1982 CHEVROLET CAMARO cooling

GM – CAMARO 1982-1992 – Repair Guide (Checked by WxMax) 388
To install:
18. Clean the sealing surfaces.
19. Install the gaskets and apply a
3/16 in. (5mm) bead of RTV sealant on the
front and rear ridge of the cylinder case.
20. Hold the gaskets in place by ex tending the RTV bead up onto the gasket
ends. Use sealer at the water passages.
21. Position the intake manifold as sembly onto the engine and install the
intake manifold-to-cylinder head bolts. Torque bolts in sequence to 25-45
ft. lbs. (34-61 Nm).
22. Connect the heater hose to the intake manifold.
23. Connect the upper radiator hose to the thermostat housing.
24. Install the distributor.
25. Position the TBI and plate assembly on the intake manifold with a new
gasket. Install the bolts which attach the upper manifold plate (or TBI
plate) to the intake manifold and torque to specification.
26. If the TBI units on CFI engines were removed, install the fuel balance
tube (connecting the units).
27. Connect vacuum hoses which were disconnected for removal of the manifold.
28. Connect the positive crankcase ventilation valve hose.
29. Install the cable bracket to the m anifold and connect the accelerator and
cruise control cables.
30. Install the power brake booster line.
31. Connect the fuel return line at the TBI unit.
32. Connect the wiring to the idle air motors, injectors, and the throttle
position sensor (TPS).
33. Install the exhaust gas re circulation (EGR) solenoid.
34. Connect the fuel inlet line to the TBI unit.
35. Install the air cleaner assembly.
36. Connect the negative battery cable at the battery.
37. Fill the cooling system.
38. Start the engine and check for leaks.

Fig. 8: Crossfire fuel injection intake manifold bolt torque sequence

GM – CAMARO 1982-1992 – Repair Guide (Checked by WxMax) 389
1988-1992 MODELS
1. Disconnect the negative battery cable.
2. Drain the cooling system.
3. Remove the air cleaner.
4. Remove the throttle body.
5. Label and unplug all vacuum hose and electrical connections on the manifold.
6. Disconnect the upper radiator hose from the manifold.
7. Mark the distributor position and remove it.
8. Remove the EGR valve, if necessary.
9. Remove the intake manifold bolts and studs.
10. Remove the manifold and discard the gaskets.
To install: 11. Make sure the sealing surfaces are clean.
12. Install the gaskets and apply a
3/16 in. (5mm) bead of RTV sealant on the
front and rear ridge of the cylinder block.
13. Hold the gaskets in place by ex tending the RTV bead up onto the gasket
ends. Use sealer at the water passages.
14. Install the intake manifold.
Sealing of the intake mani fold to the "V" of the engine is obtained by employing
an intermediate torque specification to a ll the attaching bolts, alternately, in the
proper sequence. This step is used to rock the manifold into place before
applying the final torque figur e. Failure to follow this two-step procedure can
result in possible leaks.
15. Install the intake manifold attach ing bolts. Tighten them, using the proper
sequence, to 89 in lbs. (10 Nm).
16. Final torque the bolts, using the proper sequence, to 35 ft lbs. (47 Nm\
).
17. Install the EGR valve.
18. Install the distributor.
19. Connect the upper radiator hose to the thermostat housing.
20. Install the throttle body.
21. Engage all electrical and hose connections.
22. Fill the cooling system.
23. Connect the negative battery cable.
24. Install the air cleaner.
1985-1992 MFI ENGINES
2.8L AND 3.1L ENGINES

GM – CAMARO 1982-1992 – Repair Guide (Checked by WxMax) 392
43. Fill the cooling system.
44. Start the engine and che
ck for proper operation.
5.0L AND 5.7L ENGINES

Fig. 10: Intake manifold bolt torque s equence for V8 engines, except Crossfire
Fuel Injection
1. Disconnect the negative battery cable.
2. Remove the air intake duct.
3. Drain the cooling system.
4. Disconnect the control cabl es from the throttle body.
5. Label and unplug all wiring connectors and hoses from the throttle body
and plenum.
6. Disconnect the AIR hoses from the air management valve.
7. Disconnect the fuel lines.

GM – CAMARO 1982-1992 – Repair Guide (Checked by WxMax) 394
39. Tighten the runner to plenum bolts to
25 ft lbs. (34 Nm). Start in the
center and work outwards.
40. Install the distributor.
41. Connect the fuel lines.
42. Install the EGR valve solenoid.
43. Connect the control cables to the throttle body.
44. Connect all remaining hose and wiring connections.
45. Fill the cooling system.
46. Connect the negative battery cable.
EXHAUST MANIFOLD
REMOVAL & INSTALLATION
EXCEPT 2.5L ENGINES

Fig. 1: Exhaust manifold bolts for most V6 engines up to 1992

GM – CAMARO 1982-1992 – Repair Guide (Checked by WxMax) 403

Fig. 8: Lifting out the radiator
1. Disconnect the negative battery cable.
2. Drain the cooling system.
CAUTION - When draining the coolant, keep in mind that cats and dogs are
attracted by the ethylene gl ycol antifreeze, and are quite likely to drink any that
is left in an uncovered container or in puddles on the ground. This will prove
fatal in sufficient quantity. Always drai n the coolant into a sealable container.
Coolant should be reused unless it is contaminated or several years old.
3. Remove the air inlet ducts and air cleaner, if necessary.
4. Remove the electric cooling fan, if equipped.
5. Disconnect the coolant overflow tank hose.
6. Disconnect upper and lower radiator hoses.
7. On vehicles equipped with automat ic transmission, disconnect and plug
the transmission fluid cooler lines.
8. Disconnect and plug the engine oil cooler lines, if equipped.
9. Remove fan shroud a ssembly, if applicable.
10. Remove the upper radiator mount screws.
11. Remove the radiator assembly by lifting straight up.
The radiator assembly is held at the bottom by tw o cradles secured to the
radiator support.
12. If installing a new radiat or, transfer the fittings from the old radiator to the
new radiator.

