2015 SUZUKI NEXA Owners Manual

Downloaded from www.Manualslib.com manuals search engine 
(0(5*(1&<6(59,&(
06(
-DFNLQJ,QVWUXFWLRQV
75F062
1) Place the vehicle on level, hard ground.
2) Set the parking brake firmly and shift
into “R” (Reverse).
3) Turn on the hazard warning flasher if
your vehicle is near traffic.
4) Block the front and rear of the wheel
diagonally opposite of the wheel being
lifted.5) Place the spare wheel near the wheel
being lifted as shown in the illustration
in case that the jack slips.
54G253
63J10063J101
6) Position the jack at an angle as shown
in the illustration and raise the jack by
turning the jack handle clockwise until
the jack-head groove fits around the
jacking bar beneath the vehicle body.
7) Continue to raise the jack slowly and
smoothly until the tire clears the
ground. Do not raise the vehicle more
than necessary.
:$ 5 1 , 1 *

Downloaded from www.Manualslib.com manuals search engine (0(5*(1&<6(59,&(
06(
7R5DLVHWKH9HKLFOHZLWKD*DUDJH
-DFN• Apply the garage jack to one of the points
indicated below.
• Always support the raised vehicle with
jack stands (commercially available) at
the points indicated below.)URQWMDFNLQJSRLQWIRUJDUDJHMDFN
64MS178
5HDUMDFNLQJSRLQWIRUJDUDJHMDFN
64MS140
$SSOLFDWLRQSRLQWIRUMDFNVWDQG
RUWZRFROXPQOLIW
61MM0B103
:$ 5 1 , 1 *

Downloaded from www.Manualslib.com manuals search engine 
(0(5*(1&<6(59,&(
06(
NOTE:
For more details, please contact an
DXWKRULVHG0DUXWL6X]XNLZRUNVKRS.&KDQJLQJ:KHHOVTo change a wheel, use the following pro-
cedure:
1) Remove the jack, tools and spare
wheel from the vehicle.
2) Loosen, but do not remove the wheel
nuts.
3) Jack up the vehicle (follow the jacking
instructions in this section).
4) Remove the wheel nuts and wheel.
65J4033
5) Before installing the new wheel, clean
any mud or dirt off from the surface of
the wheel (1), hub (2), thread part (3)
and surface of the wheel nuts (4) with a
clean cloth. Clean the hub carefully; it
may be hot from driving.
6) Install the new wheel and replace the
wheel nuts with their cone shaped end
facing the wheel. Tighten each nut
snugly by hand until the wheel is
securely seated on the hub.
7LJKWHQLQJWRUTXHIRUZKHHOQXW
1PNJPOEIW
7) Lower the jack and fully tighten the nuts
in a crisscross fashion with a wrench as
shown in the illustration.
NOTICE
1HYHU DSSO\ D JDUDJH MDFN WR WKH
H[KDXVW SLSH VLGH XQGHU VSRLOHU LI
HTXLSSHG HQJLQH XQGHUFRYHU RU UHDU
WRUVLRQEHDP
:$ 5 1 , 1 *

Downloaded from www.Manualslib.com manuals search engine (0(5*(1&<6(59,&(
06(
-XPSVWDUWLQJLQVWUXFWLRQV
:KHQ-XPS6WDUWLQJ<RXU9HKLFOH
8VHWKH)ROORZLQJ3URFHGXUH1) Use only a 12-volt battery to jump start
your vehicle. Position the good 12-volt
battery close to your vehicle so that the
jump leads will reach both batteries.
When using a battery installed on
another vehicle, DO NOT LET THE
VEHICLES TOUCH. Set the parking
brakes fully on both vehicles.
2) Turn off all vehicle accessories, except
those necessary for safety reasons (for
example, headlights or hazard lights).
54MN259
3) Make jump lead connections as follows:
1. Connect one end of the first jump
lead to the positive (+) terminal of the
flat battery (1).
2. Connect the other end to the positive
(+) terminal of the booster battery (2).
3. Connect one end of the second jump
lead to the negative (–) terminal of the
booster battery (2).
4. Make the final connection to an
unpainted, heavy metal part (i.e.
engine mount bracket (3)) of the
engine of the vehicle with the flat bat-
tery (1).
:$ 5 1 , 1 *

