2017 INFINITI QX30 child lock

WARNING
•The seatback should not be reclined any
more than needed for comfort. Seat belts
are most effective when the passenger sits
well back and straight up in the seat. If the
seat back is reclined, the risk of sliding un-
der the lap belt and being injured is in-
creased.
•For the most effective protection when the
vehicle is in motion, the seat should be up-
right. Always sit well back and upright in the
seat with both feet on the floor and adjust
the seat properly. (SeeSeat beltslater in
this section.)
•After adjustment, gently rock in the seat to
make sure it is securely locked.
•To help avoid risk of injury or death through
unintended operation of the vehicle and/or
its systems, do not leave children, people
who require the assistance of others, or
pets unattended in your vehicle. Addition-
ally, the temperature inside a closed vehicle
on a warm day can quickly become high
enough to cause a significant risk of injury
or death to people and pets.
•Do not leave children unattended inside the
vehicle. They could unknowingly activate
switches or controls. Unattended children
could become involved in serious accidents.
•Do not adjust the driver’s seat while driving
so full attention may be given to vehicle
operation. The seat may move suddenly and
could cause loss of control of the vehicle.
CAUTION
When adjusting the seat positions, be sure not
to contact any moving parts to avoid possible
injuries and/or damage.
SSS0133AZ
SEATS
1-2Safety — seats, seat belts and supplemental restraint system

SEAT BELT WARNING LIGHT
The seat belt warning light reminds you to
fasten your seat belts. The light illuminates if
the engine is started, all doors are closed and
the driver’s and/or front passenger’s seat belt
is unfastened. It will remain illuminated until
the driver and/or front passenger fastens their
seat belt. A chime will sound once the vehicle is
in motion.
If the seat belt warning light flashes, together
with an intermittent warning tone, this means
that the driver or passenger has not fastened
their seat belt, and the speed of the vehicle is
exceeding 15 MPH (25 km/h).
For additional information, refer toWarning
lights, indicator lights and audible reminders
in the2. Instruments and controlssection.
THREE-POINT TYPE SEAT BELT WITH
RETRACTOR
WARNING
•Every person who drives or rides in this
vehicle should use a seat belt at all times.
Children should be in the rear seats and in
an appropriate restraint.
•Do not ride in a moving vehicle when the
seatback is reclined. This can be dangerous.
The shoulder belt will not be against your
body. In an accident, you could be thrown
into it and receive neck or other serious in-
juries. You could also slide under the lap
belt and receive serious internal injuries.
•For the most effective protection when the
vehicle is in motion, the seat should be up-
right. Always sit well back and upright in the
seat with both feet on the floor and adjust
the seat belt properly.
•Do not allow children to play with the seat
belts. Most seating positions are equipped
with Automatic Locking Retractor (ALR)
mode seat belts. If the seat belt becomes
wrapped around a child’s neck with the ALR
mode activated, the child can be seriously
injured or killed if the seat belt retracts and
becomes tight. This can occur even if thevehicle is parked. Unbuckle the seat belt to
release the child. If the seat belt cannot be
unbuckled or is already unbuckled, release
the child by cutting the seat belt with a
suitable tool (such as a knife or scissors) to
release the seat belt.
Fastening the seat belts
1. Adjust the seat. (SeeSeatsearlier in this
section.)
2. Slowly pull the seat belt out of the retractor
and insert the tongue into the buckle until
you hear and feel the latch engage.NIC2743
1-14Safety — seats, seat belts and supplemental restraint system

•The retractor is designed to lock during a
sudden stop or on impact. A slow pulling
motion permits the belt to move and al-
lows you some freedom of movement in
the seat.
•If the seat belt cannot be pulled from its
fully retracted position, firmly pull the belt
and release it. Then smoothly pull the belt
out of the retractor.
3. Position the lap belt portionlow and snug on
the hipsas shown4. Pull the shoulder belt portion toward the
retractor to take up extra slack. Be sure the
shoulder belt is routed over your shoulder
and across your chest.
The front passenger seat and the rear seating
positions three-point seat belts have two
modes of operation:
•Emergency Locking Retractor (ELR)
•Automatic Locking Retractor (ALR)
The ELR mode allows the seat belt to extend and
retract to allow the driver and passengers some
freedom of movement in the seat. The ELR locks
the seat belt when the vehicle slows down
rapidly or during certain impacts.The ALR mode (child restraint mode) locks the
seat belt for child restraint installation. When
the ALR mode is activated, the seat belt cannot
be extended again until the seat belt tongue is
detached from the buckle and fully retracted.
The seat belt returns to the ELR mode after the
seat belt fully retracts. For additional informa-
tion, refer toChild restraintslater in this
section. The ALR mode should be used only for
child restraint installation. During normal seat
belt use by an occupant, the ALR mode should
not be activated. If it is activated, it may cause
uncomfortable seat belt tension. It can also
change the operation of the front passenger air
bag. For additional information, refer toFront
passenger air bag and status lightin the1.
Safety — seats, seat belts and supplemental
restraint systemSafety — seats, seat belts and
supplemental restraint systemsection.WARNING
When fastening the seat belts, be certain that
the seatbacks are completely secured in the
latched position. If they are not completely
secured, passengers may be injured in an acci-
dent or sudden stop.
SSS0292ZSSS0290Z
Safety — seats, seat belts and supplemental restraint system1-15

