2015 MITSUBISHI L200 Owner's Manual (in English)

5.Push the wiper blade until the hook (B)
engages securely with the stopper (A).
Passenger’s side
1. Lift the wiper arm off the windscreen.
2. Pull the wiper blade until its stopper (A)
disengages from the hook (B). Then, pull the wiper blade further to remove it.
NOTEl Do not allow the wiper arm to fall onto the
windscreen; it could damage the glass.
3. Attach the retainers (C) to a new wiper
blade.
Refer to the illustration to ensure that the
retainers are correctly aligned as you at- tach them.
4. Insert the wiper blade into the arm, start-
ing with the opposite end of the blade from the stopper. Make sure the hook(B) is fitted correctly in the grooves inthe blade.
NOTEl If retainers are not supplied with the new
wiper blade, use the retainers from the old
blade.
5. Push the wiper blade until the hook (B)
engages securely with the stopper (A).
General maintenance
E01002700113
Fuel, engine coolant, oil and ex-
haust gas leakage
Look under the body of your vehicle to check
for fuel, engine coolant, oil and exhaust gas
leaks.
General maintenance
10-19OKTE15E3Maintenance10

WARNINGlIf you see a suspicious fuel leak or if you
smell fuel, do not operate the vehicle; werecommend you to call for assistance.
Exterior and interior lamp op-
eration
Operate the combination lamp switch to
check that all lamps are functioning properly.
If the lamps do not illuminate, the probable cause is a blown fuse or defective lamp bulb.
Check the fuses first. If there is no blown
fuses, check the lamp bulbs.
For information regarding the inspection and
replacement of the fuses and the lamp bulbs, refer to “Fuses” on page 10-20 and “Re-
placement of lamp bulbs” on page 10-25.
If the fuses and bulbs are all OK, we recom- mend you to have your vehicle checked and
repaired.
Meter, gauge and indicator/warning lamps operation
Run the engine to check the operation of all meters, gauges, and indicator/warning lamps.
If there is anything wrong, we recommend you to have your vehicle inspected.
Hinges and latches lubrication
Check all latches and hinges, and lubricate if
necessary by first cleaning and then applying
multipurpose grease.
For cold and snowy weather
E01002800257
Ventilation slots
The ventilation slots in front of the wind-
screen should be kept clear of leaves or brushed clear after heavy snowfall, so that
the operation of the heating and ventilation
systems will not be impaired.
Weatherstripping
To prevent freezing of the weatherstripping
on the doors, bonnet, etc., they should be treated with silicone grease or spray.
Additional equipment
It is a good idea to carry a shovel or a short- handled spade in the vehicle during the win-ter so that you can clear away snow if you get
stranded. A small hand-brush for sweeping snow off the vehicle and a plastic scraper for
the windscreen and rear window are also use- ful.
Fusible links
E01002900030
The fusible links will melt to prevent a fire if
a large current attempts to flow through cer- tain electrical systems.
In case of a melted fusible link, we recom- mend you to have your vehicle inspected.Fuses
E01003000849Fuse block location
E01007600032
To prevent damage to the electrical systemdue to shortcircuiting or overloading, each in-dividual circuit is provided with a fuse.
There are fuse blocks in the passenger com- partment and in the engine compartment.
For cold and snowy weather
10-20OKTE15E3Maintenance10

Passenger compartment
The fuse block in the passenger compartmentis located in front of the driver’s seat at the
position shown in the illustration.
Engine compartment
In the engine compartment, the fuse block is located as shown in the illustration.
1- Push the knob.
2- Remove the cover.
Fuse load capacity
E01007700033
The fuse capacity and the name of the electri- cal systems protected by the fuses are indica-ted on the inside of the fuse lid located at the
driver’s leg area and on the inside of the fuse block cover for fuses located in the engine
compartment.
Passenger compartment fuse lo-
cation table
E01007900501
NOTEl Spare fuses are contained in the fuse lid. Al-
ways use a fuse of the same capacity for re-
placement.Passenger compartment fuse location (LHD)
Fuses
10-21OKTE15E3Maintenance10LHD RHD

Passenger compartment fuse location (RHD)
No.SymbolElectrical system
Ca-
paci- ty1Tail lamp (left)7.5 A2Cigarette lighter15 A3Ignition coil10 A4Starter motor7.5 A5Sunroof20 ANo.SymbolElectrical system
Ca-
paci- ty6Accessory socket15 A7Tail lamp (right)7.5 A8Outside rear-view mir- rors7.5 A9Engine control unit7.5 A10Control unit7.5 A11Rear fog lamp10 A12Central door lock15 A13Room lamp10 A14Rear window wiper15 A15Gauge7.5 A16Relay7.5 A17Heated seat20 A18Option10 A19Heated door mirror7.5 A20Windscreen wiper20 A21Reversing lamps7.5 A22Demister30 ANo.SymbolElectrical system
Ca-
paci- ty23Heater30 A24Power seat40 A25Radio10 A26Electronic controlled unit15 A27—Spare fuse7.5 A28—Spare fuse20 A29—Spare fuse30 A
lSome fuses may not be installed on your
vehicle, depending on the vehicle model
or specifications.
l The table above shows the main equip-
ment corresponding to each fuse.
The fuse block does not contain spare 10
A and 15 A fuses. If a fuse of one of these capacities blows, replace it tempo-
rarily by borrowing the one that matches
from:
10 A: Radio
15 A: Cigarette lighter
Replace the borrowed fuse as soon as
possible.
Fuses
10-22OKTE15E3Maintenance10

