2015 SUZUKI NEXA keyless entry
[x] Cancel search: keyless entryPage 23 of 288
Downloaded from www.Manualslib.com manuals search engine 2-4
BEFORE DRIVING
64MS0-74E
NOTE:
You can switch the function that unlocks all
doors from twice operations to once opera-
tion, and vice versa, via the setting mode
of the information display. For details on
how to use the information display, refer to
“Information Display” in this section.
To unlock the driver’s door only, insert the
key in that door lock and turn the top of the
key toward the front of the vehicle once.
64MS021
(1) LOCK
(2) UNLOCK
You can also lock or unlock all doors by
depressing the front or rear of the switch,
(3) respectively.NOTE:
• You can also lock or unlock all doors by
operating the transmitter or remote con-
troller. Refer to “Keyless Push Start Sys-
tem Remote Controller/Keyless Entry
System Transmitter” in this section.
• If your vehicle is equipped with the key-
less push start system, you can also lock
or unlock all doors by pushing the request
switch. Refer to “Keyless Push Start Sys-
tem Remote Controller/Keyless Entry
System Transmitter” in this section.NOTE:
• All doors are automatically unlocked
when you turn the ignition switch to the
“LOCK” position and pull out the key, or
press the engine switch to change the
ignition mode to LOCK (OFF).
• All doors are automatically locked for
safety when the vehicle speed reaches
15 km/h.
• You can change the automatic locking or
unlocking function mentioned above via
the setting mode of the information dis-
play. For details on how to use the infor-
mation display, refer to “Information
Display” in this section.
Child-Proof Locks (rear door)
61MM0A046
(1) Lock position
(2) Unlock position
Each of the rear doors is equipped with a
child-proof lock which can be used to help
prevent unwanted opening of the door
from inside the vehicle. When the lock
lever is in the lock position (1), the rear
door can only be opened from outside.
When the lock lever is in the unlock posi-
tion (2), the rear door can be opened from
inside or outside.
EXAMPLE
(1)
(2)
(3)
WA R N I N G
Be sure to place the child-proof lock
in the lock position whenever chil-
dren are seated in the rear.
EXAMPLE
Page 24 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
If you cannot unlatch the tailgate by pushing
the unlatch switch (1) due to a discharged
battery or malfunction, follow the proce-
dures below to unlatch the tailgate from
inside the vehicle.
1) Remove the luggage compartment
cover (if equipped) and fold the rear seat
forward for easier access. Refer to
“Folding Rear Seats” section for details
on how to fold the rear seat forward.
2) Push open the tailgate from inside by
pushing up on the emergency lever (2)
using a flat blade screwdriver or the jack
handle. The tailgate will be latched again
by closing the tailgate simply.
68LM246
If the tailgate cannot be unlatched by push-
ing the unlatch switch (1), have the vehicle
inspected by your D X W K R U L V H G 0 D U X W L 6 X ] X N L
Z R U N V K R S
. H \ O H V V 3 X V K 6 W D U W 6 \ V W H P 5 H P R W H
& R Q W U R O O H U . H \ O H V V ( Q W U \ 6 \ V W H P
7 U D Q V P L W W H U
64MS022
Your vehicle is equipped with either a key-
less push start system remote controller
(Type A) or a keyless entry system trans-
mitter (Type B). The remote controller has
a keyless entry system and a keyless push
start system. The transmitter has only a
keyless entry system. For details, refer to
the following explanations.
: $ 5 1 , 1 *
$ O Z D \ V P D N H V X U H W K D W W K H W D L O J D W H L V
F O R V H G D Q G O D W F K H G V H F X U H O \ & R P
S O H W H O \ F O R V L Q J W K H W D L O J D W H K H O S V S U H
Y H Q W R F F X S D Q W V I U R P E H L Q J W K U R Z Q
I U R P W K H Y H K L F O H L Q W K H H Y H Q W R I D Q
D F F L G H Q W & R P S O H W H O \ F O R V L Q J L W D O V R
K H O S V N H H S H [ K D X V W J D V H V I U R P H Q W H U
L Q J W K H Y H K L F O H
& $ 8 7 , 2 1
Page 28 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
80J056
(1) 80 cm (2 1/2 feet)
When the remote controller is within
approximately 80 cm (2 1/2 feet) from a
front door handle or the tailgate switch, you
can lock or unlock the doors by pushing
the request switch.
NOTE:
• If the remote controller is outside the
request switch operating range
described above, you will not be able to
operate the request switch.
