2016 Citroen C4 PICASSO Owner's Manual

135
C4-Picasso-II_en_Chap04_conduite_ed01-2016
Emergency braking
In the event of a failure of the main service
brake  or   in   an   exceptional   situation   (e.g.   driver  
t

aken   ill,   under   instruction,   etc.)   a   continuous  
p

ull   on   the   control   lever   will   brake   the   vehicle.  
B

raking   takes   place   while   the   control   lever   is  
b

eing   pulled.   It   is   interrupted   if   the   control   lever  
i

s
 r
eleased.
The ABS and DSC systems provide stability of
the
  vehicle   during   emergency   braking.
If
  the   emergency   braking   malfunctions,   the  
m

essage   "Parking   brake   control   faulty"   will   be  
d

isplayed.
If a failure of the ABS and DSC systems occurs,
signalled
  by   the   illumination   of   one   or   both
 w

arning   lamps   in   the   instrument   panel,   then
 s

tability   of   the   vehicle   is   no   longer   guaranteed.
In this event, stability must be assured by the
driver
  by   repeating   alternate   "pull-release"
 a

ctions on the control lever until the vehicle is
immobilised. The
  emergency   braking   should   only   be  
u

sed   in   an   exceptional   situation.
Repeat this procedure to reactivate automatic
operation.
Reactivation of automatic operation is
confirmed by the indicator lamp in the
instrument
 
panel
 
going
 
off.
Deactivating automatic operation
In some situations, such as very cold weather
or   towing   (caravan,   recovery),   it   may   be  
n

ecessary to deactivate automatic operation of
the
  system.
F
 
S
tart   the   engine.
F
 
A
pply   the   parking   brake   with   the   control  
l

ever,   if   it   is   released.
F
 
T
ake   your   foot   off   the   brake   pedal.
F

P
ush and hold the control lever in the
release direction for at least 10 seconds
and
  no   more   than   15   seconds.
F
 
R
elease   the   control   lever.
F
 
P
ress   and   hold   the   brake   pedal.
F

P
ull the control lever in the apply direction
for
  2   seconds.
Deactivation of the automatic functions
is confirmed by illumination of this
indicator
  lamp   in   the   instrument   panel.
F
 
R
elease   the   control   lever   and   the   brake  
ped

al. From
  this   point   the   parking   brake   can   only  b
e   applied   and   released   manually   using   the  
c

ontrol   lever.
4
Driving

136
C4-Picasso-II_en_Chap04_conduite_ed01-2016
Operating faults
The various alert situations are described in the table below.
I n   the   event   of   a   fault   with   the   electric   parking   brake   it   is   recommended   that   you   contact   a   CITROËN   dealer   or   a   qualified   workshop   without   delay.
Situations Consequences
Display
  of   the   message   "Parking brake fault " and this
warning
 lam

p: -
 
A
utomatic   release   is   not   available.
-
 
I
f   you   attempt   an   automatic   release,   a   help   message   is   displayed   on   acceleration  
w

hen   the   parking   brake   is   applied,   prompting   you   to   use   manual   release.
Display
  of   the   message   "Parking brake fault " and these
warning
 lam

ps: -
 
S
econdary   braking   does   not   have   full   power.
-
 
I
f   automatic   release   is   not   available,   a   help   message   is   displayed   on   acceleration  
w

hen   the   parking   brake   is   applied,   prompting   you   to   use   manual   release.
Display
  of   the   message   "Parking brake fault " and these
warning
 lam

ps: -
 
A
utomatic   application   is   not   available:   use   the   control   lever.
-
 
T
he   electric   parking   brake   can   only   be   used   manually.
-
 
I
f   automatic   release   is   also   not   available,   a   help   message   is   displayed   on  
a

cceleration   when   the   parking   brake   is   applied,   prompting   you   to   use   manual  
r

elease.
Display
  of   the   message   "Parking brake fault " and these
warning
 lam

ps: -
 
I
f   manual   application   and   release   do   not   work,   the   control   lever   is   faulty.
-
 
