2015 MITSUBISHI L200 Owner's Manual (in English)

When the outside air temperature drops be-low about 3 °C (37 °F) , the alarm sounds and
the outside air temperature warning symbol (A) flashes for about 10 seconds.CAUTIONl There is a danger the road might be icy, even
when this symbol is not flashing, so please take care when driving.Altimeter
E00518600069
The current elevation in units of 100 m (400
ft) is shown in (A). The elevation is graphed every 5 minutes and the data for up to 4 hours are shown in (B).
To adjust the elevation
It is possible to adjust the currently indicated
elevation using the following function but-
tons:
“+”-Adjustment of elevation
The elevation increases by 100
m (400 ft) every time you light- ly push the “+” button.
If you continue pressing the but- ton for about 2 seconds or more,
the elevation indication is fast-
forwarded. Then the setting is changed to the elevation selec-
ted.“-”-Adjustment of elevation
The elevation decreases by 100
m (400 ft) every time you light- ly push the “-” button.
If you continue pressing the but- ton for about 2 seconds or more,
the elevation indication is fast- forwarded. Then the setting is
changed to the elevation selec- ted.NOTEl The elevation is determined from changes in
atmospheric pressure. Depending on weather
conditions, the indicated elevation may dif- fer from the actual elevation. Variations in
atmospheric pressure can cause different ele- vations to be shown even in the same loca-
tion. This behavior does not indicate a fault.
Use the indication as a guide only.
Centre information display*
5-17OKTE15E3Instruments and controls5

Resetting the elevation
Press the “RESET” function button to reset
the elevation plotted in graph.
NOTEl Pressing the “RESET” function button will
not reset the indication (C).
l It is possible to set the display unit to m or
ft.
Refer to “User customization” on page 5-27.Barometer
E00518700044
This display shows the atmospheric pressure
at the present location in (A). The atmospher- ic pressure values are graphed every5 minutes and the data for up to 4 hours are
shown in (B).
Resetting the atmospheric pressure
Press the “RESET” function button to reset
the atmospheric pressure plotted in graph.
NOTEl Pressing the “RESET” function button will
not reset the indication (C).
l It is possible to set the display unit to hPa,
mb, kPa, or inHg.
Refer to “User customization” on page 5-27.Calendar
E00518800032
The date is shown. The calendar pattern can
be changed to your desired setting.
Refer to “Changing the calendar setting” on page 5-24.
Clock-only
E00518900033
Only the clock is shown. The time notation
can be changed to your desired setting. (12 hour/24 hour)
Centre information display*
5-18OKTE15E3Instruments and controls5

Refer to “User customization” on page 5-27.Blank
E00519000015
The whole display can be turned into blank.
In this case, buttons remain illuminated.
NOTEl If you operate the audio system, the audio
display pops up.Selecting settings displays
E00519100090
Every time the “ADJ” button is pressed light-
ly, the display can be changed to the follow-ing:
CAUTIONl The driver should not operate the display
while the vehicle is in motion.
l When operating the system, stop the vehicle
in a safe area.
1- Changing the clock settings ® p. 5-20
2- Adjusting the display brightness ® p. 5-21
3- Correcting the compass ® p. 5-22
4- Changing the calendar setting ® p. 5-24
5- User customization ® p. 5-27
6- Adjusting the barometer ® p. 5-30
Centre information display*
5-19OKTE15E3Instruments and controls5 TA0024955

Changing the clock settings
E00519200121
1. Press the “ADJ” button to select the
clock setting display.
2. It is possible to adjust the clock using
the function buttons.
“H”-Adjust “hour”.
The indication increases by one
hour, every time you lightly press the “H” function button. If you con-tinue pressing the button for about 2 seconds or more, the indication is fast-forwarded, and then the settingis changed to the hour selected.“M”-Adjust “minute”.
The indication increases by one mi-
nute, every time you lightly press
the “M” function button. If you con- tinue pressing the button for about 2 seconds or more, the indication is fast-forwarded, and then the settingis changed to the minute selected.“SET”
-To reset the minutes to zero.
The time is adjusted as described be-
low by pressing the function button
“SET”.
l 10:30-11:29 · · · · change to
11:00
l 11:30-12:29 · · · · change to
12:00
In this occasion, the display flashes twice and then the setting is changed.
Centre information display*
5-20OKTE15E3Instruments and controls5

