2017 INFINITI QX30 Owners Manual

If you use oxygenate-blend gasoline, please
take the following precautions as the usage of
such fuels may cause vehicle performance prob-
lems and/or fuel system damage.
•The fuel should be unleaded and have an
octane rating no lower than that recom-
mended for unleaded gasoline.
•If an oxygenate-blend, other than a methanol
blend, is used, it should contain no more than
10% oxygenate. (MTBE may, however, be
added up to 15%.)
•E-15 fuel contains more than 10% oxygenate.
E-15 fuel will adversely affect the emission
control devices and systems of the vehicle
and should not be used. Damage caused by
such fuel is not covered by the INFINITI New
Vehicle Limited Warranty.
•If a methanol blend is used, it should contain no
more than 5% methanol (methyl alcohol, wood
alcohol). It should also contain a suitable
amount of appropriate cosolvents and corrosion
inhibitors. If not properly formulated with appro-
priate cosolvents and corrosion inhibitors, such
methanol blends may cause fuel system damage
and/or vehicle performance problems.
At this time, sufficient data is not available to
ensure that all methanol blends are suitable
for use in INFINITI vehicles.If any driveability problems such as engine
stalling and difficult hot-starting are experi-
enced after using oxygenate-blend fuels, imme-
diately change to a nonoxygenate fuel or a fuel
with a low blend of MTBE.
Take care not to spill gasoline during refueling.
Gasoline containing oxygenates can cause paint
damage.
E-15 fuel
E-15 fuel is a mixture of approximately 15% fuel
ethanol and 85% unleaded gasoline. E-15 can
only be used in vehicles designed to run on E-15
fuel. Do not use E-15 in your vehicle. U.S.
government regulations require fuel ethanol
dispensing pumps to be identified with small,
square, orange and black label with the com-
mon abbreviation or the appropriate percentage
for that region.
E-85 fuel
E-85 fuel is a mixture of approximately 85% fuel
ethanol and 15% unleaded gasoline. E-85 can
only be used in a Flexible Fuel Vehicle (FFV). Do
not use E-85 fuel in your vehicle. U.S. govern-
ment regulations require fuel ethanol dispens-
ing pumps to be identified by a small, square,
orange and black label with the common abbre-
viation or the appropriate percentage for that
region.
Fuel containing MMT
MMT, or methylcyclopentadienyl manganese tri-
carbonyl, is an octane boosting additive.
INFINITI does not recommend the use of fuel
containing MMT. Such fuel may adversely affect
vehicle performance, including the emissions
control system. Note that while some fuel
pumps label MMT content, not all do, so you
may have to consult your gasoline retailer for
more details.
Aftermarket fuel additives
INFINITI does not recommend the use of any
aftermarket fuel additives (Example: fuel injec-
tor cleaner, octane booster, intake valve de-
posit removers, etc.) which are sold commer-
cially. Many of these additives intended for
gum, varnish or deposit removal may contain
active solvent or similar ingredients that can be
harmful to the fuel system and engine.
Octane rating tips
Using unleaded gasoline with an octane rating
lower than recommended above can cause per-
sistent, heavy spark knock. (Spark knock is a
metallic rapping noise.) If severe, this can lead
to engine damage. If you detect a persistent
heavy spark knock even when using gasoline of
the stated octane rating, or if you hear steady
spark knock while holding a steady speed on
10-4Technical information

