1993 DODGE TRUCK torque

•

NP20I
TRANSFER CASE
21 - 34i (5) Verify that transfer case range lever is in Neu­

tral.
(6) Move shift lever bracket forward and retighten
bracket bolts (Fig. 3). Shift rod should not bind in shift lever and range lever. Rod should be slip-fit
both levers. (7) Shift transfer case into 4H range. Shift rod
should now be tension-fit in each lever. Shift lever
should be in 4H detent in gate and range lever should be fully into 4H position.
(8) Shift transfer case into 2H and 4L ranges to
verify correct adjustment.

SPEEDOMETER SERVICE
The speedometer driven gear, adapter and vehicle
speed sensor can be serviced with the transfer case in
the vehicle.
SPEEDOMETER COMPONENT REMOVAL/
INSTALLATION (FIG. 4) (1) Shift transfer case into Neutral.
(2) Raise vehicle.
(3) Disconnect wires at vehicle speed sensor.
(4) Loosen and disconnect coupling nut that at­
taches speed sensor to adapter. Then loosen and dis­ connect coupling nut attaching adapter to driven
gear.
(5) Remove vehicle speed sensor and speedometer
adapter. (6) Loosen and remove speedometer driven gear.
(7) Lubricate driven gear with engine or gear oil
and install gear in transfer case. Tighten gear to 11
N*m (100 in. lbs.) torque. (8) Install adapter and speed sensor. Tighten cou­
pling nuts to 17 N»m (150 in. lbs.) torque. (9) Connect wires to speed sensor.
(10) Lower vehicle.

TRANSFER CASE
REMOVAL
(1) Raise vehicle.
(2) Remove drain plug and drain transfer case lu­
bricant. (3) Disconnect vehicle speed sensor wires.
(4) Mark front/rear propeller shafts and yokes for
installation reference. (5) Disconnect and remove propeller shafts. Or dis­
connect shafts at transfer case yokes. Then move shafts aside for working clearance and secure them
to frame rails with wire. (6) Disconnect transfer case shift lever from range
lever on transfer case. (7) Support transfer case with transmission jack.
Secure transfer case to jack with safety chains. (8) Remove nuts attaching transfer case to trans­
mission adapter. (9) Slide transfer case rearward until it is clear of
transmission output shaft.
DISTANCE

SENSOR
ADAPTER
DRIVEN
GEAR
J9021-151

Fig.
4 Speedometer Components.
(10) Lower jack and move transfer case from under
vehicle.
(11) Remove old gasket material from transmission
adapter.

TRANSFER CASE
INSTALLATION
(1) Apply Mopar perfect seal, silicone sealer, or
Permatex No. 2 sealer to both sides of transfer case-
to-transmission gasket. Then position gasket on
transmission. (2) Align and seat transfer case on transmission.
Be sure transfer case input gear splines are aligned
with transmission output shaft. Align splines by ro­
tating transfer case rear output shaft yoke if neces­ sary. Do not install any transfer case attaching
nuts until the transfer case is completely seated against the transmission. (3) Install and tighten transfer case attaching nuts
to 47 N*m (35 ft. lbs.). (4) Install rear crossmember.
(5) Remove jack stand from under transmission.
(6) Align and connect propeller shafts.
(7) Connect vehicle speed sensor wires.
(8) Connect transfer case shift lever to range lever.
Tighten lever locknut to 10 N»m (90 in. lbs.). (9) Fill transfer case with recommended lubricant.
(10) Install transfer case fill plug.
(11) Install skid plate and skid plate crossmember.
(12) Lower vehicle.

TRANSFER CASE DISASSEMBLY
(FIG.
S) REAR RETAINER AND OUTPUT SHAFT
REMOVAL/DISASSEMBL
Y
(1) Loosen rear yoke nut until only 2-3 threads are
holding nut on shaft. (2) Remove bolts attaching rear bearing retainer to

case.

(3) Pull yoke rearward to start rear output shaft
out of clutch. (4) Remove rear yoke nut, washer, seal washer and
yoke.

