1990 MITSUBISHI SPYDER wiring

.
4 . 9 N m
\ / X L - -3.6
. .
8. Accelerator cable connection9. air control motor connector
10. Heated oxygen sensor connector
11. Engine coolant temperature gauge
unit connector
12. Engine coolant temperature sensorconnector13. Ignition power transistor connector
14. Throttle position sensor connector
Capacitor connector16. Manifold differential pressure
20. Crankshaft position sensor
connector21. Air conditioning compressor
connector22. Evaporative emission purge sole-
noid valve
23. Control wiring harness
24. Brake booster vacuum hose
connection High-pressure fuel connection
26. Fuel return hose connection --
. .. .
17.18.
sensor connector
Injector connectors
Ignition coil connector
19. Camshaft position sensor connector 27.
water nose A 28. Water hose connection29. Vacuum hoses connection
TSB Revision

ENGINE (NON-TURBO)>
Scan tool 42
Code General scan tool
No.Ignition Coil CircuitP r o b a b l e
43
[Comment]
BackgroundlIgnition coil wiring harness or connectorfailedl The PCM provides the ground control circuit for the side of ignition coil. Open circuit in coill Battery voltage is through the relay (ASD relay). P C M Range of Checkl Battery voltage: 13 or more (engine is running)
l relay (ASD relay): ON
l Engine: 3000 or lessl Engine speed and ignition timing are always stable.
Set Condition
lThe primary circuit is not achieving peak current w ith maximum dwell for 3 seconds.
SCAN TOOL Actuator test 10
relay (ASD relay)
OK: ooeratina sound can be heard.
NG Repair relay (ASD relay) related
OK
Measure at the ignition coil connector lDisconnect the connector, and measure at the harnes s side.
SCAN TOOL Actuator test 10
relay (ASD relay) relay (ASD relay) is turned on and off 1.4 seconds.
l Voltage between 2 and ground
[Measure with
relay (ASD relay) on.]
OK: Battery positive voltage Check the harness wire the (ASD-relay) and
the ignition coil connector. Repair,’ necessary.
NGMeasure at the PCM connector Check the following connector: lDisconnect the connector and measure at the harness side.lDisconnect PCM connector and short terminal (67) of
the harness-side connector to ground.
Voltage between 3 and ground OK: Battery positive voltage
OK
Check the harness wire between PCM and the ignition connector. Repair, if necessary.
Check the following connector:
OK
NG Repair
Check trouble symptom.
Replace the PCM.
N G
TSB Revision

ENGINE (NON-TURBO)> ,
Scan tool 43
Code General scan tool
No.Ignition Coil Primary CircuitP r o b a b l e
43
[Comment]lBackgroundIgnition coil wiring harness orfailedl
The PCM provides the ground control circuit for the primary side of ignition coil. Open circuit in ignition l Battery voltage is supplied through the relay relay).
l PCM failedRange of Check Battery voltage: 13 or more (engine is running)l relay (ASD relay): ON
l Engine: 3000 or less
l Engine speed and ignition timing are always stable.
Set Condition
. .
lThe primary circuit is not achieving peak current w ith maximum dwell for 3 seconds.
SCAN TOOL Actuator test
10 relay (ASD relay)
NG Repair relay (ASD relay) related
OK: Relay operating sound can be heard.
Measure at the ignition coil connector lDisconnect the connector, and measure at the harnes s side.
SCAN TOOL Actuator test 10
relay (ASD relay) relay (ASD relay) is turned on and off every 1.4 s econds.
l Voltage between 2 and ground
[Measure with
relay (ASD relay) on.]
OK: Battery positive voltageCheck the harness wire between the ignition coil connector. if necessary.
Measure at the PCM connector
lDisconnect the connector and measure at the harness side.lDisconnect PCM connector and short terminal (67) of
the harness-side connector to ground.
l Voltage between 2 and ground
OK: Battery positive voltage
OK
Check the harness wire between thePCM andthe ignition coil
connector. Repair, if necessary.
TSB Revision
Check the following connector:
OK
NG Repair
Check trouble symptom.
N G
Replace the PCM.