GM – CAMARO 1982-1992 – Repair Guide (Checked by WxMax) 404
13. Replace the radiator assembly by
reversing the above steps. Check that
radiator lower cradles are locat ed properly in radiator recess.
14. Refill the cooling system. Check the engine oil and transmission fluid
levels, if necessary. Run engine for a short period of time and check for
leaks.
ENGINE OIL COOLER
The engine oil cooler consists of an adapter, bolted to the engine block, to
which the oil filter is scr ewed onto. The adapter has 2 hoses which attach to the
oil cooler and the radiator , these hoses are the inlet and return lines.
REMOVAL & INSTALLATION 1. Disconnect the negative battery cabl e. Drain the cooling system into a
suitable container.
CAUTION - When draining the coolant, keep in mind that cats and dogs are
attracted by the ethylene gl ycol antifreeze, and are quite likely to drink any that
is left in an uncovered container or in puddles on the ground. This will prove
fatal in sufficient quantity. Always drai n the coolant into a sealable container.
Coolant should be reused unless it is contaminated or several years old.
2. Remove the radiator, if the oil c ooler is to be repaired or replaced,
otherwise remove the engine oil cooler from the radiator as necessary.
3. Remove the oil filter.
4. Remove the hoses from the oil cooler adapter.
5. Unscrew the oil cooler adapter re tainer and remove the assembly.
Discard the gasket.
6. Installation is the reverse of t he removal procedure. Use new gaskets.
ELECTRIC COOLING FAN
REMOVAL & INSTALLATION 1. Disconnect the battery ground cable.
2. Remove the air cleaner and ducts, if necessary.
3. Unplug the fan harness connector.
4. Remove the fan frame to radiator support mounting bolts and remove the
fan assembly. Some models are retai ned by clips. Remove these, then
slide the fan assembly from the radiator.
5. Install the cooling fan frame to t he radiator support bolt. Reconnect the
wiring harness, the negative battery cable and check fan operation.
BELT-DRIVEN COOLING FAN
REMOVAL & INSTALLATION 1. Disconnect the negative battery cable.
2. Remove the fan shroud, as required.

GM – CAMARO 1982-1992 – Repair Guide (Checked by WxMax) 405
3. Remove the fan-to-water pum
p attaching bolts or nuts.
4. Remove the fan belts.
5. Remove the cooling fan and clut ch assembly. Separate the clutch
assembly from the fan.
Store the clutch in an upright position to prevent seal leakage.
6. Installation is the revers e of the removal procedure.
WATER PUMP
REMOVAL & INSTALLATION
CAUTION - When draining the coolant, keep in mind that cats and dogs are
attracted by the ethylene gl ycol antifreeze, and are quite likely to drink any that
is left in an uncovered container or in puddles on the ground. This will prove
fatal in sufficient quantity. Always drai n the coolant into a sealable container.
Coolant should be reused unless it is contaminated or several years old.
2.5L ENGINE

Fig. 1: Water pump - 2.5L
1. Drain the cooling system.
2. Remove the accessory drive belts.
3. Remove the fan and pump pulley.
4. Remove the heater hose and lower r adiator hose from the water pump.
5. Remove the pump from the block.
To install: 6. Coat the new gasket with RTV sealer . Install the pump and torque bolts
to 25 ft lbs. (34 Nm).
7. Install the hose and lower radi ator hose to the water pump.
8. Install the pum p pulley and fan.
9. Install the accessory drive belts.

GM – CAMARO 1982-1992 – Repair Guide (Checked by WxMax) 406
10. Fill the cooling syst
em, start the engine and check for leaks.
V6 ENGINES 1. Disconnect the negative battery cable.
2. Drain the cooling system.
3. Remove the air intake duct and air cleaner, if necessary.
4. Remove the drive belt.
5. Disconnect the heater and radiator hoses from the water pump.
6. Remove the power steering pump bracket and swing aside.
7. Remove the water pump bolts. Mark the bolts to their corresponding
locations for proper installation.
To install: 8. Clean the gasket surface.
9. Install the water pump with a new gasket. Apply sealer to the bolt
threads.
10. Tighten the large bolts to 25 ft lbs. ( 34 Nm), medium bolts to 15 ft lbs. (21
Nm) and the small bolts to 88 inch lbs. (10 Nm).
11. Install the power steering pump bracket.
12. Connect the heater and radiator hoses.
13. Install the drive belt.
14. Install the air cleaner and duct.
15. Fill the cooling syst em. Start the engine and check for leaks.
V8 ENGINES

Fig. 2: Removing the heater hoses