21 - 350 NP241
TRANSFER CASE

• NP241 TRANSFER CASE

INDEl

page

Checking
Fluid
Level
351

Component Cleaning
and
Inspection
359
Fluid
Drain/Refill
351

General
Information
350

Recommended
Lubricant
.................. 350

Service
Diagnosis
....................... 350

Shift
Linkage
Adjustment
354

Speedometer Adapter/Distance
Sensor
Service
. 352
page

Speedometer Gear, Shaft
Seal,
Bearing
and
Retainer
Service
352

Transfer
Case
Assembly
.................. 361

Transfer
Case
Bearing Replacement
......... 360
Transfer
Case
Disassembly
................ 356

Transfer
Case
Identification ................ 350

Transfer
Case
Installation
................. 356

Transfer
Case
Removal
356

GENERAL
INFORMATION
The NP241 is a part-time transfer case with a low-
range gear system. It has three operating ranges
plus a Neutral position. The low range system pro­ vides a gear reduction ratio for increased low speed
torque capability. NP241 operating ranges are: 2-high, 4-high and 4-low. The NP241 has an aluminum, two-piece gear case.
Drive sprockets and an interconnecting drive chain are used to transmit engine torque to the propeller

shafts.
Four-wheel high and low ranges are undifferenti­
ated. The transfer case is not designed for continuous
operation in 4WD range on hard or paved surfaces.
Four wheel drive ranges are recommended for off
road operation, or on snow covered or similar low
traction surfaces. A front axle disconnect system is used to achieve
two-wheel drive mode. The axle disconnect vacuum motor is actuated by a vacuum switch on the transfer

case.
The switch is operated by the transfer case
range rod. Two-wheel drive range is used for on road, high­
way operation. The four-wheel drive ranges are for off road operation or when the vehicle is driven on
paved road surfaces covered by snow, ice or similar low traction elements.

TRANSFER CASE
IDENTIFICATION
An identification tag (Fig, 1) is attached to the rear
case of each NP241 transfer case. The tag provides
the transfer case model number, assembly number, serial number, and low range ratio. The transfer case serial number also represents the
date of build. For example, a serial number of 9-10-92 would represent September 10, 1992. Transfer case operating ranges are selected with a
floor-mounted shift lever. The shift lever is connected
to the transfer case range lever by an adjustable linkage rod (Fig. 2). A straight line shift pattern is
used. Range positions are marked on the gearshift le­
ver knob.
Fig.
1 NP 241 Transfer
Case

A synchronizer assembly in the transfer case al­
lows the unit to be shifted between 2H and 4H
ranges while the vehicle is in motion. The vehicle should be stopped before shifting into 4L range.

RECOMMENDED
LUBRICANT
Recommended lubricant for the NP241 is Mopar
ATF Plus, type 7176, or Dexron II™ automatic trans­
mission fluid. Use either fluid for topping off the
level, or refilling after service, or normal fluid
changes. Do not use anti-friction additives or similar prod­
ucts in the NP241 transfer case. Use the recom­
mended lubricant only. NP241 transfer case lubricant should be changed
at the intervals specified in the Maintenance Sched­
ule or after service repairs.

SERVICE
DIAGNOSIS
Before attempting to repair a suspected transfer
case malfunction, check all other driveline compo­
nents beforehand. The actual cause of a problem may be related to
such items as: front hubs, axles, propeller shafts,
wheels and tires, transmission, or clutch instead. If all other driveline components are in good condition

•
NP241 TRANSFER CASE
21 - 351
SERVICE
DIAGNOSIS

Condition
Possible
Cause
Correction

TRANSFER
CASE
DIFFICULT
TO
SHIR

OR
WILL
NOT
SHIFT
INTO
DESIRED

RANGE

TRANSFER
CASE
NOISY
IN ALL

DRIVE
MODES

NOISY
IN-OR

JUMPS
OUT
OF
FOUR-WHEEL-DRIVE

LOW
RANGE

LUBRICANT

LEAKING
FROM

OUTPUT
SHAFT
SEALS
OR
FROM

VENT

ABNORMAL

TIRE
WEAR
(a)
Vehicle speed
too
great
to permit

shifting.

(b)
If
vehicle was operated
for
extended
period
in 4H
mode
on dry
paved

surface,
driveline
torque
load
may

cause
difficulty.
(c) Transfer
case
external
shift linkage
binding.

(d) Insufficient
or
incorrect lubricant.
(e) Internal components binding, worn
or
damaged.