WARNING
Do not allow children to play with the seat
belts. Most seating positions are equipped
with Automatic Locking Retractor (ALR) mode
seat belts. If the seat belt becomes wrapped
around a child’s neck with the ALR mode acti-
vated, the child can be seriously injured or
killed if the seat belt retracts and becomes
tight. This can occur even if the vehicle is
parked. Unbuckle the seat belt to release the
child. If the seat belt can not be unbuckled or is
already unbuckled, release the child by cutting
the seat belt with a suitable tool (such as a
knife or scissors) to release the seat belt.
Children need adults to help protect them.
They need to be properly restrained.
In addition to the general information in this
manual, child safety information is available
from many other sources, including doctors,
teachers, government traffic safety offices, and
community organizations. Every child is differ-
ent, so be sure to learn the best way to trans-
port your child.
There are three basic types of child restraint
systems:
•Rear-facing child restraint
•Forward-facing child restraint
•Booster seat
The proper restraint depends on the child’s
size. Generally, infants up to about 1 year and
less than 20 lb (9 kg) should be placed in
rear-facing child restraints. Forward-facing child
restraints are available for children who out-
grow rear-facing child restraints and are at least
1 year old. Booster seats are used to help
position a vehicle lap/ shoulder belt on a child
who can no longer use a forward-facing child
restraint.
WARNING
Infants and children need special protection.
The vehicle’s seat belts may not fit them prop-
erly. The shoulder belt may come too close to
the face or neck. The lap belt may not fit over
their small hip bones. In an accident, an im-
properly fitting seat belt could cause serious or
fatal injury. Always use appropriate child
restraints.
All U.S. states and Canadian provinces or terri-
tories require the use of approved child re-
straints for infants and small children. See
Child restraintsin the1. Safety — seats, seat
belts and supplemental restraint systemsec-
tion for more information.A child restraint may be secured in the vehicle
by using either the LATCH (Lower Anchor and
Tethers for CHildren) system or with the vehicle
seat belt. For additional information, refer to
Child restraintsin the1. Safety — seats, seat
belts and supplemental restraint systemsec-
tion.
INFINITI recommends that all pre-teens and chil-
dren be restrained in the rear seat. Studies show
that children are safer when properly restrained
in the rear seat than in the front seat.
This is especially important because your ve-
hicle has a supplemental restraint system (air
bag system) for the front passenger. (See
Supplemental Restraint System (SRS)later in
this section.)
INFANTS
Infants up to at least 1 year old should be
placed in a rear-facing child restraint. INFINITI
recommends that infants be placed in child
restraints that comply with Federal Motor Ve-
hicle Safety Standards or Canadian Motor Ve-
hicle Safety Standards. You should choose a
child restraint which fits your vehicle and al-
ways follow the manufacturer’s instructions for
installation and use.
CHILD SAFETY
1-18Safety — seats, seat belts and supplemental restraint system

REAR-FACING CHILD RESTRAINT
INSTALLATION USING THE SEAT BELTS
WARNING
The three-point seat belt with Automatic Lock-
ing Retractor (ALR) must be used when install-
ing a child restraint. Failure to use the ALR
mode will result in the child restraint not being
properly secured. The restraint could tip over
or be loose and cause injury to a child in a
sudden stop or collision.
Rear-facing child restraints must not be used
on the front seats.
For additional information, refer to all Warnings
and Cautions in theChild safetyin the1.
Safety — seats, seat belts and supplemental
restraint systemSafety — seats, seat belts and
supplemental restraint systemsection and
Child restraintsin the1. Safety — seats, seat
belts and supplemental restraint systemsec-
tion before installing a child restraint.Do not use the lower anchors if the combined
weight of the child and the child restraint
exceeds 65 lb (29.5 kg). If the combined weight
of the child and the child restraint is greater
than 65 lb (29.5 kg), use the vehicle seat belt
(not the lower anchors) to install the child
restraint. Be sure to follow the child restraint
manufacturer’s instructions for installation.
Follow these steps to install a rear-facing child
restraint using the vehicle seat belts in the rear
seats:
1.Child restraints for infants must be used in
the rear-facing direction and therefore must
not be used in the front seat.Position the
child restraint on the seat. Always follow the
child restraint manufacturer’s instructions.
WRS0256ZRear-facing — step 1
1-26Safety — seats, seat belts and supplemental restraint system

