2018 AUDI A7 Owners Manual

a co ,...,
N
" N ,...,
0 00 <.,;) ' significantly under-inflated tire causes the tire to
overheat and can lead to tire failure. Under-inf la­
tion also reduces fuel efficiency and tire tread
life, and may affect the vehicle's handling and
stopping ability.
Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the driver's re­
sponsibility to maintain correct tire pressure,
even if under-inflation has not reached the level
to trigger illumination of the TPMS low tire pres ­
sure telltale .
Your vehicle has also been equipped with a TPMS
malfunction indicator to indicate when the sys­
tem is not operating properly . The TPMS mal­
function indicator is combined with the low tire pressure telltale . When the system detects a
malfunction, the telltale will flash for approxi­
mately one minute and then remain continuously
illuminated. This sequence will continue upon
subsequent vehicle start-ups as long as the mal­
function exists.
When the malfunction indicator is illuminated,
the system may not be able to detect or signal
low tire pressure as intended. TPMS malfunctions
may occur for a variety of reasons, including the
installation of replacement or alternate tires or
wheels on the vehicle that prevent the TPMS
from functioning properly . Always che ck the
TPMS malfunction telltale after replacing one or
more tires or wheels on your vehicle to ensure
that the replacement or alternate tires and
wheels allow the TPMS to continue to function
properly.
Wheels
If the tire pressure monitoring system
indicator appears
Applies to: vehicles with Tire Pressure Monito ring System in­
dicator
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too low
or if there is a system malfunction.
Fig. 191 Ins trumen t cluster : indicator light w it h message
Using the ABS sensors, the tire pressure monitor­
ing system compares the tire tread circumfer­
ence and vibration characteristics of the individu­
al tires.
If the pressure changes in one or more
tires, th is is ind icated in the instrument cluster
display with an indicato r light
[I] and a message .
If only one tire is affected, the location of that
tire will be indicated.
The tire pressures must be stored in the Infotain­
ment system again each time the pressures
change (switching between partial and full load
pressure) or after changing or replacing a tire on
your
vehicle ~ page 224. The tire pressure moni­
toring system only monitors the tire pressure you
have stored. Refer to the tire pressure label for
the recommended tire pressure for your vehicle
~ page 215, fig . 190.
Tire tread circumference and vibration character­
istics can change and cause a tire pressure warn­
ing if :
- the tire pressure in one or more tires is too low
- the tire has structural damage
- the tire was replaced or the tire pressure was
changed and it was not stored
~ page 224
- the spare tire* is installed
223

Wheels
Indicator lights
It]-loss of pressure in at least one tire¢,&. .
Check the tires and replace or repair if necessary.
Check/correct the pressures of all four tires and
store the pressure again in the Infotainment sys­
tem
¢ page 224.
[m]) (Tire Pressure Monitoring System) Tire
pressure: System malfunction!.
If[m]J appears
after switching the ignition on or while driving
and the
RI] indicator light in the instrument clus­
ter blinks for approximately one minute and then
stays on, there is system malfunction. Try to
store the correct tire
pressures¢ page 224 . If
the indicator light does turn off or turns on again
after a short period of time, drive to an author­
ized Audi dealer or authorized Audi Service Facili­
ty immediately to have the malfunction correct­
ed.
A WARNING
- If the tire pressure indicator appears in the
display, reduce your speed immediately and
avoid any hard steering or braking maneu­
vers. Stop as soon as possible and check the
tires and their pressure .
- The driver is responsible for maintaining the
correct tire pressure. You must check the
tire pressure regularly.
- Under certain conditions (such as a sporty
driving style, winter conditions or unpaved
roads), the tire pressure monitoring system
indicator may be delayed.
(D Tips
- The tire pressure monitoring system can al­
so stop working when there is an ESC mal­
function.
- Using snow chains may result in a system
malfunction.
- The tire pressure monitoring system in your
Audi was calibrated with "Audi Original
Tires"
¢ page 212. Using these tires is rec­
ommended .
224
Storing tire pressures
Applies to: vehicles with Tire P ressure Monitoring System in­
dicator
If the tire pressure changes or a tire is replaced,
it must be confirmed in the Infotainment sys­
tem.