Engine compartment fuse loca-tion table
E01008000583
Engine compartment fuse locationFront
No .SymbolElectrical system
Ca-
paci- ty1———2Electric window sys-
tem40 ANo .SymbolElectrical system
Ca-
paci- ty3Ignition switch40 A4Air conditioning com-
pressor10 A5Condenser fan motor20 A6Headlamp high-beam
(left)10 A7Headlamp high-beam
(right)10 A8Headlamp low beam
(left)10 A9Headlamp low beam
(right)10 A10Engine control20 A11Alternator7.5 A12Stop lamps15 A13Horn10 A14Automatic transmis-
sion20 A15Hazard warning flash-
er10 A16Fuel pump15 ANo .SymbolElectrical system
Ca-
paci- ty17Front fog lamps15 A18Audio amp20 A
l Some fuses may not be installed on your
vehicle, depending on the vehicle model
or specifications.
l The table above shows the main equip-
ment corresponding to each fuse.
Identification of fuse
E01008100308
CapacityColour7.5 ABrown10 ARed15 ABlue20 AYellow30 AGreen (fuse type)/
Pink (fusible link type)40 AGreen (fusible link type)Fuse replacement
E01007800656
1. Before replacing a fuse, always turn off
the electrical circuit concerned and place
the ignition switch in the “LOCK” posi-
tion.
Fuses
10-23OKTE15E3Maintenance10

2. Pull the fuse lid (A) to remove it.
3. Remove the fuse puller (B) from the fuse lid (A).
4.Referring to the fuse load capacity table,
check the fuse pertaining to the problem.
C- Fuse is OK
D- Blown fuse
NOTEl If any system does not function but the fuse
corresponding to that system is normal, theremay be a fault in the system elsewhere. We recommend you to have your vehiclechecked.5. Insert a new fuse of the same capacity
by using the fuse puller into the same
place at the fuse block.CAUTIONl If the newly inserted fuse blows again after a
short time, we recommend you to have the electrical system checked to find the causeand rectify it.
l Never use a fuse with a capacity larger than
that specified or any substitute, such as wire,
foil, etc.; doing so will cause the circuit wir-
ing to heat up and could cause a fire.
Fuses
10-24OKTE15E3Maintenance10LHD RHD

Replacement of lamp bulbsE01003100710
Before replacing a bulb, ensure the lamp is off. Do not touch the glass part of the new
bulb with your bare fingers; the skin oil left
on the glass will evaporate when the bulb gets hot and the vapour will condense on the
reflector and dim the surface.CAUTIONl Bulbs are extremely hot immediately after
being turned off.
When replacing a bulb, wait for it to cool sufficiently before touching it. You couldotherwise be burnt.NOTEl If you are unsure of how to carry out the
work as required, we recommend you to consult a specialist.
l Be careful not to scratch the vehicle body
when removing a lamp or lens.
l When it rains or when the vehicle has been
washed, the inside of the lens sometimes be-
comes foggy. This is the same phenomenon as when window glass mists up on a humid
day, and does not indicate a functional prob- lem. When the lamp is switched on, the heat
will remove the fog. However, if water gath-
ers inside the lamp, we recommend you to have the lamp checked.Bulb capacity
E01003200085
When replacing a bulb, use a new bulb with
the same wattage and colour.
Outside
E01003304169
Front
1- Headlamps, high-beam: 60 W (HB3)2- Headlamps, low beam: 55 W (H11)
3- Front turn-signal lamps: 21 W (PY21W)
4- Position lamps: 5 W (W5W)
5- Front fog lamps*: 55 W (H11)
6- Side turn-signal lamps (on fender)*: 5 W
(WY5W)
7- Side turn-signal lamps (on outside rear-
view mirror)*Type 2
1- Headlamps, high/low beam: 60/55 W
(H4)
2- Position lamps: 5 W (W5W)
3- Front turn-signal lamps: 21 W (PY21W) 4- Front fog lamps*: 55 W (H11)
5- Side turn-signal lamps (on fender)*: 5 W
(WY5W)
6- Side turn-signal lamps (on outside rear-
view mirror)*

Codes in parentheses indicate bulb types.
Replacement of lamp bulbs
10-25OKTE15E3Maintenance10 Type 1

NOTElThe side turn-signal lamp (on outside rear-
view mirror) uses an LED instead of a bulb. For repair and replacement, contact a
MITSUBISHI MOTORS Authorized Serv-
ice Point.
Rear
Type 1Type 2
1- High-mounted stop lamp: 5 W (W5W)
2- Rear turn-signal lamps: 16 W (W16W)3- Tail and stop lamps: 21/5 W (P21/5W)
4- Reversing lamps: 16 W (W16W)
5- Rear fog lamp (Type 1, Driver’s side on-
ly): 21 W (P21W)
6- Rear fog lamp (Type 2, Driver’s side on-
ly): 21 W (W21W)
7- Licence plate lamps: 5 W (W5W)

Codes in parentheses indicate bulb types.Inside
E01003401518
Single cab
1- Door courtesy lamps*: 3.4 W
2- Room lamp: 8 W
3- Glove box lamp: 1.4 W
4- Centre console downlight: 1.4 W
Club cab
1- Door courtesy lamps*: 3.4 W
2- Front room lamp and personal lamps*: 7.5 W
3- Rear room lamp: 8 W
4- Glove box lamp: 1.4 W
5- Centre console downlight: 1.4 W
Replacement of lamp bulbs
10-26OKTE15E3Maintenance10