2021 AUDI Q2 Owner´s Manual

Instruments
and
controls

CO

<
o

IV
tN
I-I
00
Vehicles with manual gearbox
-
•
Shifting
up
a gear:
The
suggested gear
ap­

pears
to the
right
of
the current gear when
a

higher gear
is
recommended.
-
4
Shifting down
a
gear:
The
suggested gear
ap­

pears
to the
left
of
the current gear when
a

lower gear
is
recommended.
The gearyou
are
currently
in and the
recommen­
ded gear will
be
displayed. Gears
may
occasional­
ly
be
skipped
(3 • 5).

Vehicles with start/stop system:
If
all
the
condi­
tions
for
a
stop phase
^>page
79
have been
met,
but the
gear lever
is in
gear with
the
clutch

depressed,
the
gear change indicator will recom­
mend changing
to
•N.
Put the
gear lever
in
neu­

tral and take your foot
off
the clutch pedal.
The

start/stop system will automatically switch
off

the engine.
Vehicles with automatic gearbox
The display
is
only visible
in
tiptronic mode

^>page
90.

The symbol
Î
after
the
current gear means
change
up a
gear.
© CAUTION
The gear-change indicator
is
intended
to
help
save
fuel.
It is not
intended
to
recommend
the right gear
for all
driving situations.
In
cer­
tain situations, only
the
driver can choose
the

correct gear
(for
instance when overtaking,
driving
up
a steep gradient
or
towing a
trail­

er).

(T) Note

Applies
to:
vehicles with manual gearbox
The gear-change indicator
in the
instrument
cluster goes
out
when you press
the
clutch

pedal.

Outside temperature display
When
the
vehicle
is
stationary
or
travelling
at

very
low
speeds,
the
temperature displayed
may

be slightly higher than
the
actual outside
tem­

perature
as
a result
of
the heat radiated from
the

engine.
At temperatures below +5°C a snowflake symbol
appears next
to the
temperature display
<=> A-

A WARNING
Do
not
rely
on the
outside temperature dis­
play
as an ice
warning. Bear
in
mind that
there
may be
patches
of
ice
on the
roads even
at outside temperatures around
+5
°C
-
risk
of

accident!
Multi-function steering
wheel plus
How
to use the
multi-function steering
wheel
Applies
to:
vehicles with Audi virtual cockpit

You
can
use
the
multi-function steering wheel
to

control
the
driver information system
and MMI

functions, adjust
the
volume
and
switch
the

speech dialogue system
on/off.

»180km
1
&_J
f
87.6M...
|f
|
H

n

^
_
X

m

®r

87.6 MHz CI /
88.7 MHz
90.0 MHz
90.5
MHz

91.5
MHz

96.6 MHz

Fig.
7
Example: Driver information system display (Audi
virtual cockpit)

In

1-

m

Fig.
8
Left side
of
multi-function steering wheel plus
Important:
The
ignition must
be
switched
on.

15

Instruments and controls
The driver information system shows information

(D
in several display tabs
(T)
^>Fig.
7.
The equipment installed on your vehicle deter­
mines which of the following tabs are available:
1st tab

2ndtaba)

3rd
tab

4th
tab
5th tab
On-board computer
^>page
19
Driver messages
Radio
•=>page
22
Media
^>page
22
Telephone*
^>page
23
Navigation*
<^>page
24

Map*
<>page
24

a)
This tab is only visible if one or more warning/indicator
lamps or driver messages are displayed.

g) [<_>J
button
- To switch between tabs: Press the button
[<±]

repeatedly until the desired tab is displayed

(e.g.
Radio).

01
VIEW|
button

To change the view: see
Opage
17, Changing
views.

(DEI
button
To return to the previous function level.

©
Control buttons
0
and
[3

To call up/close the selection menu or options
menu
^>page
16.