.,. Make sure before storing that the tire pressures
of all four tires meet the specified values and
are adapted to the load
¢page 215.
.,. Switch the ignition on .
.,. Select: the I CARI function button > (Car)* Sys­
tems
control button > Service & control > Tire
pressure monitor> Store tire pressure > Yes,
store now.
(D Tips
Do not store the tire pressures if snow chains
are installed.
Tire pressure monitoring
system
ill General notes
Each tire, including the spare (if provided),
should be checked monthly when cold and inflat­
ed to the inflation pressure recommended by the
vehicle manufacturer on the vehicle placard or
tire inflation pressure label. (If your vehicle has
tires of a different size than the size indicated on
the vehicle placard or tire inflation pressure la­
bel, you should determine the proper tire infla­
tion pressure for those tires).
As an added safety feature, your vehicle has been
equipped with a tire pressure monitoring system
(TPMS) that illuminates a low tire pressure tell­
tale when one or more of your tires is significant­
ly under-inflated. Accordingly, when the low tire
pressure telltale illuminates, you should stop and
check your tires as soon as possible, and inflate
them to the proper pressure. Driving on a signifi­
cantly under-inflated tire causes the tire to over­
heat and can lead to tire failure. Under-inflation
also reduces fuel efficiency and tire tread life,
and may affect the vehicle's handling and stop-
ping ability.
.,.

a co .... N
" N .... 0 00 \,;J ' Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the driver's re­
sponsibility to maintain correct tire pressure,
even if under-inflation has not reached the level
to trigger illumination of the TPMS low tire pres­
sure telltale .
Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the sys­
tem is not operating properly. The TPMS mal­
function indicator is combined with the low tire pressure telltale. When the system detects a
malfunction, the telltale will flash for approxi­
mately one minute and then remain continuously
illuminated. This sequence will continue upon
subsequent vehicle start-ups as long as the mal­
function exists.
When the malfunction indicator is illuminated,
the system may not be able to detect or signal
low tire pressure as intended. TPMS malfunctions
may occur for a variety of reasons, including the
installation of replacement or alternate tires or
wheels on the vehicle that prevent the TPMS
from functioning properly . Always check the
TPMS malfunction telltale after replacing one or
more tires or wheels on your vehicle to ensure
that the replacement or alternate tires and
wheels allow the TPMS to continue to function
properly.
Description
Applies to: vehicles with tire pressure monitor ing system
The tire pressure monitoring system monitors
the pressure in the four tires when driving.
T he system uses sensors that measure the tem ­
perature and pressure in the tires . The data is
sent from these sensors to the control module by radio frequency.
T he Tire Pressure Monitoring System shows the
current pressures and temperatures of the tires
in the Infotainment system
¢page 226. It also
compares the current tire pressures with the
stored tire pressures and gives a warning in the
driver information system if the tire pressure is
different from what is
stored ¢ page 226 .
Wheels
The system does not detect if the stored tire
pressures match the recommended tire pres­
sures. You must store the tire pressures again
¢ page 226:
- every time the tire pressures change, for exam­
ple when the load in the vehicle changes,
- after replacing a tire, or
- if wheels with new wheel sensors are used.
_& WARNING
- The tire pressure monitoring system assists
the driver in monitoring tire pressures. The
driver is responsible for having the tires in­
flated to the correct pressure.
- Do not change the tire pressure when the
temperature of the tire is extremely high.
This could result in serious damage to the
tire and even cause the tire to burst, in­
creasing the risk of an accident.
- A tire with low pressure flexes more. This heats the tire up too much. This could cause
the tread to separate and even cause the
tire to burst, increasing the risk of an acci­
dent.
- The tire pressure monitoring system does not warn about damage or defects in the
tire construction that could cause the tire to
burst, for example. Inspect your tires regu­
larly.
(D Tips
- If tires are replaced, the sensors/valves do
not need to be removed or replaced . Just re­
placed the valve stem and, if necessary, the
valve and the wheel electronics. If you have questions, see an authorized Audi dealer or
authorized Audi Service Facility.
- An incorrect display or a malfunction in the
tire pressure monitoring system can occur
after using the tire mobility kit. Have the
sensors replaced by an authorized Audi
dealer or authori zed Audi Service Facility.
