2015 SUZUKI NEXA Owners Manual

Downloaded from www.Manualslib.com manuals search engine 
23(5$7,1*<2859(+,&/(
06(
NOTE:
In the presence of strong radio signals or
noise, you may not be able to change the
ignition mode to ACC or ON or to start the
engine using the engine switch. In this
case, the information display on the instru-
ment cluster will show the following mes-
sage: KEY FOB NOT DETECTED.8QUHOHDVHG6WHHULQJ/RFN:DUQLQJIf the steering lock remains engaged when
you press the engine switch to change the
ignition mode to “ON”, the information dis-
play in the instrument cluster shows the
message: “TRN. STEERING WHEEL TO
RELEASE LOCK”. Refer to “Information
Display” in the ³%()25( '5,9,1*´ sec-
tion for details.
NOTE:
The steering lock may not be released if
some load is acting on the steering wheel.
If this happens, turn the steering wheel to
the right or left to relieve it from the load
before you press the engine switch again
to change to the desired ignition mode.
.H\OHVV3XVK6WDUW6\VWHP
LIHTXLSSHGProvided the keyless push start system
remote controller is within the “interior
workable area” (refer to the related expla-
nation in this section), you can use the
engine switch for starting the engine and
selecting an ignition mode (ACC or ON). In
addition, the following functions can be
used:
• Keyless entry function. Refer to “Keyless
Push Start System Remote Controller” in
the “BEFORE DRIVING” section for
details.
• Locking and unlocking doors (including
the tailgate) using a request switch.
Refer to “Keyless Push Start System
Remote Controller” in the “BEFORE
DRIVING” section for details.
• Immobilizer (anti-theft) function. Refer to
“Immobilizer System” in the “BEFORE
DRIVING” section for details.(QJLQH6ZLWFK,OOXPLQDWLRQThe engine switch is illuminated (lit) in the
following situations:
• When the engine is off and the driver’s
door is open or for 15 seconds after the
drivers door is closed.
• When the engine is off and the position
lights are on. The illumination will go out
when the position lights are turned off.
• When the engine is on and the position
lights and/or the headlights are on. Theillumination will go out when the head-
lights are turned off.
82K253
NOTE:
To save the battery, the illumination will be
automatically turned off when both of the
following conditions are simultaneously
met:
• The headlights and position lights are
turned off.
• A period of 15 minutes has elapsed after
opening the driver’s door.6HOHFWLRQRI,JQLWLRQ0RGHVPress the engine switch to select the
“ACC” or “ON” mode as follows when you
use an electric accessory or check the
operation of instruments without running
the engine.
1) Bring the keyless push start system
remote controller with you and sit in the
driver’s seat.

Downloaded from www.Manualslib.com manuals search engine (1)
(2)
23(5$7,1*<2859(+,&/(
06(
2) Without depressing the clutch pedal,
press the engine switch (1).
82K254
Every time you press the engine switch,
the ignition mode changes as follows.
57L31033
NOTE:
When selecting the ignition modes, the
information display in the instrument clus-
ter shows certain messages. Refer to
“Information Display” in the “BEFORE
DRIVING” section for details.,IWKH0$67(5:$51,1*LQGLFDWRUOLJKW
EOLQNV DQG WKH LJQLWLRQ PRGHV FDQQRW
EHVHOHFWHG
Your keyless push start system remote con-
troller may not be sensed as being within the
“interior workable area” (refer to the related
explanation in this section). Try again after
making sure you have the remote controller
with you. If the ignition modes still cannot be
selected, the battery of the remote controller
may be discharged. To be able to select an
ignition mode, you must then use the follow-
ing method:
58MST0302
1) Without depressing the brake pedal
and the clutch pedal, push the engine
switch (1).
2) Within about 10 seconds during which
the master warning indicator light in the
instrument cluster is blinking and the
“PLACE KEY FOB ON START
SWITCH” message appears on the
information display, touch the engineswitch with the lock button end of the
remote controller (2) for about 2 sec-
onds.
NOTE:
•
If you still cannot select the ignition
modes, there may be some problem with
the keyless push start system. Contact
an DXWKRULVHG 0DUXWL 6X]XNL ZRUNVKRS
for an inspection of the system.
• The immobilizer/keyless push start sys-
tem warning light will come on for about
5 seconds while the master warning indi-
cator light is blinking. In addition, the
information display in the instrument
cluster will show a message during this
time. Refer to “Information Display” in
the “BEFORE DRIVING” section for
details.
•
You may customize the system to cause
the interior buzzer to sound once for the
remote controller out of sensing range
warning. To incorporate this customiza-
tion, please contact an DXWKRULVHG0DUXWL
6X]XNLZRUNVKRS
• If the battery of the remote controller is
about to become completely discharged,
the corresponding message will appear
on the information display when you
press the engine switch to change the
ignition mode to ON. Refer to “Informa-
tion Display” in the “BEFORE DRIVING”
section for details. For details on replac-
ing the battery, refer to the “Keyless
Push Start System Remote Controller” in
the “BEFORE DRIVING” section.
(OFF)
ON ACC LOCK
(Audio equipment)
(;$03/(
(1)