(a) Insufficient
or
incorrect lubricant.
(a) Transfer
case
not
completely engaged in
4L
position.
(b) Shift linkage
loose
or
binding.
(c)
Range
fork cracked, inserts worn,
or
fork is binding
on
shift rail.
(d)
Annulus
gear
or
lockplate work
or
damaged.

(a) Transfer
case
overfilled.
(b) Vent
closed
or
restricted.
(c) Output shaft
seals
damaged
or
installed correctly.
(a) Extended operation
on dry
hard
surface
(paved) roads
in 4H
range. (a)
Stop
vehicle and shift into desired

range.
Or
reduce speed
to 3-4
km/h (2-3 mph) before attempting
to
shift.
(b)
Stop
vehicle, shift
transmission
to
neutral, shift transfer
case
to 2H
mode

and
operate vehicle on
2H on dry
paved
surface.
(c) Lubricate, repair
or
replace linkage,
or
tighten loosen components as necessary.
(d) Drain and
refill to
edge
of fill
hole
with
MOPAR
ATF
PLUS
(Type
7176) or
DEXRON
II
Automatic
Transmission
Fluid.

(e)
Disassemble
unit and replace worn
or
damaged
components
as necessary.
(a) Drain and
refill to
edge
of fill
hole
with
MOPAR
ATF
PLUS
(Type
7176) or
DEXRON
II
Automatic
Transmission

Fluid.
Check
for
leaks and repair
if

necessary.
If
unit
is
still
noisy
after

drain
and
refill,
disassembly
and
inspection
may be
required
to
locate

source
of
noise.

(a)
Stop
vehicle, shift transfer
case
to
Neutral, then shift back into
4L
position.
(b) Tighten, lubricate,
or
repair linkage
as
necessary.

(c)
Disassemble
unit and repair
as
necessary

(d)
Disassemble
unit and repair
as
necessary

(a) Drain
to
correct level.
(b) Clear
or
replace vent
if
necessary.

(c) Replace
seals.
Be sure seal
lip
faces interior
of
case
when installed.
Also
be

sure
yoke seal surfaces
are not
scored

or
nicked. Remove
scores
and nicks
with

fine sandpaper
or
replace yoke(s)
if
necessary.

(a) Operate
in 2H on
hard surface (paved)
roads.

and operating properly, refer to the Service Diagno­
sis chart for further information.

CHECKING FLUID LEVEL
Correct fluid level for the NP241 transfer case is to
the bottom edge of the fill plug hole. A correct method of checking fluid level is im­
portant. An accurate check requires that the
transfer case be level. If fluid level is checked with the vehicle parked on
the shop floor, be sure the floor area used is level. If J9021-152
fluid level is checked with the vehicle raised, use ei­
ther a swivel arm or drive-on type hoist to be sure
the vehicle is level.

FLUID DRAIN/REFILL
(1) Raise vehicle.
(2) Position drain pan under transfer case.

(3)
Remove drain and fill plugs and drain lubri­
cant completely. (4) Install drain plug. Tighten plug to 54 N»m (40
ft. lbs.). (5) Remove drain pan.

21 - 352 NP241
TRANSFER
CASE
—
•

Fig.
2
Loosening
Rear Retainer
Fig.
3 Removing/Installing Rear Retainer
(7) Install speedometer driven gear.
(8) Install drain plug. Tighten plug to 54 N-m (40
ft. lbs.). (9) Fill transfer case to edge of fill plug opening
with recommended transmission fluid. (10) Install fill plug. Tighten plug to 54 N-m (40 ft.

lbs.).
(11) Connect propeller shaft. Tighten attaching
bolts to 19 N-m (170 in. lbs.).
(12) Lower vehicle.

SPEEDOMETER
ADAPTER/DISTANCE
SENSOR

SERVICE

ADAPTER/SENSOR
REMOVAL
(1) Raise vehicle.
(2) Remove skid plate and crossmember for access,
if necessary. (3) Remove vehicle speed sensor from pinion gear
adapter (Fig. 4). On models with automatic transmis­
sion, remove sensor adapter as well.
(6) Fill transfer case to bottom edge of fill plug
opening with Mopar ATF Plus, or Dexron II auto­
matic transmission fluid.
(7) Install fill plug. Tighten plug to 54 N«m (40 ft.

lbs.).
(8) Lower vehicle.