T
he   automatic   functions   must   be   used   in   all   circumstances:   they   are  
a

utomatically   reactivated   in   the   event   of   failure   of   the   control   lever.
-
 
Y
ou   can   no   longer   immobilise   the   vehicle   with   the   engine   running.
Driving

137
C4-Picasso-II_en_Chap04_conduite_ed01-2016
SituationsConsequences
Display   of   the   message   "Parking brake fault " and these
warning
 lam

ps: The
  parking   brake   is   faulty,   the   manual   and   automatic   functions   may   not   operate.
When stationary ,
  to   immobilise   your   vehicle:
-
 
P
ull   and   hold   the   control   lever   for   about   7   to   15   seconds,   until   the   warning   lamp  
c

omes   on   in   the   instrument   panel.
If
  this   procedure   does   not   work,   you   should   make   your   vehicle   safe:
-
 
P
ark   on   a   level   sur face.
-
 
E
ngage   a   gear   with   a   manual   gearbox,   or   place   the   gear   selector   at   position   P
with
  an   automatic   gearbox.
-
 
I
f   possible,   fit   a   wheel   chock.
Call
  on   a   CITROËN   dealer   or   a   qualified   workshop.
Display
  of   the   message   "Parking brake fault " and these
warning
 lam

ps: -
 
T
he   parking   brake   does   not   have   its   full   per formance   to   securely   hold   the   vehicle  
i

n   all   situations.
You
  should   make   your   vehicle   safe:
-
 
P
ark   on   a   level   sur face.
-
 
E
ngage   a   gear   with   a   manual   gearbox,   or   place   the   gear   selector   at   position P
with
  an   automatic   gearbox.
-
 
I
f   possible,   fit   a   wheel   chock.
Call
  on   a   CITROËN   dealer   or   a   qualified   workshop.
The
  flashing   of   the   P   warning   lamps   on   starting   the   vehicle   indicates   that   the   parking  
b

rake   is   not   correctly   applied.
As
  soon   as   possible,   stop   the   vehicle   and   try   to   completely   release   the   parking   brake,  
u

sing   the   control   lever,   with   your   foot   on   the   brake   pedal.
Display
  of   the   message   "Battery fault "
  and   this   warning   lamp:-
 
T
he   state   of   charge   of   the   battery   is   very   low   and   requires   immobilisation   of   the  
v

ehicle   in   a   safe   place:   engage   a   gear   with   a   manual   gearbox   or   fit   a   chock   to  
o

ne   of   the   wheels.
-
 
O
nce   the   battery   is   completely   discharged,   the   controls   do   not   operate:   to  
r

elease   the   parking   brake,   call   on   a   CITROËN   dealer   or   a   qualified   workshop.
4
Driving

138
C4-Picasso-II_en_Chap04_conduite_ed01-2016
Hill start assist
System which keeps your vehicle immobilised temporarily   (approximately   2   seconds)   when  
s

tarting   on   a   gradient,   the   time   it   takes   to  
m

ove   your   foot   from   the   brake   pedal   to   the  
a

ccelerator
 ped
al.
This
  system   only   operates   when:
-

t
he vehicle is completely stationary, with
your
  foot   on   the   brake   pedal,
-

c
ertain conditions of slope are met,
-
 
w
ith   the   driver’s   door   closed.
The hill start assist system cannot be
deactivated.
On an ascending slope, with the vehicle
stationary, the vehicle is held momentarily
when you release the brake pedal:
-
 
p
rovided   you   are   in   first   gear   or   neutral   with  
a

  manual   gearbox,
-

p
rovided you are in position D or M with an
automatic
  gearbox.Operation
On a descending slope, with the vehicle
stationary and reverse gear engaged, the
vehicle is held momentarily when you
release the brake pedal.
Operating fault
If a fault in the system occurs, these warning lamps come on, accompanied by an alert
message.
  Contact   a   CITROËN   dealer   or  
a