Downloaded from www.Manualslib.com manuals search engine 
23(5$7,1*<2859(+,&/(
06(
5HPRWH&RQWUROOHU2XWVLGH:DUQLQJWhen either of the conditions described
below is met, the system issues the remote
controller outside warning by sounding the
interior and exterior buzzers. At the same
time, the immobilizer/keyless push start
system warning light comes on and the
master warning indicator light blinks.
• Any door is opened and then closed
while the remote controller is not inside
the vehicle and the engine is running or
the ignition mode has been changed to
“ACC” or “ON” by pressing the engine
switch.
• The remote controller is not inside the
vehicle when you attempt to start the
engine after changing the ignition mode
to “ACC” or “ON” by pressing the engine
switch.
61MM0A182
(1) Immobilizer/keyless push start sys-
tem warning light (blinks)
(2) Master warning indicator light (blinks)
NOTE:
• If the warning is given, locate the remote
controller as soon as possible.
• Any attempt to start the engine will fail
while the warning is active. The mes-
sage appearing on the information dis-
play in the instrument cluster will also
indicate this condition. Refer to “Informa-
tion display” in the “BEFORE DRIVING”
section for details.
• Normally, the immobilizer/keyless push
start system warning light should go out
and the master warning indicator light
should stop blinking shortly after the
remote controller is brought back inside
the vehicle. If they remain lit and blink-
ing, change the ignition mode to “LOCK”
(OFF) by pressing the engine switch and
then perform the engine starting opera-
tion. Refer to “Starting the Engine” in this
section.
• Always keep the remote controller with
you as the driver.
,QWHULRU:RUNDEOH$UHDIRU(QJLQH
6WDUWLQJ,JQLWLRQ0RGH6HOHFWLRQ
DQG5HPRWH&RQWUROOHU2XWVLGH
:DUQLQJ
61MM0B002
(1) Interior workable area
The interior workable area for these func-
tions is defined as all the interior spaces
except for the space above the instrument
panel.
NOTE:
• Even when the remote controller is in the
“interior workable area”, if it is in any of
the following conditions, you may not be
able to start the engine or select the igni-
tion modes, and the remote controller
outside warning may be given.
– The remote controller’s battery is low.
– The remote controller is affected by
strong radio signals or noise.
– The remote controller is in contact with
or covered by a metallic object.
(1)
(2)
(1)

Downloaded from www.Manualslib.com manuals search engine 23(5$7,1*<2859(+,&/(
06(
– The remote controller is in stowage
like the glove box or a door pocket.
– The remote controller is in the sun
visor pocket or on the floor.
• Even when the remote controller is out-
side the “interior workable” area, if it is in
any of the following conditions, you may
be able to start the engine or select the
ignition mode. The “remote controller
outside” warning may not be given at
that time.
– The remote controller is outside the
vehicle but very close to a door.
– The remote controller is on the instru-
ment panel.
3DUNLQJ%UDNH/HYHU
64MS185
(1) To set
(2) To release
(3) To release
The parking brake lever is located between
the seats. To set the parking brake, hold
the brake pedal down and pull the parking
brake lever all the way up. To release the
parking brake, hold the brake pedal down,
pull up slightly on the parking brake lever,
push the button on the end of the lever
with your thumb, and lower the lever to its
original position.
(2)
(3) (1)
(;$03/(
:$ 5 1 , 1 *