SPEEDOMETER
GEAR, SHAFT
SEAL,
BEARING
AND RETAINER SERVICE
The front and rear yokes, output shaft seals, re­
tainers and bearings, and speedometer drive gear can all be serviced with the transfer case in the vehicle.
The following combined procedure outlines removal and installation of these components:

RETAINER
AND
SPEEDOMETER COMPONENT REMOVAL
(1) Raise vehicle.
(2) Remove fill and drain plugs and drain oil from
transfer case. (3) Mark propeller shaft and transfer case yoke for
alignment reference. (4) Disconnect propeller shaft. Secure shaft to un­
derside of vehicle. (5) Remove transfer case yoke retaining nut and
seal washer. Use Special Tool C-3281 to hold yoke
while removing nut. (6) Remove transfer case yoke. (7) Remove retainer seal (if seal or bushing is to be
replaced) using suitable tool.
(8) Install a new seal, if old seal was removed.
(9) Remove speedometer gear from rear retainer.
(10) Mark rear retainer for assembly alignment
reference. (11) Remove retainer attaching bolts and remove
retainer. Pry retainer with screwdrivers to remove it (Fig. 2). (12) Remove rear retainer (Fig. 3). Remove speed­
ometer drive gear, if necessary.
(13) Completely clean off old sealant.
(14) If the retainer or bearing are to be replaced,
remove bearing retainer snap ring from rear retainer
and remove bearing.

RETAINER
AND
SPEEDOMETER COMPONENT INSTALLATION
(1) Install rear output bearing in rear retainer and
install snap ring. (2) Apply a 5 mm (3/16 in.) wide bead of Mopar
Gasket Maker, Loctite 518, or Loctite 573 sealant to
mating surface of rear retainer.
(3) Align retainer case reference marks and install
rear retainer on case. (4) Install and tighten rear retainer attaching
bolts to 24 N«m (18 ft. lbs.). (5) Install output shaft seal (if required).
(6) Install yoke, a new yoke seal washer and yoke
nut. Tighten nut to 149 N-m (110 ft. lbs.) torque.

•

NP241 TRANSFER
CASE
21 - 313
LOCK OIL RING SEAL

ADAPTER

(OVERDRIVE
ONLY)
SPEEDOMETER

PINION
GEAR

ADAPTER
O-RING

SPEEDOMETER
ADAPTER

RETAINER
DISTANCE
SENSOR
J9021-99

Fig.
4 Speedometer
Components

(4) Check vehicle speed sensor mounting area in
pinion adapter. If transmission fluid is found in this area, adapter oil seal is leaking and will have to be
replaced.
(5) Remove bolt and retainer securing pinion gear
adapter to extension housing.

(6)
Carefully work adapter and gear out of hous­
ing. (7) Remove and discard adapter O-ring (Fig. 4).

SPEEDOMETER ADAPTER
OIL
SEAL
REPLACEMENT
Remove adapter oil seal if necessary. Start new
seal in adapter by hand. Then press seal into adapter
with Installer Tool C-4004 until tool bottoms (Fig. 5).
ADAPTER

LOCK
RING

TOOL
(3) Count number of teeth on pinion gear before
installing gear in adapter.
(4) Note range numbers on adapter face (Fig. 6).
These numbers correspond to number of teeth on pin­ ion. (5) Install adapter in housing.

(6)
Rotate adapter until required range numbers
are at six o-clock position (Fig. 6). Be sure adapter
range numbers correspond to number of teeth on pin­ ion. (7) Seat adapter in housing.
(8) Install adapter retainer. Tighten retainer bolt
to 11 N-m (100 in. lbs.) torque.
(9) Install vehicle speed sensor. Tighten sensor
coupling nut to 17 N-m (150 in. lbs.) torque and in­
stall sensor wires.
(10) Check and correct transfer case lubricant level
if necessary.
(11) Install skid plate and crossmember if re­
moved. (12) Lower vehicle.
ADAPTER

O'CLOCK
POSITION

Fig.
6 Indexing Speedometer Adapter
RH75
OIL
SEAL

RH263

Fig.
5
Replacing
Speedometer Adapter
Seal

ADAPTER/SENSOR
INSTALLATION
CAUTION:
Before installing
the
pinion arid adapter

assembly
make sure
the
adapter flange
and its
mounting area
in
transfer case
are
perfectly clean. Dirt
or
sand
will
cause misalignment resulting
in

speedometer pinion gear damage.