level roads, it is recommended you have an
INFINITI retailer correct the condition. Failure to
correct the condition is misuse of the vehicle, for
which INFINITI is not responsible.
Incorrect ignition timing will result in knocking,
after-run and/or overheating. This in turn may
cause excessive fuel consumption or damage to
the engine. If any of the above symptoms are
encountered, have your vehicle checked. It is
recommended you visit an INFINITI retailer.
However, now and then you may notice light
spark knock for a short time while accelerating
or driving up hills. This is no cause for concern,
because you get the greatest fuel benefit when
there is light spark knock for a short time under
heavy engine load.
1API certification mark
2API service symbol
ENGINE OIL AND OIL FILTER
RECOMMENDATIONS
Selecting the correct oil
It is essential to choose the correct grade,
quality, and viscosity engine oil to ensure sat-
isfactory engine life and performance. For addi-
tional information, refer toRecommended
fluids/lubricants and capacitiesearlier in this
section. INFINITI recommends the use of an
energy conserving oil in order to improve fuel
economy.
Select only engine oils that meet the American
Petroleum Institute (API) certification or Interna-
tional Lubricant Standardization and ApprovalCommittee (ILSAC) certification and SAE viscos-
ity standard. These oils have the API certifica-
tion mark on the front of the container. Oils
which do not have the specified quality label
should not be used as they could cause engine
damage.
Oil additives
INFINITI does not recommend the use of oil
additives. The use of an oil additive is not
necessary when the proper oil type is used and
maintenance intervals are followed.
Oil which may contain foreign matter or has
been previously used should not be used.
Oil viscosity
The engine oil viscosity or thickness changes
with temperature. Because of this, it is impor-
tant that the engine oil viscosity be selected
based on the temperatures at which the vehicle
will be operated before the next oil change.
Choosing an oil viscosity other than that recom-
mended could cause serious engine damage.
Selecting the correct oil filter
Your new vehicle is equipped with a high—
quality genuine INFINITI oil filter. When replac-
ing, it is recommended you use the genuine oil
filter or its equivalent for the reason described
in “Change intervals”.
NTI326
Technical information10-5

Change intervals
The oil and oil filter change intervals for your
engine are based on the use of the specified
quality oils and filters. Using engine oil and
filters that are not of the specified quality, or
exceeding recommended oil and filter change
intervals could reduce engine life. Damage to
engines caused by improper maintenance or
use of incorrect oil and filter quality and/or
viscosity is not covered by the new INFINITI New
Vehicle Limited Warranty.
Your engine was filled with a high quality
engine oil when it was built. You do not have to
change the oil before the first recommended
change interval. Oil and filter change intervals
depend upon how you use your vehicle.
Operation under the following conditions may
require more frequent oil and filter changes:
•Repeated short distance driving at cold
outside temperatures
•Driving in dusty conditions
•Extensive idling
•Stop and go “rush hour” traffic
Refer to the “INFINITI Service and Maintenance
Guide” for the maintenance schedule.
AIR CONDITIONER SYSTEM
REFRIGERANT AND OIL
RECOMMENDATIONS
The air conditioner system of your vehicle must
be charged with the refrigerant HFC-134a and
the lubricant INFINITI A/C System Oil Type S or
the exact equivalents.
CAUTION
The use of any other refrigerant or oil may
cause severe damage to the air conditioning
system and will require the replacement of all
air conditioner system components.
The refrigerant HFC-134a in your vehicle will not
harm the Earth’s ozone layer. However, it may
contribute in a small part to the global warming
effect.
Certain government regulations require the re-
covery and recycling of any refrigerant during
automotive air conditioner system service. An
INFINITI retailer has the trained technicians and
equipment needed to recover and recycle your
air conditioner system refrigerant.
It is recommended that you visit an INFINITI
retailer when servicing your air conditioner sys-
tem.
10-6Technical information

Model 2.0L Gasoline
Type Gasoline, 4-cycle
Cylinder arrangement 4-cylinder in-line
Bore x Stroke in (mm) 3.268 x 3.622
(83.0 x 92.0)
Displacement cu in (cm
3) 121.55 (1,991)
Idling speed rpm
DCT in N position 700
Ignition timing (BTDC) degrees
DCT in N position -10°CA to +35°CA BTDC at 700rpm
Spark plug Standard Platinum tipped
Spark plug gap in (mm) 0.028 (0.7)
Camshaft operation Timing chain
This spark ignition system complies with the Canadian standard ICES-002.
ENGINE SPECIFICATIONS
Technical information10-7