Downloaded from www.Manualslib.com manuals search engine 
23(5$7,1*<2859(+,&/(
06(
3DUNLQJ%UDNH5HPLQGHU%X]]HUA buzzer sounds intermittently to remind
you to release the parking brake if you start
the vehicle without releasing the parking
brake. Make sure that the parking brake is
fully released and the brake system warning
light turns off.
3HGDO
80J2121
&OXWFK3HGDOThe clutch pedal is used to disengage the
drive to the wheels when starting the
engine, stopping, or shifting the gearshift
lever. Depressing the pedal disengages the
clutch.%UDNH3HGDOYour vehicle is equipped with either front
and rear disc brakes or front disc brakes
and rear drum brakes. Depressing the
brake pedal applies both sets of brakes.
You may hear occasional brake squeal
when you apply the brakes. This is a nor-mal condition caused by environmental
factors such as cold, wet, snow, etc.
$FFHOHUDWRU3HGDOThis pedal controls the speed of the
engine. Depressing the accelerator pedal
increases power output and speed.
:$ 5 1 , 1 *
'R QRW GULYH ZLWK \RXU IRRW UHVWLQJ RQ
WKH FOXWFK SHGDO ,W FRXOG UHVXOW LQ
H[FHVVLYHFOXWFKZHDUFOXWFKGDPDJH
RUXQH[SHFWHGORVVRIHQJLQHEUDNLQJ
(2)
(1)
(3)(;$03/(
:$ 5 1 , 1 *
,IEUDNHVTXHDOLVH[FHVVLYHDQG
RFFXUVHDFKWLPHWKHEUDNHVDUH
DSSOLHG\RXVKRXOGKDYHWKHEUDNHV
FKHFNHGE\\RXU DXWKRULVHG 0DUXWL
6X]XNLZRUNVKRS
:$ 5 1 , 1 *
'R QRW ULGH WKH EUDNHV E\ DSSO\LQJ
WKHP FRQWLQXRXVO\ RU UHVWLQJ \RXU
IRRW RQ WKH SHGDO 7KLV ZLOO UHVXOW LQ
RYHUKHDWLQJ RI WKH EUDNHV ZKLFK
FRXOG FDXVH XQSUHGLFWDEOH EUDNLQJ
DFWLRQ ORQJHU VWRSSLQJ GLVWDQFHV RU
SHUPDQHQWEUDNHGDPDJH

Downloaded from www.Manualslib.com manuals search engine 23(5$7,1*<2859(+,&/(
06( 6WDUWLQJWKH(QJLQH
9HKLFOHZLWKRXW.H\OHVV3XVK
6WDUW6\VWHP
%HIRUH6WDUWLQJWKH(QJLQH
64MS146
1) Make sure the parking brake is set fully.
2) Shift into “N” (Neutral) and depress the
clutch pedal all the way to the floor. Hold
the clutch pedal while starting the
engine.
6WDUWLQJD&ROGDQG:DUP(QJLQH&ROGHQJLQH
Turn the ignition switch to the “ON” posi-
tion and wait until the glow plug indicator
goes out if it comes on. Crank the engine
by turning the ignition key to “START”.
Release the key when the engine starts.
:DUPHQJLQH
Crank the engine by turning the ignition
key to “START”. Release the key when the
engine starts.
&DXWLRQ ZKHQ VWRSSLQJ WKH HQJLQH ZLWK
WXUERFKDUJHU
When stopping the engine after climbing or
high speed driving, let the engine idle for
about one minute or more (if it is not pro-
hibited) to cool down the turbocharger and
engine oil. This is to prevent the engine oil
from over-deteriorating. Deteriorated
engine oil will damage the bearings of the
turbocharger.
5HVWDUWLQJ GLHVHO HQJLQH DIWHU IXHO
HPSW\VWRS
If the engine stops and the low fuel warning
light and the malfunction indicator light
come on, use the following procedure:
1) Fill the fuel tank.
2) Hold the ignition key in “ON” position for
5-10 seconds to feed fuel.
3) Perform above engine starting proce-
dure to start the engine.
If the malfunction indicator light still comes