5. Remove any additional slack from the seat
belt; press downward and rearward firmly in
the center of the child restraint to compress
the vehicle seat cushion and seatback while
pulling up on the seat belt.6.After attaching the child restraint, test it
before you place the child in it. Push it from
side to side while holding the child restraint
near the seat belt path. The child restraint
should not move more than 1 inch (25 mm),
from side to side. Try to tug it forward and
check to see if the belt holds the restraint in
place. If the restraint is not secure, tighten the
seat belt as necessary, or put the restraint in
another seat and test it again. You may need
to try a different child restraint. Not all child
restraints fit in all types of vehicles.
7.Check to make sure that the child restraint is
properly secured prior to each use. If the seat
belt is not locked, repeat steps 1 through 6.
After the child restraint is removed and the
seat belt fully retracted, the ALR mode (child
restraint mode) is canceled.
FORWARD-FACING CHILD RESTRAINT
INSTALLATION USING LATCH
For additional information, refer to all Warnings
and Cautions in theChild safetyin the1.
Safety — seats, seat belts and supplemental
restraint systemSafety — seats, seat belts and
supplemental restraint systemsection and
Child restraintsin the1. Safety — seats, seat
belts and supplemental restraint systemsec-
tion before installing a child restraint.
Do not use the lower anchors if the combined
weight of the child and the child restraint
exceeds 65 lb (29.5 kg). If the combined weight
of the child and the child restraint is greater
than 65 lb (29.5 kg), use the vehicle seat belt
(not the lower anchors) to install the child
restraint. Be sure to follow the child restraint
manufacturer’s instructions for installation.
Follow these steps to install a forward-facing
child restraint in the rear seats using the LATCH
system:
1. Position the child restraint on the seat.
Always follow the child restraint manufactur-
er’s instructions.
WRS0762ZRear-facing — step 5SSS0658ZRear-facing — step 6
1-28Safety — seats, seat belts and supplemental restraint system

Outboard seating positions with removable
head restraints/headrests:
1. If necessary, raise or remove the head
restraint/headrest and store it in a secure
place. Be sure to reinstall the head restraint/
headrest when the child restraint is re-
moved. For additional information about
head restraint/headrest adjustment, removal
and installation, refer toHead
restraints/Headrestsin the1. Safety —
seats, seat belts and supplemental restraint
systemsection.
2. Position the top tether strap
1over the
seatback.
3. Secure the tether strap to the tether anchor
point
2on the seatback behind the child
restraint.
4. Tighten the tether strap according to the
manufacturer’s instructions to remove any
slack.Outboard seating positions with fixed head
restraints/headrests
:
1. If the child restraint has a single tether
strap, route the strap
1over the top of the
outer head restraint/headrest. If the child
restraint has two tether straps, route them
round each side of the outer head restraint/
headrest.
2. Secure the tether strap to the tether anchor
point
2on the seatback behind the child
restraint.
3. Tighten the tether strap according to the
manufacturer’s instructions to remove any
slack.
If you have any questions when installing a
top tether strap, it is recommended that you
visit an INFINITI retailer for this service.
FORWARD-FACING CHILD RESTRAINT
INSTALLATION USING THE SEAT BELTS
WARNING
The three-point seat belt with Automatic Lock-
ing Retractor (ALR) must be used when install-
ing a child restraint. Failure to use the ALR
mode will result in the child restraint not being
properly secured. The restraint could tip over
or be loose and cause injury to a child in a
sudden stop or collision. Also, it can change
the operation of the front passenger air bag.
For additional information, refer toFront pas-
senger air bag and status lightin the1. Safety
— seats, seat belts and supplemental restraint
systemsection.
For additional information, refer to all Warnings
and Cautions in theChild safetyin the1.
Safety — seats, seat belts and supplemental
restraint systemSafety — seats, seat belts and
supplemental restraint systemsection and
Child restraintsin the1. Safety — seats, seat
belts and supplemental restraint systemsec-
tion before installing a child restraint.
Safety — seats, seat belts and supplemental restraint system1-31

6. Remove any additional slack from the seat
belt; press downward and rearward firmly in
the center of the child restraint with your
knee to compress the vehicle seat cushion
and seatback while pulling up on the seat
belt.
7. Tighten the tether strap according to the
manufacturer’s instructions to remove any
slack.8. After attaching the child restraint, test it
before you place the child in it. Push it from
side to side while holding the child restraint
near the seat belt path. The child restraint
should not move more than 1 inch (25 mm),
from side to side. Try to tug it forward and
check to see if the belt holds the restraint in
place. If the restraint is not secure, tighten
the seat belt as necessary, or put the re-
straint in another seat and test it again. You
may need to try a different child restraint.
Not all child restraints fit in all types of
vehicles.
9. Check to make sure the child restraint is
properly secured prior to each use. If the
seat belt is not locked, repeat steps 2
through 8.10. If the child restraint is installed in the front
passenger seat, place the ignition switch in
the ON position. The front passenger air
bag status OFF light should illuminate. If
this light is not illuminated refer toFront
passenger air bag and status lightin the
1. Safety — seats, seat belts and supple-
mental restraint systemsection.Move the
child restraint to another seating position.
Have the system checked. It is recom-
mended you visit an INFINITI retailer for this
service. After the child restraint is removed
and the seat belt is fully retracted, the ALR
mode (child restraint mode) is canceled.
WRS0681ZForward-facing — step 6WRS0698ZForward-facing — step 8SSS0676ZForward-facing — step 10
1-34Safety — seats, seat belts and supplemental restraint system