®
Left thumbwheel
- To select a function in a menu/list: Scroll the
left thumbwheel to the desired function (e.g.
setting a frequency).
- To confirm your selection: Press the left
thumbwheel
(J)
^Fig.
8.
- To zoom in/out of the map: When a map is
shown on the display, scroll the left
thumb­

wheel to make the map scale larger or smaller.
Control buttons
Applies to: vehicles with Audi virtual cockpit

W
180
km A I

Update station
list

mm

Fig.
9 Selection menu and options menu
Left control button
- To call up/close the selection menu: Press the
left control button
OF/g.
9 on the multi-func­
tion steering wheel. You can use the left
thumbwheel to select and confirm a function in
the selection menu (e.g. to select
a
new
wave­

band). •
16

Instruments and controls

CO

s

r>

I-I

00
Right control button
- To call up/close the options menu: Press the
right control button
OF/g.
9 on the multi-func­
tion steering wheel. You can use the left
thumbwheel in the options menu to select
con­

text-sensitive functions or change certain set­
tings (e.g. extended programme information).
®
Whether
a
selection menu or options menu is
available depends on the function you have

selected.

Changing views
Applies to: vehicles with Audi virtual cockpit
•
I
PTiF^ff

^1
-
Hi

Fig.
10
Extended view

/f^

•,~r.
P
^••^J^nfci i
lOjjg^-^

«
iiiri*

i
A
1
/
a
7.o
„•.«,.„
/,
HI
i
w
it
»

N
\
BO
MD


^m •

Fig.
11
Classic view

- To change
views:
Press the |VIEW| button
@
Opage
15, Fig. 8 to switch from the classic
view
oF/'g.
J J
to the extended view
oF/g.
10.
Press the |VIEW| button again to return to the
classic view.
Further function selector buttons
Applies to: vehicles with Audi virtual cockpit

Fig.
12 Right side of multi-function steering wheel plus
®
0
button
- To answer a
call:
Press the 0 button when
there is an incoming
call.

- To end a
call:
Press the 0 button during a
call.

- To display the call list: Press the 0 button
while no calls are active and there are no in­
coming calls.

© S
button
- To switch on the speech dialogue system:
Briefly press the
0
button. Give a spoken com­
mand after the beep signal.
- To switch off the speech dialogue system:
Press and hold the
\2*\
button for several sec­

onds.
Or: Say the command Cancel.
For more information about the speech dialogue

system,
refer to
^>page
164,
Speech
dialogue
system.
(D Right thumbwheel
You can adjust the volume of an audio source or
system message (e.g. during a speech dialogue)
directly while it is being played.
- Volume up/down: Scroll the right thumbwheel

up/down.

- Mute/pause: Scroll the right thumbwheel

down.
Or: Press the right thumbwheel.
- Unmute/resume: Scroll the right thumbwheel
upwards. Or: Press the right thumbwheel.
©
i«
/
»i
button
- To select the previous/next track or station:
Press
the \^\ or0<<]
button.
17

Instruments and controls
- To fast forward/rewind an audio file: Press
and hold
the[^i]or[>>!]
button until the desired
playing position has been reached.

0 B
button
- To call up the user-assigned function: Press
the
S
button on the multi-function steering

wheel.

- To check which function is assigned: Press and
hold
the E
button.
- To change the assigned function: Select:

IMENUJ
button > Car
>
left control button
>
Ve­
hicle settings
>
Steering wheel button.

(D H
button
- To have the last navigation cue repeated:
Press the
H
button while route guidance is ac­

tive.

- To adjust the volume of the navigation cues:
Scroll the right thumbwheel up/down during
route guidance while a navigation cue is being

spoken.

Multi-function steering
wheel
How to use the multi-function steering
wheel

Applies
to: vehicles with analogue instrument cluster

You
can use the multi-function steering wheel to
control the driver information system and
cer­

tain MMI functions and to adjust the volume.

Fig.
13 Left side of multi-function steering wheel

Fig.
14 Right side of multi-function steering wheel
Important: The ignition must be switched on.