on after the engine started, there may be

some problem with the engine. Ask your

DXWKRULVHG 0DUXWL 6X]XNL ZRUNVKRS
to have
the
engine inspected.
:$ 5 1 , 1 *

Downloaded from www.Manualslib.com manuals search engine 
23(5$7,1*<2859(+,&/(
06( 6WDUWLQJWKH(QJLQH
9HKLFOHZLWK.H\OHVV3XVK6WDUW
6\VWHP
%HIRUH6WDUWLQJWKH(QJLQH
64MS169
1) Make sure the parking brake is set fully.
2) Shift to “N” (Neutral) and fully depress
the clutch pedal. Hold the clutch and
brake pedals fully depressed.
82K254
3) The “PUSH START SWITCH” message
will appear on the information display in
the instrument cluster. Push the engine
switch (1). When the engine is started,
the starter motor will automatically stop.
NOTE:
• You do not need to keep the engine
switch pressed to start the engine.
• The engine of a manual transaxle vehi-
cle will not start unless the clutch pedal
is depressed.
• During the engine starting procedure,
messages on the information display will
help you. Refer to “Information Display”in the “BEFORE DRIVING” section for
details.
• You should turn off such loads as the
headlights and air conditioning system to
facilitate starting of the engine.
• Even if you fail to start the engine, the
starter motor will stop operating auto-
matically after a short time. After the
starter motor has stopped or if there is
some problem with the system, the
starter motor will rotate only while the
engine switch is being pressed.
6WRSSLQJWKHHQJLQH• Depress the engine switch to stop the
engine after the vehicle stopped com-
pletely.
• In case of emergency, you can stop the
engine by quickly pushing the engine
switch more than 3 times, or pushing
and holding the engine switch more than
2 seconds while the vehicle in motion.
NOTE:
Except in emergency, do not stop the
engine while the vehicle in motion.
The steering and braking operation will
require more efforts when the engine
stopped.
Refer to “Braking” in this section.
• If the engine has been stopped and
stayed as it as for while after the engine
was stopped unexpectedly or was raced
before stopped, a clicking sound may be
heard from around the engine when
engine restarted. This is not a malfunc-
(1)
:$ 5 1 , 1 *
0DNH VXUH WKDW WKH SDUNLQJ EUDNH LV
VHW IXOO\ DQG WKH WUDQVD[OH LV LQ 1HX
WUDO EHIRUH DWWHPSWLQJ WR VWDUW WKH
HQJLQH
NOTICE

Downloaded from www.Manualslib.com manuals search engine 23(5$7,1*<2859(+,&/(
06(
tion. In this case, always let the engine
idle before stop it.6WDUWLQJD&ROGDQG:DUP(QJLQH&ROGHQJLQH
Depress the clutch and brake pedals fully
and press the engine switch to crank the
engine. If the glow plug indicator light
comes on, the engine will start automati-
cally after the glow plug indicator light goes
off or 10 seconds past.
:DUPHQJLQH
Crank the engine by pressing the engine
switch to change the ignition mode to
“START”.&DXWLRQ ZKHQ VWRSSLQJ WKH HQJLQH ZLWK
WXUERFKDUJHU
When stopping the engine after climbing or
high speed driving, let the engine idle for
about one minute or more (if it is not pro-
hibited) to cool down the turbocharger and
engine oil. This is to prevent the engine oil
from over-deteriorating. Deteriorated
engine oil will damage the bearings of the
turbocharger.
5HVWDUWLQJ GLHVHO HQJLQH DIWHU IXHO
HPSW\VWRS
If the engine stops and the low fuel warn-
ing light and the malfunction indicator light
come on, use the following procedure:
1) Fill the fuel tank.
2) Press the engine switch to change the
ignition mode to “ON” for 5-10 seconds
to feed fuel.
3) Perform above engine starting proce-
dure to start the engine.
If the malfunction indicator light still comes
on after the engine started, there may be
some problem with the engine. Ask your
DXWKRULVHG0DUXWL6X]XNLZRUNVKRS to have
theengine inspected.
,IWKH0$67(5:$51,1*LQGLFDWRUOLJKW
EOLQNVDQGWKHHQJLQHFDQQRWEHVWDUWHG
Your keyless push start system remote
controller may not be sensed as being
within the interior workable area. Try again
after making sure that you have the remote
controller with you. If the engine still can-
not be started, the battery of the remote
controller may be discharged. You mustthen use the following method to be able to
start the engine.
58MST0302
1) Make sure the parking brake is set fully.
2) Shift to “N” (Neutral) and fully depress
the clutch pedal. Hold the clutch and
brake pedals fully depressed.
3) The “PUSH START SWITCH.” mes-
sage will appear on the information dis-
play in the instrument cluster. Press the
engine switch (1).
4) Within about 10 seconds of blinking of
the “MASTER WARNING” indicator
light in the instrument cluster, touch the
engine switch with the lock button end
of the remote controller (2) for about 2
seconds.
NOTE:
• If you still cannot start the engine after
several attempts using the above
NOTICE
'RQRWFUDQNWKHHQJLQHIRUPRUH
WKDQVHFRQGVDWDWLPH
,IWKHHQJLQHGRHVQ