(1) Thoroughly clean adapter flange and adapter
mounting surface in extension housing. These sur­
faces must be clean for proper adapter alignment and speedometer operation.
(2) Lubricate adapter oil seal and O-ring with
transmission fluid.

21 - 354 NP241
TRANSFER
CASE

•
SHIFT
LINKAGE
ADJUSTMENT

(1) Remove screws attaching shift lever boot and
seal to floorpan (Fig. 7). Then move boot and seal aside for visual access to shift gate. (2) Move shift lever into 4H position. Be sure lever
is against 4H position in gate. (3) Raise vehicle.
(4) Loosen lock bolt in shift rod adjusting swivel
(Fig. 8). (5) Check shift rod fit in swivel. Be sure rod does
not bind in swivel. (6) Verify that transfer case range lever is in 4H
position (vertical). Move lever if necessary. (7) Tighten shift rod lock bolt to (90 in. lbs.)
torque. (8) Lower vehicle.
(9) Check shift linkage operation.
Fig.
7 Shift
Lever
Boot
And
Seal

•

NP241 TRANSFER
CASE
21 - 361

Fig.
21
Removing
Mainshaft Pilot Bearing
Fig.
22 Installing Mainshaft Pilot Bearing (2) Remove bearing with Tool Handle C-4171 and
Remover C-4610 (Fig. 24).
(3) Clean bearing bore thoroughly.
(4) Install new bearing with Handle C-4171 and
Installer C-4609 (Fig. 25).
(5) Install new seal in rear retainer.

FRONT
OUTPUT
SHAFT
FRONT
BEARING
REPLACEMENT
(1) Remove bearing from front case bore with Tool
Handle C-4171, Remover C-4610 and a shop press (Fig. 26).
(2) Clean bearing bore thoroughly.
(3) Install new bearing with Tool C-4210, Handle
C-4171 and a shop press (Fig. 27).

FRONT
OUTPUT
SHAFT
REAR BEARING
REPLACEMENT
(1) Remove bearing from rear case bore with Re­
mover Tools L-4518-1 and L-4454-1 (Fig. 28).
(2) Clean bearing bore thoroughly.
Fig.
23
Removing
Rear Retainer
Seal

Fig.
24
Removing
Mainshaft Rear (Output) Bearing (3) Install new bearing with Handle C-4171 and
Installer C-4608 (Fig. 29).

TRANSFER
CASE
ASSEMBLY
(1) Lubricate transfer case components with auto­
matic transmission fluid during assembly. (2) If transfer case bearings were replaced, verify
that new bearings do not block any oil feed holes. (3) Assemble input gear, thrust washer and low
range gear. Be sure low range snap ring is fully seated. (4) Install input and low range gear assembly in
front case. Secure input gear with snap ring (Fig.
11).
(5) Install shift sector and new sector shaft seals.
Install range lever on sector shaft and tighten lever
locknut to 30 N*m (22 ft. lbs.) torque. (6) Install range fork and hub (Fig. 9).

21
- 3S2

NP241
TRANSFER CASE

•
Fig. 26 Removing Front Output Shaft Front Bearing Fig. 27 installing Front Output Shaft Front Bearing (7) Install front output shaft in case (Fig. 8). Fig. 28 Removing Front Output Shaft Rear Bearing
Fig. 29 Installing Front Output Shaft Rear Bearing (8) Assemble mainshaft, stop ring, synchronizer
and mainshaft drive sprocket.
(9) Insert mode fork in synchronizer sleeve. Then
install mainshaft and fork as assembly. Be sure shift
rail is aligned in range fork and is seated in case

bore.
(10) Install drive chain and front shaft sprocket
(Fig. 7).
(11) Install snap ring that secures driven sprocket
to front output shaft (Fig. 6).
(12) Install detent plunger, spring and plug (Fig.

14).
Replace O-ring on plug if necessary. Do not re­
use old O-ring if damaged. Tighten plug to 21 N»m (16 ft. lbs.) torque.
(13) Install mode spring on shift rail (Fig. 5).
(14) Install oil pump, pickup tube and screen in
rear case.
(15) Apply 3 mm (1/8 in.) wide bead of Mopar gas­
ket maker, silicone adhesive/sealer, or Loctite 515 to front case sealing surface.