2017 INFINITI QX30 Owners Manual

Deactivating the temporary manual drive program:
Pull and hold the right steering wheel gearshift
paddle until the automatic transmission shifts into
the last active automatic drive program E or S.
When manual drive program M is deactivated,
the automatic transmission in automatic drive
program E or S may shift from the current gear
into a higher or lower gear. This is dependent
on the position of the accelerator pedal, speed
and load.Problems with the transmission
:
Problem Possible causes/consequences and solutions
The transmission has problems shift-
ing gearThe transmission is losing oil.
Have the transmission checked immediately. It is recommended you
visit an INFINITI retailer for this service.
The acceleration ability is deteriorat-
ing The transmission no longer shifts
into all of the gears Reverse gear can
no longer be engagedThe transmission is in emergency mode.
•Stop.•Shift the transmission to position P (Park).•Switch off the engine.•Wait at least ten seconds before restarting the engine.•Shift the transmission to position D (Drive).•Have the transmission checked immediately. It is recommended
you visit an INFINITI retailer for this service.
5-24Starting and driving

WARNING
•Be sure the parking brake is fully released
before driving. Failure to do so can cause
brake failure and lead to an accident.
•Do not release the parking brake from out-
side the vehicle.
•Do not use the shift lever in place of the
parking brake. When parking, be sure the
parking brake is fully engaged.
•To help avoid risk of injury or death through
unintended operation of the vehicle and/or
its systems, do not leave children, people
who require the assistance of others, or
pets unattended in your vehicle. Addition-
ally, the temperature inside a closed vehicle
on a warm day can quickly become high
enough to cause a significant risk of injury
or death to people and pets.The function of the electric parking brake is
dependent on the on-board voltage. If the on-
board voltage is low or if there is a malfunction
in the system, it may not be possible to apply
the released parking brake. If this is the case:
•Only park the vehicle on level ground and
secure it to prevent it from rolling away.
•Shift the automatic transmission to position
P (Park).
•It is recommended you contact an INFINITI
retailer.
It may not be possible to release an applied
parking brake if the on-board voltage is low or
if there is a malfunction in the system. It is
recommended you contact an INFINITI retailer.
The electric parking brake carries out a function
check at regular intervals when the engine is
switched off. Noises that occur are normal.APPLYING/RELEASING MANUALLY
The electric parking brake can be applied or
released by operating the parking brake handle
1.
To apply:Push handle
1.
When the electric parking brake is applied, the
red
indicator lamp lights up in the
combination meter.
The electric parking brake can also be applied
when the ignition switch is in the OFF position
or the key is removed.
To release:With the ignition switch in the ON
position, pull handle
1.
NPA1485
PARKING BRAKE
Starting and driving5-25

Before driving, check that the brake warning
lightgoes out. For additional informa-
tion, seeWarning lights, indicator lights and
audible remindersin the2. Instruments and
controlssection.
The electric parking brake can only be released
when the ignition switch is in the ON position.
APPLYING AUTOMATICALLY (VEHICLES
WITH AUTOMATIC TRANSMISSION)
The electric parking brake is automatically ap-
plied when:
•Intelligent cruise control (if equipped) brings
the vehicle to a standstill.
or
•Intelligent Parking Assist (if equipped) is
keeping the vehicle stationary.
The red
indicator lamp lights up in the
combination meter.
The electric parking brake is not automatically
applied if the engine is switched off by the Idle
Stop/Start function.
RELEASING AUTOMATICALLY
The electric parking brake can only be released
automatically in vehicles with automatic trans-
mission.
The electric parking brake of your vehicle is
released automatically when all of the following
conditions are fulfilled:
•The engine is running.
•The transmission is in position D (Drive) or R
(Reverse).
•The seat belt is fastened.
•You depress the accelerator pedal.
If the transmission is in position R, the lift gate
must be closed.
If your seat belt is not fastened, the following
conditions must be fulfilled to automatically
release the electric parking brake:
•The driver’s door is closed
•You have shifted out of transmission posi-
tion P (Park) or you have previously driven
faster than 2 MPH (3 km/h).
Ensure that you do not depress the accelerator
pedal unintentionally. Otherwise, the parking
brake will be released and the vehicle will start
to move.
EMERGENCY BRAKING
The vehicle can also be braked during an emer-
gency by using the electric parking brake.
While driving, push handle
1of the electric
parking brake. The vehicle is braked as long as
you keep handle
1of the electric parking
brake pressed. The longer the electric parking
brake handle
1is depressed, the greater the
braking force.
During braking:
•A warning tone sounds.
•The [Please Release Parking Brake] message
appears.
•The redindicator lamp in the combi-
nation meter flashes.
When the vehicle has been braked to a stand-
still, the electric parking brake is applied.
5-26Starting and driving

