°C (-10°F)-use SAE 80, API GL-5. ENGINE OIL—if the anticipated minimum tem­
perature will be: ® Above 0°C (32°F)-use SAE 50, API SG, SG/CD or
SG/CE;
• Below 0°C (32°F)-use SAE 30, API SG, SG/CD or SG/CE.
SHIFT MECHANISM-NP241 AND NP205 The transfer case shift mechanism should be
cleaned and lubricated as necessary.
Lubricate the pivot, the sliding contact areas and
the shift linkage pivot ends with light-weight engine oil (Figs. 6 and 7).

AXLES
INSPECTION/LUBRICANT LEVEL For normal vehicle operation, periodic axle lubri­
cant level checks are not necessary. The exterior of
the axle housing should be inspected for leakage. Check the lubricant level to confirm the leakage.

LUBRICANT LEVEL
(1) Raise the vehicle with an axle or wheel type
hoist. Support the vehicle.
(2) The rear axle differential housings have a rub­
ber, PRESS-IN type fill plug (Fig. 8). Pry the fill
TRANSMISSION

ASSEMBLY
GEARSHIFT
MECHANISM TRANSFER CASE

SCREWS
(2)
50
FT. LBS.
(68 N*m)
CLAMP
SHIFT
ROD

SCREW

80 IN.
LBS.

(9 N*m)
RP1091
Fig.
6 Shift
Mechanism
Lubrication—NP241 Transfer
Case

Fig.
RY682
7 Shift
Mechanism
Lubrication—NP205 Transfer

Case

plug from the differential housing. The front axle (4WD vehicles)*differential housings have a thread­
ed-type fill plug (Fig. 9). Un-thread the fill plug from
the differential housing.
(3) The lubricant level should be within 12 mm
(1/2 in) of the fill hole for the 8.25 and 9.25 rear ax­

les.
The lubricant level should be between 12mm (1/2
in) and 24mm (1 in.) of the fill hole for the Dana ax­

les.

(4) If necessary, add lubricant to raise the level to
the acceptable position.
(5) Install the fill hole plug in the differential
housing (Figs. 8 and 9).

DRAIN
AND
REFILL
Periodic axle lubricant change for normal vehicle
operation is not necessary. Refer to the chart below-

0
- 28
LUBRICATION
AND
MAINTENANCE

•
CHASSIS AND BODY

page

Body
Component Mechanisms
32
Front
Suspension
Ball
Joints
28

Front
Wheel Bearings
29

Headlamps
32

Lower
and
Upper Suspension
Arm
Bushings
.... 30

Manual
Steering Gear
28

STEERING
LINKAGE

INSPECTION When
a
vehicle
is
raised
for
maintenance under
the vehicle,
all
steering components should
be
checked.
LUBRICATION SCHEDULE The steering linkage
is
lubricated with
a
chassis
lubricant. However,
it is
recommended that
the
link­
age
be
inspected
and
lubricated after each:
•
24 000 km
(15,000 miles) interval
or
every
6

months,
for 2WD
vehicles subject
to the
LIGHT
DUTY CYCLE Maintenance Schedule
•
9 600 km
(6,000 miles) interval
or
every
6
months,
for
2WD
vehicles subject
to the
HEAVY DUTY
CY­
CLE Maintenance Schedule
•
12 000 km
(7,500 miles) interval
or
every
6

months,
for 4WD
vehicles subject
to the
LIGHT DUTY CYCLE Maintenance Schedule
•
9 600 km
(6,000 miles) interval
or
every
6
months,
for
4WD
vehicles subject
to the
HEAVY DUTY
CY­
CLE Maintenance Schedule.
LUBRICATION (1) Inspect
the
steering linkage
for
looseness
and

excessive wear. (2) Replace,
all
ruptured seals
and
damaged steer­
ing linkage components. Damaged seals should
be re­

placed
to
prevent leakage
and
contamination
of the
lubricant.

CAUTION:
Use
care
to
prevent lubricant from
con­

tacting
the
brake rotors.

(3) Lubricate
the
steering linkage:
• Clean
the
Zerk type lubrication fittings
on the tie-

rod
and
center link ball-stud ends
• Lubricate
the
ball studs with MOPAR®Multi-Mile- age Lubricant
• Wipe
the
excess lubricant from
the
exterior sur­
faces
of the
ball joints
page

Power
Brake System
30
Power
Steering System
. . 29

Rear
Wheel Bearings
30

Speedometer Cable
33

Steering Linkage
28

Tires
32

FRONT
SUSPENSION
BALL JOINTS

INSPECTION When
a
vehicle
is
raised
for
lubrication/general
maintenance,
the
ball joints should
be
inspected.
LUBRICATION SCHEDULE The front suspension ball joints
are
lubricated dur­
ing manufacture with
a
long-life chassis lubricant.
However,
it is
recommended that
the
ball joints
be

inspected
and the
studs lubricated:
•
At
each
36 000 km
(22,500 miles) interval
or
every
2 years,
for
vehicles subject
to the
LIGHT DUTY
CY­
CLE Maintenance Schedule
•
At
each
9 600 km
(6,000 miles) interval
or
every
2

years,
for
vehicles subject
to the
HEAVY DUTY
CY­
CLE Maintenance Schedule.
4WD vehicles that
are
frequently driven
off-

road should
be
lubricated
at
every engine
oil
change.
LUBRICATION (1) Inspect
the
front suspension. Examine
the
ball
studs
for
looseness
and
excessive wear. (2) Replace
all
torn ball-stud seals
and
damaged
ball joints. Damaged seals should
be
replaced
to
pre­ vent leakage
and
contamination.