- For an explanation on conformity with the
FCC regulations in the United States and the
Industry Canada regulations, see
¢ page 258.
225

Wheels
Displaying tire pressures/temperatures
Applies to: vehicles with tire pressure monitoring system
Requirement: the ign ition must be switched on.
.,. Select : the ICARI function button > Car systems
> Service & control> Tire pressure monitor>
Display tire pressure .
The current tire pressures are shown in green and
yellow numbers in the Infotainment system:
- Green: the current tire pressure and the speci­
fied tire pressure are approximately the same.
- Yellow: the current tire pressure is too low
compared to the specified tire pressure.
The specified tire pressure is the last tire pres­
sure that was stored
9 page 226 .
Note that the tire pressure also depends on the
temperature of the tire. The tire pressure in­
creases as the engine becomes warmer while
driving.
A WARNING
Read and follow the important information
and notes
q page 225.
@ Tips
The tire pressure or temperature are not dis ­
played in adaptation mode. Dashes --.-- are
shown in place of the pressure and tempera ­
ture.
CD Tire pressure loss
App lies to: veh icles with tire pressure mon itoring system
Fig. 192 Display : in dic ato r light with a me ssage
226
-
If the (D] indicator light turns on, the pressure in
at least one tire is too low or new sensors were
not adapted:
RE indicator lights turns on after turning the
ignition on
The tire pressure is too low compared to the
specified pressure.
.,. Check and store the tire pressure(s) the next
time it is possible
9 page 226.
RE indicator light turns on while driving
Wheels with new sensors were not adapted or
the tire pressure has reached a critical level com­
pared to the specified pressure.
.,. Avoid unnecessary steering and braking maneu-
vers.
.,. Adapt your driving sty le to the situation.
.,. Stop as soon as possible and check the tire(s).
.,. If it is possible to continue driving, see an au-
thorized Audi dealer or authorized Audi Service
Facility immediately and have your tire(s) re­
paired or replaced.
A WARNING
Read and follow the important information
and notes ¢
page 225.
Storing new tire pressures
Applies to: vehicles with tire pressure mon itoring system
Correctly stored tire pressure specifications are
necessary for reliable tire pressure monitoring.
.,. Check the tire pressures in all wheels .
-
.,. Correct the tire pressure if necessary. Refer to
the tire pressure Label for the recommended
tire pressure for your vehicle
c> page 215,
fig . 190 .
Only correct the pressure in tires
whose temperature is approximately the same
as the ambient temperature. If the tempera­
ture of the tire is higher than the ambient air
temperature, the tire pressure must be in­
creased approximately 3 PSI (0,2 bar) above
the value on the sticker .
.,. Switch the ignition on .
.,. Select: !CAR ! function button > Car systems>
Tire pressure monitoring
> Store tire pressure . ..,.

a co .... N
" N .... 0 00 \.J ' After storing, the tire pressure monitoring sys­
tem measures the current tire pressures and stores them as the new specified pressures.
~ If the changed tire pressures are not displayed
in the Infotainment system, drive the vehicle
for approximately 10 minutes so that the sen­
sor signal from the wheels is received again.
During this adaptation phase, --.·· is displayed
for the pressure and temperature and the tire
pressure monitoring system is only partially
available. It only provides a warning if one or
more tir e pressures is below the minimum per­
mitted specified pressure. If this is the case, the
IE indicator light appears with a message.
& WARNING
Read and follow the important information
and notes
¢p age 225.
Malfunctions
Applies to: vehicles with tire pressure monitoring syste m
-
If the Tire Pressure Monitoring System is not
avai lable, the
mm indicator light appears in the
driver information system. The
IE indicator light
also blinks for approximately one minutes each
time the ignition is switched on . The tire pressure
monitoring system cannot be selected in the In­
fotainment system. The fol lowing are examples
of situat ions that could cause a malfunction:
-If the message appears at the end of the adap­
tation phase, the system cannot detect the
wheels installed on the vehicle. This may resu lt
from one or more wheels being installed with­
out wheel sensors or with incompatible wheel
sensors.