The Idle Stop/Start function switches the en-
gine off automatically if the vehicle is stopped
under certain conditions.
When pulling away again, the engine starts
automatically. The Idle Stop/Start function
thereby helps you to reduce the fuel consump-
tion and emissions of your vehicle.
WARNING
If the engine is switched off automatically and
you exit the vehicle, the engine is restarted
automatically. The vehicle may begin moving
There is a risk of accident and injury.
If you wish to exit the vehicle, always turn off
the ignition and secure the vehicle against roll-
ing away.If the
Idle Stop/Start symbol is shown in
green in the vehicle information display, the
Idle Stop/Start function switches the engine off
automatically once the vehicle stops moving.
The Idle Stop/Start function is automatically
activated each time you start the engine with
the ignition key.
If the Idle Stop/Start function has been manu-
ally deactivated (seeDeactivating/activating
the Idle Stop/Start functionlater in this sec-
tion) or a malfunction has caused the system to
be deactivated, the
Idle Stop/Start sym-
bol is not displayed.
AUTOMATIC ENGINE SWITCH-OFF
The Idle Stop/Start function is operational and
theIdle Stop/Start symbol is displayed
in green in the vehicle information display, if:
•The indicator lamp in the ECO button is lit
green.
•The outside temperature is within the range
that is suitable for the system.
•The engine is at normal operating tempera-
ture.
•The set temperature for the vehicle interior
has been reached.
•The battery is sufficiently charged.
•The system detects that the windshield is
not misted up when the air-conditioning sys-
tem is switched on.
•The hood is closed.
•The driver’s door is closed and the driver’s
seat belt is fastened.
If the conditions for automatic engine switch-off
are not all fulfilled, the
Idle Stop/Start
symbol is shown in yellow.
All of the vehicle’s systems remain active when
the engine is switched off automatically.
NSD620Idle Stop/Start symbol
IDLE STOP/START SYSTEM (IF EQUIPPED)
Starting and driving5-27

The engine can be switched off automatically a
maximum of four times (initial stop, then three
subsequent stops) in succession. The
Idle Stop/Start symbol is shown in yellow in the
vehicle information display after the engine has
been started automatically for the fourth time.
When the
Idle Stop/Start symbol is
shown in green in the vehicle information dis-
play, automatic engine switch-off is again pos-
sible.
NOTE
If the hood is opened while the engine is running
and the Idle Stop/Start function is operational,
the engine will switch off automatically.
If the vehicle is brought to a standstill in D or N,
the Idle Stop/Start function switches off the
engine automatically.
AUTOMATIC ENGINE START
The engine is started automatically if:
•You switch off the Idle Stop/Start function
by pressing the ECO button.
•You engage Reverse R or Drive D.
•You unfasten your seat belt or open the
driver’s door.
•The vehicle starts to roll.
•The brake system requires this.
•The temperature in the vehicle interior devi-
ates from the set range.
•The system detects moisture on the wind-
shield when the air-conditioning system is
switched on.
•The battery’s charge status is too low.
The engine is started automatically if you:
•Release the brake pedal in transmission
position D (Drive) or N (Neutral).
•Depress the accelerator pedal.
•Move the transmission out of position P
(Park).
Shifting the transmission to position P (Park)
does not start the engine.
If you shift the transmission from R (Reverse) to
D (Drive), the Idle Stop/Start function is avail-
able again once the
Idle Stop/Start
symbol reappears in green in the vehicle infor-
mation display.
DEACTIVATING/ACTIVATING THE IDLE
STOP/START FUNCTION
•To deactivate:press ECO button1. Indica-
tor lamp
2and theIdle Stop/Start
symbol in the vehicle information display
turn off.
•To activate:press ECO button1. Indicator
lamp
2lights up. If all conditions for auto-
matic engine switch-off (seeAutomatic engine
switch-offearlier in this section) are fulfilled,
the
Idle Stop/Start symbol is shown in
green in the vehicle information display.
If not all conditions for automatic engine
switch-off are met, theIdle Stop/Start
symbol is lit yellow in the vehicle information
display. If this is the case, the Idle Stop/Start
function is not active.
NIC2633
5-28Starting and driving

