2018 MITSUBISHI OUTLANDER PHEV Owner's Manual (in English)

ScreenCauseSolution (Reference)lEV priority mode is not available because
the cruise control or the Adaptive Cruise
Control System (ACC) is operating.l EV priority mode is not available because
the EV priority mode is limited to protect
the Plug-in Hybrid EV System or the out-
side temperature is too low.l EV priority mode is cancelled because the
drive battery level is low.l EV priority mode is cancelled because the
vehicle speed of the cruise control or theAdaptive Cruise Control System (ACC) is
set.l EV priority mode is cancelled because the
protecting device of the Plug-in Hybrid
EV System is operated.
Indication lamp, warning lamp, and information screen display list
6-25OGGE18E1Instruments and controls6

ScreenCauseSolution (Reference)lYou have forgotten to turn off the lamps.l Refer to “Lamps (headlamps, fog lamps,
etc.) auto-cutout function” on page 6-52.l The washer fluid is running low.lReplenish the container with washer fluid.
Refer to “Washer fluid” on page 11-08.
Refer to “Refill capacities” on page
12-10.l There is a fault in the LED headlamps.lHave your vehicle inspected by a
MITSUBISHI MOTORS Authorized
Service Point.
Refer to “LED headlamp warning lamp” on page 6-53.l There is a fault in the keyless operation
system.l Refer to “Keyless operation system” on
page 4-06.
Indication lamp, warning lamp, and information screen display list
6-26OGGE18E1Instruments and controls6

ScreenCauseSolution (Reference)lThe keyless operation key is not detected.lInsert the keyless operation key into the
key slot.
Refer to “If the keyless operation key is not operating properly” on page 7-15.l You have forgotten to remove the keyless
operation key from the key slot.l Remove the keyless operation key from
the key slot.
Refer to “Keyless operation key remind-
er” on page 7-16.l There is a fault in the EPS.l Have the vehicle inspected by a
MITSUBISHI MOTORS Authorized
Service Point as soon as possible.
Refer to “Electric power steering system
(EPS)” on page 7-39.l The RBS (regenerative brake system) can-
not be used.l Have your vehicle inspected by a
MITSUBISHI MOTORS Authorized
Service Point.
Indication lamp, warning lamp, and information screen display list
6-27OGGE18E1Instruments and controls6

ScreenCauseSolution (Reference)lThere is a fault in the ABS.l Avoid sudden braking and high-speed
driving, stop the vehicle in a safe place, and take corrective measures. Refer to“ABS warning lamp/display” on page
7-37.l The tyre pressure in one of the tyres is
low.l Refer to “Tyre pressure monitoring sys-
tem warning lamp/display” on page 7-90.l There is a fault in the tyre pressure moni-
toring system.l Refer to “Tyre pressure monitoring sys-
tem warning lamp/display” on page
7-90.l One of the doors or the tailgate is not
completely closed.
The open door is displayed.l Close the door or tailgate.
Refer to “Door ajar warning display screen” on page 6-09.l The bonnet is open.lClose the bonnet.
Refer to “Bonnet” on page 11-04.
Indication lamp, warning lamp, and information screen display list
6-28OGGE18E1Instruments and controls6

ScreenCauseSolution (Reference)lThere is a fault in the electronic immobil-
izer (Anti-theft starting system).l Put the operation mode in OFF, and then
start the Plug-in Hybrid EV System again.If the warning is not cancelled, please
contact a MITSUBISHI MOTORS Au-
thorized Service Point.l The driver’s door is open when the opera-
tion mode is in any mode other than OFF.l Put the operation mode in OFF.
Refer to “Operation mode ON reminder
system” on page 7-14.l An attempt was made to lock all the doors
and the tailgate when the operation mode
is in any mode other than OFF.l Put the operation mode in OFF.
Refer to “Operation mode OFF reminder system” on page 7-13.l There is a fault in the electrical system.l Immediately stop the vehicle in a safe
place.
We recommend you to contact a MITSUBISHI MOTORS Authorized
Service Point.l The engine is overheated.lStop the vehicle in a safe place and take
corrective measures.
Refer to “Engine overheating” on page 9-04.l You put the operation mode in ON with-
out fastening your seat belt.l Fasten your seat belt properly. Refer to
“Seat belt reminder” on page 5-11.
Indication lamp, warning lamp, and information screen display list
6-29OGGE18E1Instruments and controls6

ScreenCauseSolution (Reference)lThere is a fault in the fuel system.l We recommend you to have it checked,
immediately.l The fuel is running low.lRefuel as soon as possible. Refer to
“Fuel
remaining warning display” on page 6-10.l You are driving with the parking brake
still applied.l Release the parking brake. Refer to
“Brake warning display” on page 6-51.l The brake fluid level in the reservoir has
fallen to a low level.
l There is a fault in the brake system.lImmediately stop the vehicle in a safe
place.
We recommend you to consult a MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Brake warning display” on page 6-51.l When the brake pedal has been repeatedly
depressed over a short period of time, the brake warning lamp may come on and thebrake warning buzzer may sound, and this
warning may be displayed.l If this warning display has disappeared
and the brake warning lamp goes out and the buzzer stops a few seconds after stop-
ping the brake operation, there is no ab-
normality.
Indication lamp, warning lamp, and information screen display list
6-30OGGE18E1Instruments and controls6

ScreenCauseSolution (Reference)lThere is a fault with the Electric parking
brake.l We recommend you to have it checked,
immediately.
Refer to “Electric parking brake” on page
7-03.l The parking brake cannot be applied tem-
porarily due to repeated operation of the
Electric parking brake switch within a short time.l Refer to “Electric parking brake” on page
7-03.l You try to release the Electric parking
brake switch without depressing the brake pedal.l Refer to “Electric parking brake” on page
7-03.l The Electric parking brake has been auto-
matically applied.l Refer to “Brake auto hold” on page 7-32.lThe brake auto hold is automatically can-
celled.l Refer to “Brake auto hold” on page 7-32.
Indication lamp, warning lamp, and information screen display list
6-31OGGE18E1Instruments and controls6

ScreenCauseSolution (Reference)lThe brake auto hold is not available.l Refer to “Brake auto hold” on page 7-32.lThe brake auto hold system does not turn
on because the driver’s seat belt is not fas-
tened.l Press the brake auto hold switch after fas-
tening the driver’s seat belt.
Refer to “Brake auto hold” on page 7-32.l The brake auto hold system does not turn
off because the brake pedal is not pressed.l Depress the brake pedal more firmly than
usual with the right foot. Then, press the
brake auto hold switch.
Refer to “Brake auto hold” on page 7-32.l There is a fault in the engine oil circula-
tion system.l Immediately stop the vehicle in a safe
place. We recommend you to have it checked.
Refer to “Oil pressure warning display” on page 6-51.l There is a fault in the Supplemental re-
straint system (SRS) airbag or the preten-
sioner system.l We recommend you to have it checked,
immediately.
Refer to “SRS warning lamp/display” on
page 5-36.
Indication lamp, warning lamp, and information screen display list
6-32OGGE18E1Instruments and controls6