Downloaded from www.Manualslib.com manuals search engine 
(0(5*(1&<6(59,&(
06(
4) If the booster battery you are using is fit-
ted to another vehicle, start the engine of
the vehicle with the booster battery. Run
the engine at moderate speed.5) Start the engine of the vehicle with the
flat battery.
6) Remove the jump leads in the exact
reverse order in which you connected
them.
7R Z L Q JIf you need to have your vehicle towed,
contact a professional service. Your dealer
can provide you with detailed towing
instructions.
:KHHO'ULYH:'0DQXDO7UDQ
VD[OHManual transaxle vehicles may be towed
using either of the following methods.
1) From the front, with the front wheels
lifted and the rear wheels on the ground.
Before towing, make sure that the park-
ing brake is released.
2) From the rear, with the rear wheels lifted
and the front wheels on the ground, pro-
vided the steering and drivetrain are in
operational condition. Before towing,
make sure that transaxle is in neutral,
the steering wheel is unlocked (vehicle
without keyless push start system - the
ignition key should be in the “ACC” posi-
tion) (vehicle with keyless push start sys-
tem - the ignition mode is ACC), and the
steering wheel is secured with a clamp-
ing device designed for towing service.
&$87,21
&RQQHFW WKH MXPS OHDG WR WKH HQJLQH
PRXQW EUDFNHW VHFXUHO\ ,I WKH MXPS
OHDG GLVFRQQHFWV IURP WKH HQJLQH
PRXQW EUDFNHW EHFDXVH RI YLEUDWLRQDW
WKH VWDUW RI WKH HQJLQH WKH MXPS OHDG
FRXOGEHFDXJKWLQWKHGULYHEHOWV
NOTICE
2EVHUYH WKH IROORZLQJ LQVWUXFWLRQV
ZKHQWRZLQJ\RXUYHKLFOH

Downloaded from www.Manualslib.com manuals search engine (0(5*(1&<6(59,&(
06(
,IWKH6WDUWHU'RHV1RW2SHUDWH1) Try turning the ignition switch to the
“START” position or try pressing the
engine switch to change the ignition
mode to START with the headlights
turned on to determine the battery condi-
tion. If the headlights go excessively dim
or go off, it usually means that either the
battery is flat or the battery terminal con-
tact is poor. Recharge the battery or cor-
rect battery terminal contact as
necessary.
,IWKH(QJLQHLV)ORRGHGIf the engine is flooded with the fuel, it may
be hard to start. If this happens, press the
accelerator pedal all the way to the floor
and hold it there while cranking the engine.
• For petrol engine model, do not operate
the starter motor for more than 12 sec-
onds.
• For diesel engine model, do not operate
the starter motor for more than 30 sec-
onds.
,IWKH(QJLQH2YHUKHDWVThe engine could overheat temporarily
under severe driving conditions. If the high
engine coolant temperature warning light
comes on as overheating during driving:
1) Turn off the air conditioner, if equipped.
2) Take the vehicle to a safe place and
park.
3) Let the engine run at the normal idle
speed for a few minutes until the high
engine coolant temperature warning
light goes off.
:$51,1*
,I \RX VHH RU KHDU HVFDSLQJ VWHDP
VWRS WKH YHKLFOH LQ D VDIH SODFH DQG
LPPHGLDWHO\WXUQRIIWKHHQJLQHWROHW
LWFRRO'RQRWRSHQWKHKRRGZKHQ
VWHDP LV SUHVHQW :KHQ WKH VWHDP
FDQQRORQJHUEHVHHQRUKHDUGRSHQ
WKH KRRG WR VHH LI WKH FRRODQW LV VWLOO
ERLOLQJ ,I LW LV \RX PXVW ZDLW XQWLO LW
VWRSVERLOLQJEHIRUH\RXSURFHHG

Downloaded from www.Manualslib.com manuals search engine 
(0(5*(1&<6(59,&(
06(
If the high engine coolant temperature
warning light does not go off:
1) Turn off the engine and check that the
water pump belt and pulleys are not
damaged or slipping. If any abnormality
is found, correct it.
2) Check the coolant level in the reservoir.
If it is found to be lower than the “LOW”
line, look for leaks at the radiator, water
pump, and radiator and heater hoses. If
you locate any leaks that may have
caused the overheating, do not run the
engine until these problems have been
corrected.
3) If you do not find a leak, carefully add
coolant to the reservoir and then the
radiator, if necessary. (Refer to “Engine
Coolant” in the “INSPECTION AND
MAINTENANCE” section.)
NOTE:
If your engine overheats and you are
unsure what to do, contact your DXWKRULVHG
0DUXWL6X]XNLZRUNVKRS.
65D350d
:DUQLQJ7ULDQJOH
MHO-07-001
In case of vehicle break-down or during
emergency stopping, where, your vehicle
could become a potential traffic hazard,
keep the warning triangle, provided with
your vehicle, on the road free from any
obstacles behind your vehicle so as to
warn the approaching traffic, at an approxi-
mate distance of 50-100 m. The reflecting
side of the triangle should face the on com-
ing traffic. Please activate the hazard
warning lamps before alighting the vehicle
to keep the warning triangle.
:$ 5 1 , 1 *

Downloaded from www.Manualslib.com manuals search engine (0(5*(1&<6(59,&(
06(
MHO-07-014
• Remove the warning triangle carefully
from the cover as shown by arrow 1.
• Open both the reflector arms as shown
by arrow and lock the arms with each
other with the clip provided in the right
arm. Open the bottom stand in counter
clock-wise direction as shown by arrow
3. Position the warning triangle behind
the vehicle on a plain surface.
• Reverse the removal procedure for keep-
ing inside the cover.
MHO-07-014