If indicator lamp2on ECO button1is off, the
Idle Stop/Start function has been deactivated
manually or as the result of a malfunction. The
engine will then not be switched off automati-
cally when the vehicle stops.WARNING
Failure to follow the warnings and instructions
for proper use of the LDW system could result
in serious personal injury or death. The LDW
system will not steer the vehicle or prevent
loss of control. It is the driver’s responsibility
to stay alert, drive safely, keep the vehicle in
the traveling lane, and be in control of the
vehicle at all times.
The LDW system warns the driver with a warn-
ing light and intermittent steering vibration that
the vehicle is beginning to leave the traveling
lane.The LDW system uses a camera
1installed
behind the windshield to monitor the lane
markers of your traveling lane.
NSD644
LANE DEPARTURE WARNING (LDW)
SYSTEM (IF EQUIPPED)
Starting and driving5-29

LDW SYSTEM OPERATION
1Steering wheel mounted controls
2Vehicle information display
ADisplay area
BMenu barThe LDW system operates at speeds of approxi-
mately 40 MPH (60 km/h) and above, when the
lane markings are clear.
If the system detects that the vehicle’s front
wheel has passed over the lane marking, a
warning will be provided. It will warn you by
means of intermittent vibration through the
steering wheel for up to 1.5 seconds and a
visual alert.
NOTE
The LDW system is designed not to warn when
you operate the lane change signal and change
traveling lanes in the direction of the signal.
No warning vibration occurs if you activate the
turn signals. In this event, the warnings are sup-
pressed for a certain period of time.
NSD626
5-30Starting and driving

HOW TO ENABLE/DISABLE THE LDW
SYSTEM
1. Press theorbutton on the
steering wheel
1to select the [DriveAssist]
menu on the Menu bar
B.
2. Press the
orbutton to select
[Lane Departure Warning].
3. Press thebutton on the steering wheel
1. The current selection is displayed.
4. Press theto confirm.
5. Press the
orbutton to set [Off],
[Standard] or [Adaptive].
6. Press thebutton to save the setting.
When the LDW is activated, the vehicle
information display shows the lane mark-ings as bright lines in the assistance graphic
in the display area
A
When [Standard] is selected, no warning vibra-
tion occurs if:
•You have switched on the turn signals. In
this event, the warnings are suppressed for a
certain period of time.
•A driving safety system intervenes, such as
ABS, brake assist system (BAS) or VDC.
When [Adaptive] is selected, no warning vibra-
tion occurs if:
•You have switched on the turn signals. In
this case the warnings are suppressed for a
certain period of time.
•A driving system intervenes, such as ABS,
BAS or VDC.
•You accelerate forcefully.
•You brake forcefully.
•You steer actively, for example, swerve to
avoid an obstacle or change lane quickly.
•You cut the corner on a sharp bend.
The system may detect certain conditions and
warns you accordingly.The warning vibration occurs earlier if:
•You approach the outer lane marking on a
bend.
•The road has very wide lanes, for example, a
freeway.
•The system detects solid lane markings.
The warning vibration occurs later if:
•The road has narrow lanes.
•You cut across a corner on a bend.
LDW SYSTEM LIMITATIONS
WARNING
Listed below are the system limitations for the
LDW system. Failure to operate the vehicle in
accordance with these system limitations
could result in serious injury or death.
•This system is only a warning device to
inform the driver of a potential unintended
lane departure. It will not steer the vehicle
or prevent loss of control. It is the driver’s
responsibility to stay alert, drive safely,
keep the vehicle in the traveling lane, and
be in control of the vehicle at all times.
•The system will not operate at speeds be-
low approximately 40 MPH (60 km/h) or if it
cannot detect lane markers.
NSD599Assistance graphic
Starting and driving5-31