ENGINE (NON-TURBO)>
Scan tool 106
Code General scan tool
No.Multiple Cylinder Mlsfire
43
[Comment]Background
l Excessive engine misfire results in increased catal yst temperature.
l Severe misfire could cause catalyst damage.
l To prevent catalytic converter damage, the PCM moni tors engine misfire.
l The PCM monitors for misfire during most engine ope rating conditions.
lWhen a misfire is detected, the PCM stores a diagnostic trouble code and causes the to either flash or illuminate continuously during active misfire.
Range of Check
l MAP voltage is less than 1.60
l Engine speed is between 2200 and 2800 l Engine coolant temperature is greater than l Vehicle speed less than Set Condition
l 1000 Rev Misfire
The PCM detects misfire in more than 1.6% of the en gine cycles in a 1000 revolution
period.l 200 Rev MisfireThe PCM detects misfire in more than 15% of the eng ine cycles in a 200 revolution period.
.
Spark plugs or wires failed
l Ignition coil failed
l Crankshaft position piston rings v a l v e s
l Head gasket failed
l C r a c k e d
l Fuel lines and filter failed
l Fuel failed
l failed
l Wiring and connectors failed
l Engine coolant
l Timing belt tooth broken,
l EGR
SCAN TOOL SENSOR READ TESTS (Data list)
05 Engine coolant temperature sensor (Refer to Check the engine coolant temperature circuit.
(Refer to INSPECTION PROCEDURE 38.)
OK
SCAN TOOL SENSOR READ TESTS (Data list)
27 Intake air temperature sensor (Refer to
OK
Check the intake air temperaturecircuit.(Refer to INSPECTION PROCEDURE
SCAN TOOL SENSOR READ TESTS (Data list)
11 MAP sensor reading (Refer to
OK
OK
Check the MAP sensor circuit.(Refer to INSPECTION PROCEDURE 40.)
SCAN TOOL SENSOR READ TESTS (Data list)
Check the following connectors: 66 Oxygen sensor volts (front) (Refer to OK: Repeat and alternately whenidling.
Check the fuel pressure. (Refer to Check the harness wire between the PCM and the cran kshaft
position sensor connector.
l Check the injectors for operation sound.
l Check the injectors for fuel leakage.
l Check the evaporative emission control system.
Check the following items.
l Check the ignition coil, spark plug cables.
l Check the compression pressure.
Check the EGR
TSB Revision

E N G I N E
Scan tool
Cylinder Misfire
Code General scan tool Cylinder Misfire
No.Cylinder MisfireProbable cause
Cylinder Misfire
43,
[Comment]
Backgroundl Spark plugs or ,
l Excessive engine misfire results in increased catal yst temperature.l l . valves
l Severe misfire could cause catalyst damage.
l To prevent catalytic converter damage, the PCM moni tors engine’ misfire.l
H e a d g a s k e t f a i l e d
l The PCM monitors for misfire during most engine ope rating conditions., h e a d
When a misfire is detected, the PCM stores a diagno
stic trouble code and causes thel
Injector failedl to either flash or illuminate continuously during active misfire.
Range of Check
l MAP voltage is less than
l Engine speed is between 2200 and l Engine coolant temperature is greater than l Vehicle speed less than Set Conditionl 1000 Rev Misfire l
Wiring harness and connectors failed
6
The PCM detects misfire in more than 1.6% of the en gine cycles in a 1000 revolutionperiod. 200 Rev MisfireThe PCM detects misfire in more than 15% of the eng ine cycles in a revolution period.
NG
OK
OK
TSB Revision
Check the following items.
l Check the spark plug, spark plug cables.
l Check compression pressure.
l Check the cylinder head gasket and intake manifold gasket for damage.