(T)
How to use the driver information system
The driver information system shows information
(D
alpage
15, Fig. 7 in several display tabs
(Î)
^>page
15, Fig. 7.
The equipment installed on your vehicle deter­
mines which of the following tabs are available:

1st
tab
2nd
taba)

3rd
tab
4th tab

5th
tab
On-board computer
<^>page
20
Driver messages
Radio
opage
22
Media
•=>page
22
Telephone*
opoge
23
Navigation*
opage
24

a'
This tab is only visible if one or more warning/indicator

lamps
or driver messages are
displayed.

- To switch between tabs: Press the
L±>]
button
repeatedly until the desired tab is displayed.
- To call up/close a menu: Press the
EH
button.
- To select a function in a menu/list: Scroll the
left thumbwheel to the desired function.
- To confirm the selection: Press the left
thumb­

wheel to confirm your selection.
- To return to the previous function level: Press

the
Unbutton.

- To scroll through lists: Scroll the left
thumb­

wheel quickly.

©0]
button
- To answer a
call:
Press the
0
button when
there is an incoming
call.

- To end a
call:
Press the 0 button during a
call.

- To display the call list: Press the 0 button
while no calls are active and there are no in­
coming calls.
18

Instruments and controls

(DE
button
- To switch on the speech dialogue system:
Briefly press the
\2*\
button. Give a spoken com­
mand after the beep signal.
- To switch off the speech dialogue system:
Press and hold the
0
button for several sec­

onds.
Or: Say the command Cancel.
For more information about the speech dialogue

system,
refer to
<=>page
164,
Speech
dialogue
system.

0
Right thumbwheel
You can adjust the volume of an audio source
or

system message (e.g. during a speech dialogue)
directly while
it
is being played.
- Volume up/down: Scroll the right thumbwheel

up/down.

- Mute/pause: Scroll the right thumbwheel

down.
Or: Press the right thumbwheel.
- Unmute/resume: Scroll the right thumbwheel
upwards. Or: Press the right thumbwheel.

0[i<<]/[>>i]
button

CO

<
O
rN
r>
i-H

00
- To select the previous/next track or station:
Press the
[>>[]
or
[j<<]
button.
- To fast forward/rewind an audio file: Press
and hold the
L^]
orL>ED
button until the desired
playing position has been reached.

(DE
button
- To call up the user-assigned function: Press
the
\M
button on the multi-function steering

wheel.

- To check which function is assigned: Press and
hold
the SD
button.
- To change the assigned function: Select:

|MENU|
button > Car
>
left control button
>
Ve­
hicle settings > Steering wheel button.

@B
button
- To have the last navigation cue repeated:
Press the
H
button while route guidance is ac­

tive.

- To adjust the volume of the navigation cues:
Scroll the right thumbwheel up/down during
route guidance while a navigation cue is being

spoken.

Driver information
system

On-board computer (Audi virtual cockpit)

Applies
to: vehicles with Audi virtual cockpit
ftHSOlr,

0
6,0
1/100
km

Fig.
15
Instrument cluster: Consumption display
Resetting values to zero
Important: The consumption, short-term mem­
ory or long-term memory display must be selec­

ted.

•
To reset the figures in the selected memory
to

zero,
press the left thumbwheel (?)
^>page
15,
Fig.
8
on the multi-function steering wheel for
one second. Or:

•
On the multi-function steering wheel, select
right control button > Reset values*.
Changing settings for additional display
The additional displays that can be selected vary
depending on the equipment installed on your
vehicle.

•
On the multi-function steering wheel, select
right control button
>
Additional display.

•
Select the desired additional display.
Calling up vehicle functions

•
Call up the first tab (on-board computer) using
the
ElE]
button on the multi-function steering

wheel.

The equipment installed on your vehicle deter­
mines which of the following displays are availa­

ble:

- Date and time
^>page
255
- Average fuel consumption
- AdBlue range
^>page
292

-Single
journey memory summary
19

Instruments and controls

-Totaljourney
memory summary
- Energy consumers
^>page
20
- Driver assistance
^>page
104
- Traffic sign recognition
<=>page
108
The single journey memory processes the infor­
mation on
a
journey from the time the ignition is
switched on until it is switched off. If the journey
is resumed within two hours after the ignition is
switched off, the new figures are automatically
included in the calculation.
Unlike the
single
journey memory, the totaljour-
ney memory is not erased automatically. In this
way, you can determine the period for which you
wish the on-board computer to supply driving in­

formation.