CAUTION:
Use
care
to
prevent lubricant from
con­

tacting
the
brake rotors.

(3) Lubricate
the
ball studs:
• Clean
the
Zerk type lubrication fittings
on the

ball-stud ends
• Lubricate
the
ball studs with MOPAR®Multi-Mile-age Lubricant
• Wipe
the
excess lubricant from
the
exterior sur­
faces
of the
ball joints

MANUAL
STEERING
GEAR

LUBRICATION Manual steering gears
are
permanently lubricated
during manufacture. Periodic lubrication
is not
nec­
essary.

•

LUBRICATION
AND
MAINTENANCE
0 - 29
POWER STEERING SYSTEM

SERVICE SCHEDULE

FLUID
LEWEL

WARNING.
THE
POWER
STEERING
FLUID LEVEL
SHOULD
ALWAYS
BE
CHECKED
WITH THE EN­

GINE
OFF TO
PREVENT
PERSONAL
INJURY.

The power steering fluid should be checked when­
ever the engine is being serviced for other reasons. Clean the outside of the cap before removing. The
fluid should be at the proper level indicated on cap dipstick (Fig. 1).

Fig.
1
Power
Steering Reservoir & Cap—Typical
The reservoir fluid level can be determined with
the fluid either hot or cold. If the fluid level is below
the FULL HOT or FULL COLD marks on the dip­ stick, add power steering fluid. The dipstick is at­
tached to the reservoir cap (Fig. 1).
FLUID SPECIFICATION MOPAR03)Power Steering Fluid is highly recom­
mended.

FRONT
WHEEL BEARINGS
INSPECTION/LUBRICATION SCHEDULE

2WD
VEHICLES
It is recommended that 2WD front wheel bearings
be inspected for proper lubrication whenever the
brake rotors are removed or at least: • At each 39 000 km (24,000 miles) interval for ve­
hicles subject to the LIGHT DUTY CYCLE Mainte­ nance Schedule • At each 36 000 km (22,500 miles) interval for ve­
hicles subject to the HEAVY DUTY CYCLE Mainte­ nance Schedule The bearings should be cleaned and re-packed
with a high temperature, multi-purpose EP lu­
bricant.
4WD
VEHICLES

It is recommended that 4WD front wheel bearings
be inspected for proper lubrication whenever the
brake rotors are removed or at least:
• At each 24 000 km (15,000 miles) interval for ve­
hicles subject to the LIGHT DUTY CYCLE Mainte­ nance Schedule
• At each 19 000 km (12,000 miles) interval for ve­
hicles subject to the HEAVY DUTY CYCLE Mainte­ nance Schedule
For vehicles used for extensive off-road, 4WD
operation, the front wheel bearings should be in­ spected every 1 600 km (1,000 miles).
The bearings should be cleaned and re-packed
with a high temperature, multi-purpose EP lu­
bricant whenever the disc brake rotors are re­ surfaced.
INSPECTION If the lubricant:
• Is not sufficient
• Contaminated with foreign particles
• Appears dry or has been contaminated with water
to produce a milky appearance, the bearings should
be cleaned and re-packed with lubricant.

CAUTION:
Do not add
lubricant
to the
wheel
bear­
ings.
Re-pack completely. Mixing
of
different
types
of lubricants
in
wheel
bearings should
be
avoided.
This could possibly result
in
excessive thinning
and
leakage
of the
lubricant.

LUBRICATION (1) Discard the original seal.
(2) Clean the original lubricant from the bearings
and from the hub cavity (Figs. 2 and 3).
(3) Inspect the bearing rollers for indications of
pitting. Light bearing roller discoloration is consid­ ered normal. A wheel bearing must be replaced if any serious damage exists.
(4) Re-pack the bearings with a high temperature,
multi-purpose NLGI GC-LB lubricant. The use of a
bearing packer is recommended. A small amount of fresh lubricant also should be added to the hub cav­ ity.
BEARING INSTALLA TION/ADJUSTMENT (1) Install the hub/rotor (with inner bearing and
seal) on steering knuckle spindle.
(2) Install the outer bearing, the thrust washer
and the nut.
(3) Tighten wheel bearing nut to 27-34 N^m (240-
300 in. lbs.) torque while rotating hub/rotor. This
will seat the bearings.
(4) Loosen the nut 1/4 of-a-turn (90°), then tighten
it finger-tight.