  qualified   workshop   to   have   the   system  
c

hecked.
Do
 
not
 
get
 
out
 
of
 
the
 
vehicle
 
while
 
it
 
is
 
b

eing
 
held
 
in
 
the
 
hill
 
start
 
assist
 
phase.
If
 
you
 
need
 
to
 
exit
 
the
 
vehicle
 
with
 
t

he
 
engine
 
running,
 
apply
 
the
 
parking
 
b

rake
 
manually
 
then
 
ensure
 
that
 
the
 
p

arking
 
brake
 
warning
 
lamp
 
(and
 
the
 
w

arning
 lam

p
 P

in the lever of the
electric
 
parking
 
brake)
 
are
 
on
 
fixed
 
(not
 
f

lashing).
Driving

139
C4-Picasso-II_en_Chap04_conduite_ed01-2016
5-speed manual
gearbox
Engaging reverse gear
F With the clutch pedal fully down, place the gear   lever   in   neutral.
F
 
P
ush   the   gear   lever   to   the   right   then  
ba

ckwards.
Only
  engage   reverse   gear   when   the
 v

ehicle   is   stationary   with   the   engine   at   idle.
As a safety precaution and to facilitate
starting
  of   the   engine:
-

a
lways select neutral,
-
 
p
ress   the   clutch   pedal.
6-speed manual
gearbox
Engaging 5th or 6th gear
F Move  the   lever   fully   to   the   right   to   engage  5th or 6th ge a r.
Only   engage   reverse   gear   when   the
 v

ehicle   is   stationary   with   the   engine   at   idle.
As a safety precaution and to facilitate
starting
  of   the   engine:
-

a
lways select neutral,
-
 
p
ress   the   clutch   pedal.
Engaging reverse gear
Failure to follow this advice may cause
permanent  damage   to   the   gearbox  
(

engagement
 o
f
 3rd or 4th gear by m
i st a ke).
F
 
R
aise   the   ring   under   the   knob   and   move  
t

he   gear   lever   to   the   left   then   for wards.
4
Driving

140
C4-Picasso-II_en_Chap04_conduite_ed01-2016
Automatic gearbox
This gearbox offers two driving modes.
- a utomated mode for automatic
management
  of   the   gears   by   the   gearbox,  
w

ithout any action on the part of the driver,
-

m
anual
 
mode   for   sequential   gear   changing  
b

y   the   driver   using   the   steering   mounted  
p

addles.
P.
 Pa

rk.
-
 
I
mmobilisation   of   the   vehicle,   parking   brake  
a

pplied   or   released.
-
 
S
tarting   the   engine.
R.
 R

everse.
-
 
R
eversing,   vehicle   stationary   and   engine   at  
i

dle.
N.
 N

eutral.
-
 
I
mmobilisation   of   the   vehicle,   parking   brake  
a

pplied.
-
 
S
tarting   the   engine.
D.
 A

utomatic
 ope
ration.
M.
 M

anual   operation   with   sequential   changing  
o

f   the   six   gears.Gear selector lever
To select position P,   move   the   gear  s
elector   to   the   highest   position  
(

towards

R), then push it for wards and
then
  to   the   left.
Only
  engage   it   when   the   vehicle   is   at   a  
c

omplete   stop.   In   this   position,   the   front  
w

heels   are   locked.   Ensure   that   the   gear  
s

elector   is   correctly   positioned.
To
  move   the   gear   selector,   switch   on  
t

he   ignition   or   start   the   engine.
If
  the   battery   is   not   sufficiently   charged,  
i

t   is   not   possible   to   move   the   gear  
s

elector.
To come out of position P
, move the
gear   selector   to   the   right   to   the   desired  
p

osition,   while   keeping   your   foot   on   the  
b

rake
 ped
al.
It
 
is
 
possible
 
to
 
change
 
from
 
one
 
mode
 
t

o
 
the
 
other
 
at
 
any
 
time.
With the automated mode, you can
temporarily
 
take
 
control
 
of
 
the
 
gear
 
c

hanges
 
at
 
any
 
time.
Driving

141
C4-Picasso-II_en_Chap04_conduite_ed01-2016
+. Control  paddle   for   changing   up,   to   the   right  o
f   the   steering   wheel.
F

