2019 CITROEN RELAY Handbook (in English)

39
Seat with variable vibration
reduction
Rotating seat2-seat front bench seat
Writing table
F If your seat is fitted with this system, turn the control to adjust the level of damping to
suit the driver's weight.
F

I
f fitted on your seat, press the control to
rotate the seat by 180°. It is equipped with two head restraints and two
seat belts.
The backrest of the centre seat folds to form
a


writing table.
F

P
ull the strap located at the top of the seat
backrest.
Rear seats
Seat backrest angle
F Turn the control knob to adjust the seat backrest angle.
3
Ease of use and comfort

40
Access to row 3Central seat backrest folded
position (rows 2
and 3)
The backrest of the central seat can be folded
down fully onto the seat cushion and used as
a
cup holder/table.
To understand the significance of the
precautions mentioned on the Labels ,
refer to the corresponding section.
F

T

o gain access to row 3, operate the control
on the outer seat of row 2

and tilt the
backrest forwards.
F

T

o return the backrest to its initial position,
bring it to the vertical position without
touching the control. F

L
ower the head restraint then raise the
control and fold the seat backrest for wards.
F

T
o return the seat backrest to its initial
position, raise the control again.
Rear bench seats
Access to the rear seats
F Lower the head restraints then raise the first lever and tilt the seat backrest for wards.
Seat backrest folded
position
F Remove the head restraints then tilt the seat backrest as described above.
F

W
ith your right hand, raise the second lever
then tilt the seat backrest 5° towards the
r e a r.
F

W
ith your left hand, tilt the seat backrest
fully forwards onto the cushion.
Ease of use and comfort

41
Removing the bench seat
At least two people are required to remove
the bench seat.
F

F
old the seat backrest onto the cushion as
described above.
Check that the seat belts are always
accessible to the passenger and easy to
fasten.
A passenger must not take their seat
without adjusting the seat's head restraint
correctly and adjusting and fastening the
seat belt.
Do not remove a
head restraint without
storing it and securing it to a
support.
Do not allow anyone to travel in row 3
with
the row 2
bench in the vertical position.
Do not leave any objects on the folded
backrest of row 2.
Steering wheel
adjustment
F With the vehicle stationary, first adjust your seat to the most suitable position.
As a
safety precaution, these operations
must only be carried out while the vehicle
is stationary.
F

T

urn the two grips for ward to release the
rear anchorages.
F

T

ilt the base of the bench seat for wards to
place the assembly in the vertical position. F

T

urn the two levers upwards to release the
front anchorages.
F

Ra

ise the bench seat and remove it. F

R
elease the steering wheel adjustment
mechanism by pulling the lever towards you.
F

A
djust the reach of the steering wheel, then
lock the mechanism by pushing the lever
fully forwards.
3
Ease of use and comfort

42
Mirrors
Door mirrors
These are divided into two zones:
A -Upper mirror
B - Lower mirror
Electric adjustments
The key must be in the MAR position.
Left-hand mirror:
A1 - Upper mirror
B1 - Lower mirror
Right-hand mirror:
A2 - Upper mirror
B2 - Lower mirror
F

T
hen move the control in the direction of the
adjustment required.
The rear view mirror glass is spherical in
order to widen the lateral field of view. The
objects obser ved are, in reality, closer than
they appear. Therefore, this must be taken
into account in order to assess the distance
c o r r e c t l y.
The shell incorporates the direction indicator
side repeater and aerials, depending on the
equipment available on board (GPS, GSM,
Radio, etc.). F

T
urn the control to select the mirror zone.
Electric folding
F Press this control.
Defrosting the mirrors
F Press the heated rear window button.
Rear view mirror
The lever located on the lower edge moves the
mirror into two positions.
For the day position, the lever is pushed.
For the night position to prevent dazzle, pull the
lever towards you.
Ease of use and comfort

43
Heating/Manual air
conditioning
1.Air conditioning on/off.
2. Adjusting the temperature.
3. Adjusting the air flow.
4. Adjusting the air distribution.
5. Air intake/Air recirculation.
Air conditioning
The air conditioning only works with the engine
running.
The fan must be set to at least 1.
Pressing the button switches the air
conditioning on; the LED is lit.
Pressing the button again switches the function
off; the LED goes out.
Temperature
F Turn the dial to select a position between blue
(cold) and red (hot) so as to
adjust the temperature to your
requirements.
Air flow
F Turn the control to your chosen position to obtain sufficient air
flow for your comfort.
If you place the air flow control at
position 0 (off), the thermal comfort is no
longer controlled. However, a slight flow of
air can still be felt due to the movement of
the vehicle.
Air distribution
The air supply distribution is directed by the
control turned towards: the footwells,
the windscreen, footwells and side
windows,
the windscreen and side windows.
Air intake/Air recirculation
The intake of exterior air prevents the formation
of mist on the windscreen and side windows.
Recirculation of the interior air isolates the
passenger compartment from exterior odours
and fumes.
Used with the air conditioning switched on
and the fan setting (from 1
to 4), recirculation
enables you to obtain the required ambient air
comfort level with both hot or cold settings.
Return to exterior air intake as soon as possible
to avoid deterioration of the air quality and the
formation of mist.
the side vents and central vents,
the side vents, central vents and
footwells, F