• If the battery of the remote controller
runs down or there are strong radio
waves or noise, the request switch oper-
ating range may be reduced or the
remote controller may be inoperative.
• If the remote controller is too close to the
door glass, the request switches may not
operate.• If a spare remote controller is in the vehi-
cle, the request switches may not oper-
ate normally.
• The remote controller will only operate a
request switch if it is within the switch’s
operating range. For example, if the
remote controller is within the operating
range of the driver’s door request switch
but not the front passenger’s door
request switch or the tailgate request
switch, the driver’s door switch can be
operated but the front passenger’s door
switch or tailgate switch cannot be oper-
ated.
• Avoid operations of switch with sharp
objects.
NOTE:
The keyless push start system may not
function correctly in certain environments
or under certain operating conditions such
as the following:• When there are strong signals coming
from a television, power station or a cel-
lular phone.
• When the remote controller is in contact
with or covered by a metal object.
• When a radio wave type remote keyless
entry is used nearby.
• When the remote controller is placed
near an electronic device such as per-
sonal computer.
Some additional precautions you should
take and information you should be aware
of are:
• Make sure the key is stowed in the
remote controller. If the remote controller
becomes unreliable, you will not be able
to lock or unlock the doors.
• Be sure that the driver always carries the
remote controller.
•If you lose one of the remote controllers,
ask your
D X W K R U L V H G 0 D U X W L 6 X ] X N L
Z R U N V K R S as soon as possible for a
replacement. Be sure to have your
dealer program the
new remote
controller code in your vehi-cle’s
memory so that the old code is
erased.
• You can use up to four remote controllers
and the keys for your vehicle. Ask your
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S
for
details.
• The battery life of the remote controller is
about two years, but it can vary depend-
ing on usage conditions.
(1)
(1)(1)
( ; $ 0 3 / (
NOTICE
7 K H U H P R W H F R Q W U R O O H U L V D V H Q V L W L Y H
H O H F W U R Q L F L Q V W U X P H Q W 7 R D Y R L G G D P
D J L Q J W K H U H P R W H F R Q W U R O O H U
Page 32 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
NOTE:
If no door is opened within about 30 sec-
onds after the unlock button (2) is oper-
ated, the doors will automatically lock
again.
NOTE:
(For models with security system)
• If you lock the doors using the transmit-
ter when the engine hood is open, the
siren will sound 3 times to remind you.
• If the security system was triggered due
to an unauthorized entry into the vehicle
and then you unlock the doors using the
transmitter, the siren will sound 4 times
to remind you. If this happens, check
whether your vehicle has been broken
into while you were away from it.
• Once you push both of the “LOCK” but-
ton (1) and “UNLOCK” button (2), then
you push one of the buttons within 5 sec-
onds, the siren will not sound. However,
If you push one of the buttons twice
within 5 seconds, or push one of the but-
tons 5 seconds later, the siren will
sound.
• You can set whether the siren sounds
when locking or unlocking the door(s) via
the setting mode of the information dis-
play. For details on how to use the infor-
mation display, refer to “Information
Display” in this section.NOTE:
• The maximum operating distance of the
keyless entry system transmitter is about
5 m (16 ft.), but this can vary depending
on the surroundings, especially near
other transmitting devices such as radio
towers or CB (Citizen’s Band) radios.
• The door locks cannot be operated with
the transmitter, if the ignition key is
inserted in the ignition switch.
• When any door is open, the door locks
can be operated only by unlocking with
the transmitter. With this unlocking oper-
ation, the turn signal lights will flash
twice and the siren (if your vehicle is
equipped with the security system) will
sound twice.
• If you lose one of the transmitters, ask
your D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S
as soon as possible for a replacement.
Be sure to have your dealer program
the new transmitter code in your
vehicle’s memory so that the old code is
erased. 3 D Q L F D O D U P I X Q F W L R Q L I H T X L S S H G
This function is to get the attention of oth-
ers.
Push both of the “LOCK” button (1) and
“UNLOCK” button (2) for more than 3 sec-
onds. The turn signal lights will blink for
about 27.5 seconds. Also, the siren will
sound for about 27.5 seconds at the same
time.
To cancel the panic alarm, press any but-
ton (LOCK or UNLOCK). You can also turn
the ignition switch to the “ON” position to
cancel the panic alarm.
NOTE:
The panic alarm function will not activate
when the key is in the ignition switch.