P
ull the " +"
  paddle   towards   you   to   change   up.
-.
 C

ontrol   paddle   for   changing   down,   to   the  
l

eft   of   the   steering   wheel.
F

P
ull the " -"
  paddle   towards   you   to   change  
d

own.
Steering mounted control paddles
The steering mounted control paddles cannot be used to select neutral or to
select
  or   come   out   of   reverse. When
  you   move   the   gear   selector,   the   symbol  
c

orresponding   to   its   position   is   displayed   in   the  
in

strument
 pan
el.
P.
 Pa
rk.
R.
 R
everse.
N.
 N
eutral.
D.
 D
rive
 (
automatic
 ope
ration).
1 to 6.   Gears   engaged   in   manual   operation.
-.
 I
nvalid   value   in   manual   operation.
Displays in the instrument panelMoving off
F With
  your   foot   on   the   brake   pedal,   select  p
osition P or N .
F
 
S
tart   the   engine.
If P is displayed in the instrument panel,
although
  the   gear   selector   is   in   another  
p

osition,   place   the   gear   selector   in  
p

osition P   to   be   able   to   start   the   engine.
F
 
W
ith   the   engine   running,   press   the   brake  
ped

al.
F

Sel
ect automated mode (position D ),
manual mode (position M ) or reverse
(position R ).
If you do not press the
brake
  pedal   to   come   out   of  
p

osition P,
  this   warning   lamp  
I
f these conditions are not met, there
is
  an   audible   signal   accompanied   by   a  
m

essage.
or symbol appears in the instrument
panel,
  accompanied   by   the   message  
"

Place   automatic   gearbox   in   position P",
flashing
  of   P in the instrument panel
and
  an   audible   signal.
4
Driving

142
C4-Picasso-II_en_Chap04_conduite_ed01-2016
F Check  that   the   symbol   displayed   in   the  i
nstrument   panel   agrees   with   the   position  
o

f   the   selector.
F
 
P
rogressively   release   the   brake   pedal.
F
 
I
f   the   parking   brake   is   released,   the   vehicle  
m

oves   off.
 I

f   the   parking   brake   is   applied   and  
a

utomatic operation is activated, accelerate
away.
Never
  press   the   accelerator   and   brake  
p

edals   at   the   same   time.   Braking   and  
a

cceleration should be done only with
the
  right   foot.   Pressing   both   pedals  
t

ogether   risks   damaging   the   gearbox.
If
  the   brake   does   not   release  
a

utomatically,   check   that   the   front   doors  
a

re   correctly   closed. Never leave children unsupervised in
the
  vehicle   when   the   engine   is   running.
When
  carrying   out   a   maintenance  
o

peration   with   the   engine   running,  
a
pply  
t

he   parking   brake   and   select   position   P. Never select position P or R unless the
vehicle is at a complete stop with the
brake
 a

pplied.
When
  you   want   to   engage   reverse,  
t

o   avoid   jolts,   do   not   accelerate  
i

mmediately   after   engaging   R.
Changing
 in

to
 p
osition
 R
is
accompanied
  by   an   audible   signal.
Never select position N
  when   driving.  
I

f position N is   engaged   in   error   when  
m

oving,   allow   the   engine   to   idle,   then  
e

ngage   position   D   to   accelerate.
When
  the   engine   is   running   at   idle,  
b

rakes   released,   if   position   R, D or M is
selected, the vehicle will move even if
the
  accelerator   is   not   pressed.
Driving