Fuel consumption
The current fuel consumption can be shown in a
bar display
^>Fig.
15. The average fuel consump­
tion from the single journey memory can also be

displayed.
If the barturns green, yourvehicle is
saving fuel using the following function:
- Recuperation: Electrical energy can be stored in
the battery (recuperation) if the vehicle is trav­
elling downhill or coasting in gear (overrun). In
this case, the bar will move towards the
Q

symbol.

- Active Cylinder Management*: The engine au­
tomatically shuts down two cylinders when per­
formance demand is low and certain other
con­

ditions have been met. This process is imper­
ceptible to the occupants. The driver message

2-cylinder
mode will appear if the average fuel
consumption display
^>Fig.
15 is selected in the
instrument cluster. The cylinders are reactiva­
ted under heavier load conditions.
Energy consumers*
In the Energy consumers view, auxiliary equip­
ment currently affecting the vehicle's fuel
con­

sumption is listed. The display shows up to
three energy consumers. The energy consumer
drawing the most power appears at the top of
the list. If more than three energy consumers are
switched on, the ones currently using the most
power are displayed. In addition, a scale
indi­

cates the overall current fuel consumption of all
energy consumers.
Economy tips
Applies to: vehicles with Audi drive select and efficiency mode
In efficiency mode, economy tips are shown
briefly on the instrument cluster display in cer­
tain situations where fuel economy is affected.
By following these economy tips, you can save

fuel.

To clear an economy tip from the display immedi­
ately, press the left thumbwheel on the multi­
function steering wheel.
To activate/deactivate economy
tips:
Select the
following on the infotainment system:
|MENU|

button > Car
>
Audi drive select. Select: efficien­
cy
>
right control button > Economy tips.
© Note
- The date, the time and the time/date dis­
play format can be changed via the infotain­
ment system
^page
255.
- The economy tips are not always displayed
in every conceivable situation, but are delib­
erately spaced out over time.
- Once you have cleared an economy tip from
the display, it will not appear again until the
next time you switch on the ignition.
On-board computer (analogue instrument
cluster)
Applies to: vehicles with analogue instrument cluster
15:50

0
6,0

Fig.
16 Instrument cluster: Consumption display
Resetting values to zero

•
Press the
[Hi
button on the multi-function
steering wheel and select On-board computer
or Efficiency program from the menu. •
20

Instruments and controls

CO

<
o

IV
tN
I-I
00
• To reset the figures in the selected memory to

zero,
press the left
thumbwheel (Î) •=>page
18,
Fig. 13 on the multi-function steering wheel for
one second.
Calling up vehicle functions
• Call up the first tab (on-board computer) using
the
0E]
button on the multi-function steering

wheel.

•
Press the
@
button on the multi-function
steering wheel and select Vehicle functions
from the menu.
The equipment installed on your vehicle deter­
mines which of the following displays are availa­

ble:

- On-board computer fl, B
opage
21
- Efficiency program
3
<^page
21
- Digital speedometer
- Assists
cépage
104
- Traffic signs
^>page
108
- Reduced display
On-board computer
On the on-board computer you can call up the
following displays in turn by scrolling the left
thumbwheel on the multi-function steering

wheel:

- Date
•=>
page 255
- Range
- AdBlue range*
^>page
292
-Short-term
memoryD

- Average fuel consumption
- Long-term memory B
The single journey memory processes the infor­
mation on
a
journey from the time the ignition is
switched on until it is switched off. If the journey
is resumed within two hours after the ignition is
switched off, the new figures are automatically
included in the calculation.
Unlike the single journey memory, the
total
jour­
ney memory is not erased automatically. In this
way, you can determine the period for which you
wish the on-board computer to supply driving in­

formation.