3.After making the adjustment, press the
“INFO” button to select the information display.Adjusting the display bright-
ness
E00519300034
The display brightness can be adjusted at 13
levels for both daytime and nighttime.
l BRIGHTNESS FOR DAY TIME
The display brightness is adjusted when the light switch is in the “OFF” position.
l BRIGHTNESS FOR NIGHT TIME
The display brightness is adjusted when the light switch is in the “
” or “”
position.
1. Press the “ADJ” button to show the
brightness adjusting display.
2. Press the “←” or “→” function button to
select the setting you wish to adjust (daytime or nighttime). Then press the
“SELECT” function button.
3. Use the function buttons to adjust the
brightness.
“+”-To make the display brighter
The display becomes brighter by one step, every time you lightly
press the “+” function button. If you
continue pressing the button for
about 2 seconds or more, the indica- tion is fast-forwarded.“-”-To make the display darker
The display becomes darker by one step, every time you lightly press the
“-” function button. If you continue pressing the button for about
2 seconds or more, the indication is fast-forwarded.“SET” -To set the brightness
Press function button “SET” to set
the new brightness. The display will flash twice.
Centre information display*
5-21OKTE15E3Instruments and controls5

NOTElIf you next wish to adjust the other adjust-
ment setting (daytime or nighttime), press
the “ADJ” button or “BACK” function but- ton.
4. After adjustment, press the “INFO” but-
ton to select the information display.
NOTEl As the display brightness can be adjusted in
the center information display only, the
brightness inside the meter cannot be changed.Correcting the compass
E00519400178
This compass shows the direction of the vehi-
cle by the 8 azimuth system.NOTEl This system uses the earth’s magnetic field,
and so may not show the correct direction
depending on the traffic condition or in the following places where the earth’s magnetic
field is disrupted.
• Car parks located in buildings and tunnels
• Expressways and underground cables
• Area over the subway
• Transforming station
• Areas along the railroad
In these cases, the correct direction will be displayed once the vehicle returns to a place
where the earth’s magnetic field is stable.NOTEl Do not install ski racks, antennas, etc. which
are attached to the vehicle by means of a
magnet. They affect the operation of the
compass.
Setting the declination
The declination is the difference between true
north (the direction of the geographic north pole) and where a compass needle points to.
Since the declination varies from place to place, it needs to be set for each region. Oth-erwise the compass will not show the correct
direction.
Set the declination by the following steps:
Centre information display*
5-22OKTE15E3Instruments and controls5

NOTElThe default declination setting is 0 degrees
.
In accordance with the illustration, set the
declination setting to the declination contour
nearest to a region where you drive the vehi- cle.
l The declination can be set at intervals of
1 degrees, from 28 degrees west (W28) to 28 degrees east (E28).
With a settings display showing, press the
“ADJ” button and select “COMPASS VAR-
IANCE”. 1. Press the function button for “SELECT”.
2. Press the function button for “←” or
“→” to set the desired declination.

Pressing “←” or “→” for more than 1
second makes the value change rapidly.
3. When the declination adjustment has
been completed, press the “SET” func-
tion button.
Setting the compass
The compass is usually calibrated automati-
cally when the vehicle is moving. At times when complete calibration is not possible, nocompass indications are given. Manually set
the compass using the following procedure.
NOTEl If your vehicle has a sunroof, keep the sun-
roof closed when calibrating the compass.
Having the sunroof open when calibrating the compass could render the compass un-
able to correctly show directions.
With a settings display showing, press the
“ADJ” button and select “COMPASS CALI-
BRATION”.
Centre information display*
5-23OKTE15E3Instruments and controls5

1. Press the function button for “SELECT”.
2. Press the function button for “SELECT”.
3.Turn the vehicle slowly through
360 degrees in a safe, open area with no buildings and other vehicles.NOTEl If you wish to stop calibrating the compass
part-way through the procedure, press the“INFO” button or “ADJ” button.NOTEl The “Completed the calibration”. message
may be displayed even if you terminate the
turn before it is complete and return to the vehicle’s original direction. The compass
may not be properly calibrated in this case, so you must turn the vehicle through at least
360 degrees.
4. The compass setting will finish automat-
ically and the words “COMPASS CALI-
BRATION COMPLETE” will appear on the screen.
Changing the calendar setting
E00519501091
The date and the calendar indication patternscan be changed.
Centre information display*
5-24OKTE15E3Instruments and controls5