P
lace the control in this position
to recirculate the interior air.
F

P
lace the control in this position
for exterior air to enter.
3
Ease of use and comfort

44
Automatic single zone air
conditioning
1.AUTO mode.
2. Air conditioning off.
3. System completely off.
4. Adjusting the air distribution.
5. Adjusting the air flow.
6. Air intake/Air recirculation.
7. Fast demisting/defrosting.
AUTO mode
FULL AUTO operation: F
U
sing the moving ring surrounding the
AUTO control, set the comfort temperature
to be reached according to a setting
between:
-
H
I (High to ≈32) and
-
L
O (Low to ≈16).
The system controls the distribution, flow and
intake of air to ensure comfort equivalent to the
setting displayed and sufficient recirculation of
air in the passenger compartment.
F
P
ress the AUTO control.
This switches on the
system functions,
confirmed by the FULL
AUTO display. This is the
normal operating mode
for the automatic air
conditioning system.
AUTO mode with
personalisation
In AUTO mode, certain settings can be
modified: distribution, air flow, air conditioning
and air intake/recirculation.
The display changes from FULL AUTO to
AUTO .
To return to fully automatic
operation, press this button
again. The display on the
control panel changes from
AUTO to FULL AUTO .
If the system is not able to maintain the setting
selected following manual adjustments, the
setting flashes then AUTO is cleared. Press
the AUTO control to return to the automatic
settings.
Switching off the air conditioning
F Press this button to halt the cooling functions. The
snowflake is cleared from the
screen.
Complete switch-off
F Press this button to switch off the system. The LED and
display switch off.
Temperature
The settings range between:
- i ncreasing the interior ambient air
temperature HI (High) which heats to
a
maximum setting of 32,
-

c
ooling the interior ambient air temperature
LO (Low) which goes down to a
setting of
16.
Air distribution
F Press one or more buttons to direct the air flow towards:
the windscreen and front side
window vents (demisting/defrosting
the windows),
Ease of use and comfort

45
the central and side vents (chest
a n d f a c e),
the vents in the front and rear areas
(feet).
The combination of buttons permits
improvement of air distribution.
Air flow
F Press this button to increase air f low.
F

P
ress this button to decrease air
f low.
Air intake/Air recirculation
Additional rear ventilation
This system supplements
the passenger compartment
ventilation equipment.
The intake of exterior air prevents the formation
of mist on the windscreen and side windows.
Recirculation of the interior air isolates the
passenger compartment from exterior odours
and fumes.
This function allows hot or cold air to be
delivered selectively and more quickly. Return to exterior air intake as soon as possible
to avoid deterioration of the air quality and the
formation of mist.
F

P
ress this button to recirculate
the interior air. The indicator
lamp comes on.
Pressing the AUTO button also restores
the exterior air intake. Returning to this
position permits renewal of the air in the
passenger compartment and demisting.
Pressing the AUTO button again restores
the FULL AUTO function.
Pressing this button again turns the indicator
lamp off and re-opens the exterior air intake.
3
Ease of use and comfort

46
Air outlet
Press this control to activate
extraction of air to the outside; the
LED comes on. Press again to
switch off.
Air intake
Pressing this control activates the
exterior air intake into the passenger
compartment; the LED comes on.
Press again to switch off.
Additional heating
systems
Additional heating
This is passenger compartment heating,
additional to the standard equipment.
It can operate independently of the engine.
Additional heater or
programmable additional
heating
This is an additional, programmable and
separate system which heats the Diesel engine
hot coolant loop to make starting easier.
It improves the demisting and defrosting
per formance and that of the heated seats, if
fitted to the vehicle.
Automatic additional
heating
This is an additional system which starts
automatically when the ignition is switched
on. Its activation depends on the exterior
temperature and the temperature inside the
vehicle.
It switches off automatically once the heating
system is started manually. The passenger compartment heating is brought
up to temperature more rapidly.
This system must be programmed to start up
before you enter the vehicle.
Supplementary heating
On the 2-3 seats model, this is located under
t he seat on the driver's side with air diffusion
directed forwards.
On the 5 -9
seats model, it is
located at the rear. Depending
on the model, the air diffusion
is either direct from the rear
or comes from the rail located
under each of the two rows of
seats.
F

P
ress this control to activate/
deactivate the heating. The
LED comes on if the heating is
activated.
When rapid demisting and defrosting is
required, switch off the control.
Rear heating and/or air
conditioning
If your vehicle is fitted with an additional air
conditioning unit, located in the rear of the
vehicle: the distribution rail located in the
roof and the individual diffusion vents provide
a
per fect diffusion of cold air.
Ease of use and comfort