-A wheel sensor or another component has
failed.
-Using snow cha ins can affect the function of
the system because of the shield ing effect of
the chains .
-The tire pressure monitoring system is not
available due to a malfunction.
-T ransmitters with the same frequency, such as
headphones or remote-control led dev ices, may
cause a temporary system malfunction due to
the strong electromagnetic field.
Wheels
T he m;i indicator light turns off once the Tire
Pressure Monitoring System is available again. If
you cannot correct the ma lfunction and the
m;i
indicator light stays on, drive immediately to an
authorized Audi dealer or authorized Audi Service
Facility to have the malfunction repaired.
227

Care and cleaning
Care and cleaning
General information
Regular, proper care helps to maintain your vehi­
cle's value. It can also be a requirement when
submitting warranty claims for corrosion damage
and paint defects on the body.
The necessary care products can be obtained
from an authorized Audi dea ler or authorized
Audi Service Facility. Read and follow the instruc ­
tions for use on the packaging.
A WARNING
-Using cleaning and care products incorrectly
can be dangerous to your health.
- Always store clean ing and care products out
of reach of children to reduce the r isk of poi­
sonin g.
@ For the sake of the environment
- Preferab ly purchase environmenta lly-friend­
l y cleaning products.
- Do not dispose of leftover cleaning and care
products with household trash.
Car washes
The longer that deposits remain on the vehicle,
the more the surface may be damaged. High
temperatures such as those caused by sunlight increase the damaging effect .
Before washing, rinse
off heavy deposits with
p lenty of water.
Stubborn deposits such as bird droppings or tree
sap are best removed with plenty of water and a
microfiber cloth.
A lso, wash the underside of yo ur vehicle once
road sa lt stops being used for the season.
Pressure washers
When washing your veh icle w ith a pressure wash­
er, always follow the operating instructions pro­
vided with the press ure washer. This is espec ially
impor tant in r egard to the pressure and spraying
distance. Do not aim the spray directly at the
sea ls on the side windows, doors, lids or the sun-
228
roof* or at tires, rubber hoses, insulating materi­
a l, sensors* or camera lenses* . Keep a distance of
at least 16 in (40 cm) .
Do not remove snow and ice with a pressure
washe r.
Never use cone nozzles o r high pressu re nozzles.
The water temperature must not be above 140 °F
(60 °().
Automatic car washes
Spray off the vehicle before washing .
Make sur e that the windows and roof* are closed
and the windshie ld wipers are
off. Follow instruc­
tions from the car wash operator, especially if
there are accessories attached to your vehicle .
If possible, use car washes that do not have
brushes.
Applies to : RS models: only use car washes where
the vehicl e remai ns stationary and the washing
equipment moves around the vehicl e when wash­
ing and drying. Car washes that move the vehicle
through the car wash using a chain are not rec­
ommended.
Washing by hand
Clean the vehicl e starting from the top and work­
ing down using a soft sponge or cleaning brush.
Use solvent -free cleaning products.
Washing vehicles with matte finish paint by
hand
To avoid damaging the paint when washing, first
remove dust and large particles from your vehi ­
cle. Insects, grease spots and fingerprints are
best removed with a special cleaner for matte
finish paint.
Apply t he product using a microfiber cloth. To
avoid damaging the paint surface, do not use too
much pressure.
Rinse t he ve hicle thoroughly with water. Then
clean using a neutra l shampoo and a so ft micro­
fiber clot h.
R inse the vehicl e thoroughly again and let it air
dry. Remove any water residue using a chamois.
..,..

a co .... N
" N .... 0 00 \.J ' & WARNING
-Only wash the vehicle when the ignition is
off and follow the instructions from the ca r
was h operator to reduce the risk of acci­
dents.
-T o red uce the risk of cuts, protect yourself
from sha rp metal components when wash­
ing the underbody or the inside of t he wheel
hous ings .
-After wash ing the vehicle, the brak ing effect
may be delayed due to mo isture on the
brake rotors or ice in the w inter . This in­
c reases the risk of an acc ide nt. The bra kes
mus t be d rie d first w ith a few careful brake
app lic at ions.