NOTICE
7 K H W U D Q V P L W W H U L V D V H Q V L W L Y H H O H F
W U R Q L F L Q V W U X P H Q W 7 R D Y R L G G D P D J L Q J
W K H W U D Q V P L W W H U
Page 34 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
6 H F X U L W \ 6 \ V W H P L I H T X L S S H G The security system is armed in about 5
seconds after you lock all doors (including
the tailgate) by using the keyless entry sys-
tem transmitter, keyless push start system
remote controller or request switch.
Once the system is armed, any attempt to
open a door by using any other means (*)
than the keyless entry system transmitter,
keyless push start system remote control-
ler or request switch, or open the engine
hood, will cause the alarm to be triggered.
* These means include the following:
– The key
– The lock knob on a door
– The central door locking switchAlso, in case that you have set the shock
sensor to enabled state and set sensitivity
of the pre-warning function and full blast
warning function to a level other than 0, the
alarm will be triggered if any attempt is
made to tamper with the vehicle. The shock
sensor can be selected to enabled or dis-
abled state, and sensitivity of each warning
can be adjusted as desired. To set the
shock sensor, ask your D X W K R U L V H G 0 D U X W L
6 X ] X N L Z R U N V K R S or use the setting mode of
the information display.NOTE:
• The default setting of the shock sensor
is in the disabled state. Set to the
enabled state and adjust sensitivity of
each warning according to your prefer-
ence. For details on how to use the infor-mation display, refer to “Information
Display” in this section.
• Your dealer may have already set the
shock sensor of the vehicle to the
enabled state before you purchase it.
Consult your dealer for further informa-
tion.
NOTE:
• The security system generates alarms
when any of the predetermined condi-
tions is met. However, the system does
not have any function of blocking unau-
thorized entry into the vehicle.
• Always use the keyless entry system
transmitter, keyless push start system
remote controller or request switch to
unlock the doors when the security sys-
tem has been armed. Using a key
instead will trigger the alarm.
• If a person who does not know the secu-
rity system is going to drive the vehicle,
we recommend you explain the system
and its operation to the person, or dis-
able the system beforehand. Mistakenly
triggering the alarm may cause a nui-
sance to others.
• Even if the security system is armed,
you should still be careful to guard
against theft. Do not leave money or
things of value in the vehicle. + R Z W R D U P W K H V H F X U L W \ V \ V W H P
Z K H Q H Q D E O H G
Lock all doors (including the tailgate) using
the keyless entry system transmitter, key-
less push start system remote controller or
request switch. The security system indica-
tor (1) will start blinking rapidly, and the
security system will be armed in about 5
seconds.
While the system is being armed, the indi-
cator continues to blink at intervals of
approximately 2 seconds
61MM0A134
NOTE:
• To prevent the alarm from being acci-
dentally triggered, avoid arming it while
anyone remains inside the vehicle. The
alarm will be triggered if any person
inside opens the door or engine hood, or
swings the vehicle (if the shock sensor is
in the enabled state).
• The security system is not armed when
all doors are locked using the key from
(1)
Page 35 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
outside, or using the door lock knobs or
the central door locking switch from
inside.
• If any door is not operated within approx-
imately 30 seconds after the doors have
been unlocked using the keyless entry
system transmitter, keyless push start
system remote controller or request
switch, the doors are automatically
locked again. When the doors are
locked, the security system will be
armed in about 5 seconds if the system
is in the enabled state.
• If the security system indicator (1) blinks
when the ignition switch is in the “ON”
position or the ignition mode is “ON”,
there may be something wrong with the
security system. Ask your
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S to
inspect the system.
+ R Z W R G L V D U P W K H V H F X U L W \ V \ V W H P
Simply unlock the doors using the keyless
entry system transmitter, keyless push
start system remote controller or request
switch. The security system indicator will
go out, indicating that the security system
is disarmed.
+ R Z W R V W R S W K H D O D U P
Should the alarm be triggered accidentally,
unlock the doors using the keyless entry
system transmitter, keyless push start sys-
tem remote controller or request switch, or
insert the key in the ignition switch and turn
it to “ON” position, or press the engineswitch to change the ignition mode to
“ON”. The alarm will then stop.
NOTE:
• Even after the alarm has stopped, if you
lock the doors using the keyless entry
system transmitter, keyless push start
system remote controller or request
switch, the security system will be
rearmed with a delay of about 5 sec-
onds.
• If you disconnect the battery while the
security system is in the armed condition
or the alarm is actually in operation, the
alarm will be re-triggered when the bat-
tery is then reconnected.