The following additional display may be available
in the on-board computer, depending on the ve­
hicle equipment:
- Active Cylinder Management: The engine auto­
matically shuts down two cylinders when per­
formance demand is low and certain other
con­

ditions have been met. This process is imper­
ceptible to the occupants. The driver message

2-cylinder
mode will appear if the current or
average fuel consumption display
oFig.
16 is
selected in the instrument cluster. The cylin­
ders are reactivated under heavier load condi­

tions.

Efficiency program
3

Applies to: vehicles with efficiency program
The efficiency program can help to save
fuel.
It
evaluates fuel efficiency data, shows a list of aux­
iliary equipment affecting fuel consumption, and
suggests gear changes. It also provides economy
tips for saving
fuel.

The efficiency program uses the trip and fuel
con­

sumption data from the short-term memory.
When you clear the data from the efficiency pro­

gram,
the values in the short-term memory are
reset to zero.
The following additional displays are available in
the efficiency program, depending on the vehicle
equipment:
- Advanced gear-change indicator: The advanced
gear-change indicator is based on the same
log­

ic as the "regular" gear-change indicator. The
"regular" gear-change indicator disappears
from the display when the advanced gear-
change indicator appears
^>page
14.
- Energy consumers: The efficiency program
shows a List of energy consumers currently af­
fecting the vehicle's fuel consumption. The dis­
play shows up to three energy consumers. The
energy consumer drawing the most power ap­
pears at the top of the list. If more than three
energy consumers are switched on, the ones
currently using the most power are displayed.
In addition, a scale indicates the overall current
fuel consumption of all energy consumers.
- Economy
tips:
Economy tips will automatically
appear intermittently in the efficiency program •
21

Instruments and controls
in certain situations. By following these econo­
my tips, you can save
fuel.
To clear an economy
tip from the display immediately, press any of
the controls on the multi-function steering

wheel.

The date, the time and the time/date display
format can be changed via the infotainment
system
•=>
page 255.
Radio
Important: Radio mode must be activated

^>page
228, and the radio/media tab must be

displayed.

•
Press the
HH
button or the left control button

^>page
16, depending on the equipment in
your vehicle.
The following functions are available on the driv­
er information system, depending on the vehicle
equipment:
- To set the waveband: Select and confirm the

waveband.

- To tune to a station from the memory list*:
Select Memory
>
desired radio station.
- To tune to a station from the station list*: Se­
lect and confirm a radio station.
- To tune to a station from the favourites list:
Select Favourites > desired radio station.
- To call up a media source: Select and confirm
To media.
Other settings
Applies to: vehicles with Audi virtual cockpit
- SeLect: right control button > desired
entry.

The following settings are available depending
on which function is selected:
- Update station list*: see
<=>page
232.
- Detailed station information: See

opage
232.
Media
Important: A media drive must contain audio/
video files
^page
235, and the radio/media tab
must be displayed.

•
Press the
\M
button or the left control button

^page
16, depending on the equipment in
your vehicle.
The following functions are available on the driv­
er information system, depending on the vehicle
equipment:
- To select a media source: Select and confirm a
media source, e.g. "SD
card".

- To play an audio/video file: Select and confirm
a track/file.
-To pause/resume playback: Press the right

thumbwheel (D^poge
17, Fig. 12. To continue
playback, press the right thumbwheel again.
- To restart playback of an audio file: Select the
track currently playing if it is not already selec­
ted and press the left thumbwheel.
Applies to: vehicles with analogue instrument cluster
- To switch to the radio: Select and confirm a
waveband (e.g. FM).
Applies to: vehicles with Audi virtual cockpit
- To switch to radio: Select and confirm To radio.
- To call up detailed track information: SeLect
the right control button > Detailed track infor­

mation.
For more information, please refer to

tapage
246.
® Note
- The MMI media drives do not support DRM-
protected files; these files are marked with
the
symbolS.

- Please note that when you are using the
driver information system to control play­
back within a media source, only the playlist
selected on the MMI control console can be
played
^>page
244.
- Always note the information on the info­
tainment display. It may be necessary to
use the MMI control console to operate cer­
tain functions.
22