@ Note
-If yo u wash t he veh icle in an automatic car
wash, yo u m ust retract the rear spoi ler if
necessa ry, and fold the exte rior m irrors i n
to re du ce the risk of damage. Powe r fo ldi ng
ex ter io r m irr ors* m ust only be fo lde d in a nd
o ut u sing t he power folding fu nction .
-
Care and cleaning
-To re duce the risk of pa int damage, do not
was h the vehicle in direct su nlight .
-To re duce the risk of d amage to the s urface,
do not use insect removing sponges, kitche n
sponges or s imilar items .
-Mat te finish painted veh icle components :
-To reduce the risk of damage to t he sur-
face, do not use po lish ing agents o r hard
wax.
-Neve r use protective wax. It can destroy
the matte finish effect .
-Do not place any st ickers or magnetic
s igns on vehicle parts painted w ith matte
finish paint . The paint cou ld be damaged
when the stickers or magne ts are re ­
m oved.
@ For the sake of the environment
Only wash the veh icle in facili ties s pec ia lly de­
s igned for tha t pur pose . This will reduce the
r isk of di rty wate r cont ami nated with o il from
ente rin g t he sewe r sys tem.
Cleaning and care information
When cleani ng and ca ring for in dividua l vehicle
componen ts, re fer to the follow ing tables. The
i nf ormation contained there is s imp ly recom ­
mendations. Fo r qu est ions or for components t
h at are not liste d, co n su lt an au tho riz e d Au di
dealer or au thor ized A udi Se rvice Fa cility. Also
f o llow the information fo und
in ¢ .&. .
Exterior cleaning
Component Situation Solution
Windshield wiper
Deposits Soft cloth with g
lass cleaner, ¢ page 46
blades
Headlights/
Deposi ts So
ft spo nge wi th a m ild soap sol utiona )
Tail lights
Sensors /
Deposits Sensors: soft cloth wit h solvent-free cleaning solut io n
camera lenses Camera le nses: soft cloth w ith a lcoho l- free cleaning so lu -
tion
Snow/ice H
and br ush/solvent-free de -icing spray
Wheels Road salt Water
Bra ke dust Acid-f
ree s pecial clea ning so lution
E xhaust tail pipes Road salt Water, clean ing so lution su itab le for s tainless stee l, if nee-
ess ary
229

Care and cl eaning
Component Situation Solution
De cora tiv e p arts/
Deposits Mild soap so lution al, a cleaning solution suitable for stain-
t rim less stee l, if necessary
Paint Paint damage Refer to the paint numbe r on the vehicle data label, repair
with touch up pa int
9 page 253
Spilled fuel Rinse with water immediately
Surface rust Rust remover, then protect
with hard wax; for questions,
consult an authorized Audi dealer or authorized Audi Serv-
ice Facility .
Corros ion Have it removed by an authorized Aud i dea ler or author-
i zed Audi Service Fac il ity.
Water no longer Protect with hard wax (at least twice per year)
beads on the surface
of clean paint
No shine even though Treat with
suitable polish; then apply paint protectant if
paint has been pro- the polish that was used does not contain any protectant
tected/paint looks
poor
Deposits such as in- Dampen w ith wate r immediately and remove wit h a m icro -
sects, bird dropp ings, fiber cloth
tree sap and road salt
Grease -based con- Remove immediately with a m ild soap solution
a) and a
taminants such as soft cloth
cosmetics or sunb lock
Car bon parts Deposits clean the same way as painted parts 9page 228
al Mild soap so lut ion : m axim um tw o tab lespoo ns o f neu tra l soap i n 1 qua rt (1 lite r) of water
Int erior cl ea ni ng
Component Situation Solution
Wind ows
Deposits Glass cleaner, then wipe dry
Deco rat ive p art s/ Deposits Mild
soap solution a)
t rim
Pla stic parts
Deposits Damp cloth
Heavier deposits Mild soap solution al, detergent-free plastic cleaning solu -
tion, if necessary
Di spla ys Deposits Soft cloth with LCD cleaner
C ontrol s Deposits Soft brush, then a soft cloth with a mild soap solutiona>
Safet y belts Deposits Mi
ld soap so lution al, allow to dry befo re letting them re -
tract
230