GT and Sport models:
Item Offset in (mm) Size
Road wheel 1.50 (38) 6.5J x 17
1.81 (46) 7.0J x 18
1.71 (43.5) 8.0J x 19
Tire size 215/60 R17 96V
235/50 R18 97V*
235/50 R18 97H* **
235/45 R19 95V*
* : Use of snow chains NOT permitted.
**: US only.
All Road models:
Item Offset in (mm) Size
Road wheel 1.61 (41) 6.5J x 17
(steel)
1.61 (41) 7.0J x 18
(alloy)
Tire size 215/60 R17 96V
235/50 R18 97V*
235/50 R18 97H* **
* : Use of snow chains NOT permitted.
**: US only.
WHEELS AND TIRES
10-8Technical information

Dimension Model in (mm)
Overall length 174.2 (4425)
Overall width (incl. mirrors) 82.0 (2083)
Overall height GT without roof rails 58.9 (1495)
GT with roof rails 59.5 (1510)
Sport without roof rails 58.1 (1475)
Sport with roof rails 58.7 (1490)
Allroad without roof rails 58.7 (1515)
Allroad with roof rails 61.2 (1530)
Front track GT 17” wheels 61.9 (1572)
GT 18” wheels 61.3 (1556)
GT 19” wheels 61.5 (1561)
Sport 17” wheels 62 (1574)
Sport 19” wheels 61.5 (1563)
Allroad 17” wheels 61.7 (1566)
Allroad 18” wheels 61.5 (1561)
Rear track GT 17” wheels 61.9 (1573)
GT 18” wheels 61.2 (1555)
GT 19” wheels 61.7 (1566)
Sport 17” wheels 62.2 (1580)
Sport 19” wheels 61.7 (1567)
Allroad 17” wheels 62.0 (1574)
Allroad 18” wheels 61.7 (1566)
Wheelbase 106.3 (2700)
DIMENSIONS
Technical information10-9

When planning to drive your INFINITI VEHICLE in
another country, you should first find out if the
fuel available is suitable for your vehicle’s
engine.
Using fuel with an octane rating that is too low
may cause engine damage. All gasoline ve-
hicles must be operated with unleaded gaso-
line. Therefore, avoid taking your vehicle to
areas where appropriate fuel is not available.
When transferring the registration of your ve-
hicle to another country, state, province or dis-
trict,it may be necessary to modify the vehicle
to meet local laws and regulations.
The laws and regulations for motor vehicle
emission control and safety standards vary
according to the country, state, province or
district; therefore, the vehicle specification may
differ.
When any vehicles are to be taken into another
country, state, province or district, its modifica-
tion, transportation, registration, and any other
expenses which may result, are the responsibil-
ity of the user. INFINITI is not responsible for any
inconveniences that may result.It is prohibited to cover, paint, weld, cut, drill,
alter or remove the Vehicle Identification Num-
ber (VIN).
VEHICLE IDENTIFICATION NUMBER
(VIN) PLATE
The vehicle identification number plate is at-
tached as shown. This number is the identifica-
tion for your vehicle and is used in the vehicle
registration.
JVT0352XZ
WHEN TRAVELING OR REGISTERING IN
ANOTHER COUNTRYVEHICLE IDENTIFICATION
10-10Technical information

VEHICLE IDENTIFICATION NUMBER
(CHASSIS NUMBER)
The vehicle identification number is stamped as
shown.
ENGINE SERIAL NUMBER
The number is stamped on the engine as
shown.
F.M.V.S.S./C.M.V.S.S. CERTIFICATION
LABEL
The Federal/Canadian Motor Vehicle Safety
Standards (F.M.V.S.S./C.M.V.S.S.) certification
label is affixed as shown. This label contains
valuable vehicle information, such as: GVWR,
GAWR, month and year of manufacture, VIN, etc.
Review it carefully.
EMISSION CONTROL INFORMATION
LABEL
The emission control information label is at-
tached as shown.
NTI314NDI16212.0L gasoline enginesNTI324
Technical information10-11