• Even after the alarm has stopped at the
end of the predetermined operation time,
it will be triggered again if any of the
doors or engine hood is opened, or the
vehicle feels a shock (if the shock sen-
sor is in the enabled state), without dis-
arming the security system.
& K H F N L Q J Z K H W K H U W K H D O D U P K D V E H H Q
W U L J J H U H G G X U L Q J S D U N L Q J
If the alarm was triggered and you then
turn the ignition switch to “ON” position, or
press the engine switch to change the igni-
tion mode to “ON”, the security system
indicator will blink rapidly for about 8 sec-
onds and a buzzer will beep 4 times during
this period. If this happens, check whether
the vehicle has been broken into while you
were away from it. ( Q D E O L Q J D Q G G L V D E O L Q J W K H V H F X U L W \
V \ V W H P
The security system can be either enabled
or disabled.
: K H Q H Q D E O H G
• If any of the doors are opened without
unlocking by the keyless entry system
transmitter, keyless push start system
remote controller or request switch, all
turn signal lights start to blink and the
interior buzzer beeps intermittently. After
5 seconds, the siren will sound for about
27.5 seconds. The security system indi-
cator continues to blink during this time.
• If the engine hood is opened, all turn sig-
nal lights blink, and the siren sounds for
about 27.5 seconds. The security sys-
tem indicator continues to blink during
this time.
( , I W K H V K R F N V H Q V R U L V L Q W K H H Q D E O H G
V W D W H
• If the vehicle feels a shock, the siren
sounds for about 2 seconds (pre-warn-
ing). If the vehicle continues to feel a
shock, all turn signal lights start to blink
and the interior buzzer beeps intermit-
tently. After 5 seconds, the siren will
sound for about 27.5 seconds (full blast
warning). The security system indicator
continues to blink during this time.
NOTE:
If you set the full blast warning sensitivity
higher than the pre-warning sensitivity in
the setting mode of the information display,
or the vehicle feels such shock as to be
Page 105 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
NOTE:
In the presence of strong radio signals or
noise, you may not be able to change the
ignition mode to ACC or ON or to start the
engine using the engine switch. In this
case, the information display on the instru-
ment cluster will show the following mes-
sage: KEY FOB NOT DETECTED. 8 Q U H O H D V H G 6 W H H U L Q J / R F N : D U Q L Q JIf the steering lock remains engaged when
you press the engine switch to change the
ignition mode to “ON”, the information dis-
play in the instrument cluster shows the
message: “TRN. STEERING WHEEL TO
RELEASE LOCK”. Refer to “Information
Display” in the ³ % ( ) 2 5 ( ' 5 , 9 , 1 * ´ sec-
tion for details.
NOTE:
The steering lock may not be released if
some load is acting on the steering wheel.
If this happens, turn the steering wheel to
the right or left to relieve it from the load
before you press the engine switch again
to change to the desired ignition mode.
. H \ O H V V 3 X V K 6 W D U W 6 \ V W H P
L I H T X L S S H G Provided the keyless push start system
remote controller is within the “interior
workable area” (refer to the related expla-
nation in this section), you can use the
engine switch for starting the engine and
selecting an ignition mode (ACC or ON). In
addition, the following functions can be
used:
• Keyless entry function. Refer to “Keyless
Push Start System Remote Controller” in
the “BEFORE DRIVING” section for
details.
• Locking and unlocking doors (including
the tailgate) using a request switch.
Refer to “Keyless Push Start System
Remote Controller” in the “BEFORE
DRIVING” section for details.
• Immobilizer (anti-theft) function. Refer to
“Immobilizer System” in the “BEFORE
DRIVING” section for details. ( Q J L Q H 6 Z L W F K , O O X P L Q D W L R QThe engine switch is illuminated (lit) in the
following situations:
• When the engine is off and the driver’s
door is open or for 15 seconds after the
drivers door is closed.
• When the engine is off and the position
lights are on. The illumination will go out
when the position lights are turned off.
• When the engine is on and the position
lights and/or the headlights are on. Theillumination will go out when the head-
lights are turned off.
82K253
NOTE:
To save the battery, the illumination will be
automatically turned off when both of the
following conditions are simultaneously
met:
• The headlights and position lights are
turned off.
• A period of 15 minutes has elapsed after
opening the driver’s door. 6 H O H F W L R Q R I , J Q L W L R Q 0 R G H VPress the engine switch to select the
“ACC” or “ON” mode as follows when you
use an electric accessory or check the
operation of instruments without running
the engine.
1) Bring the keyless push start system
remote controller with you and sit in the
driver’s seat.