ENGINE (NON-TURBO)> Troubleshooting
Scan tool 115
scan tool Power Pressure Probable.
65
[Comment]l PSP switch failedBackgroundl Wiring harness and connectors failed lData from the PSP switch allows the PCM to compensa te for the additional load put on
the engine during steering maneuvers that require h igh steering pump pressure.
Range of Check
l Vehicle speed: 90 (56 mph),Set Conditionl PSP switch output voltage: High for 30 seconds
N G Measure at the t h e P S P Disconnect the connector and measure at the compone nt side.
Measure at the switch connector lDisconnect the connector, and measure at the harness side.
l Voltage between 1 and ground
(Ignition switch: ON)
OK: Battery positive voltage
OK
Replace the PCM. Check the harness wire between the and the PSP switchconnector.
O K
Replace “the PCM.
TSB Revision

E N G I N E
Scan tool 154
C o d e G e n e r a l s c a n t o o l T e m p e r a t u r e S e n s o r
No.Voltage Too High
44
[Comment]
Backgroundl Battery temperature sensor l PCM failedBattery temperature input is used to adjust the gen erator charging rate based upon the ambienttemperature around the battery.Range of CheckIgnition switch: ON
Set Conditions .
The sensor voltage remains more than 4.9 for 3 seconds.
Replace the PCM.
Scan tool 155
C o d e G e n e r a l s c a n t o o l U p s t r e a m S h o r t e d t o
No. G r o u n d
[Comment]
Background
lWhen the heated oxygen sensor temperature is low, t
he sensor has the same electrical
characteristics as an insulator.
lThe heated oxygen sensor output signal line is rest ricted to That is why the line voltageis approx. when the heated oxygen sensor temperature is low.lIf the heated oxygen sensor output signal line is grounded, its voltage will become low.
Range of Check
l Engine coolant temperature when the engine starts:
or less
l Within three seconds after the engine
Set Conditions
The heated oxygen sensor output signal line is or less.
TSB Revision
l
.
Upstream, heated oxygen sensor failed
Wiring harness and connectors failed PCM failed
NGCheck the harness wire between the PCM and upstream heated Repair
oxygen sensor connector.
OK
Replace the PCM.

ENGINE (NON-TURBO)>
INSPECTION PROCEDURE 27
Fan motor relay system (Radiator fan, condenser fan)
[Comment]l Malfunction of fan motor relay
The fan motor relay is controlled by the power tran sistor inside the PCM turning ON and OFF l
Malfunction of fan motor
.improper connector contact, open or
short-circuited wire
l Malfunction of the PCM
Measure at PCM connectors
lDisconnect the connector, and measure at the harnes s RepairA-lA-l 07side.lVoltage between 19 and ground, 55 and ground and
69 and ground (Ignition switch: ON)
OK: Battery positive voltage
lConnect a jumper wire between 19 and ground, and
69 and ground (Ignition switch: ON)
OK:Radiator fan and condenser fan run at high speed.lConnect a jumper wire between 55 and ground (Igniti on
switch: ON).
OK
Check symptom.
1Replace the
OK: Radiator fan runs at low speed.
lCheck the radiator fan circuit (Refer to ELEC-TRICAL WIRING.) (Refer to ELECTRICAL WIRING.)
l Check the A/C condenser fan circuit.
(Refer to ELECTRICAL WIRING.) (Refer to ELECTRICAL WIRING
INSPECTION PROCEDURE 28
Ignition circuit system1
[Comment]
The PCM interrupts the ignition coil primary curren t by turning the ignition power transistor inside
the PCM ON and OFF.
TSB
Malfunction of relay Improper connector contact, circuit Or
short-circuited
l Malfunction of the PCM
NG
Measure at the ignition coil connector Check the following RepairlDisconnect the connector and measure at the harnessside. OK SCAN TOOL Actuator test
relay relay) is turned on and off every 1
[Measure with relay on.]
Check trouble
C h e c k t h e h a r n e s s b e t w e e n relay OK relay) and ignition coil switch Repair, if
Check the harness wire between PCM and ignition coi l
connector. if