2015 MITSUBISHI L200 traction control

Indication and warning lampsE005015035331. CRUISE indication lamp* ® p. 6-51
2. Turn-signal indication lamps/Hazard warning indication lamps ® p. 5-07
3. High-beam indication lamp ® p. 5-07
4. Front fog lamp indication lamp* ® p. 5-07
5. Rear fog lamp indication lamp ® p. 5-07
6. Seat belt reminder/warning lamp ® p. 4-11
7. Low fuel warning lamp ® p. 5-05
8. 2WD/4WD operation indication lamp* ® p. 6-27, 6-329. Rear differential lock indication lamp*
® p. 6-35
10. Check engine warning lamp ® p. 5-08
11. Diesel preheat indication lamp ® p. 5-07
12. Oil pressure warning lamp ® p. 5-09
13. Fuel filter indication lamp ® p. 5-08
14. Charge warning lamp ® p. 5-09
15. A/T (automatic transmission) fluid tem- perature warning lamp (vehicles with
A/T) ® p. 6-23
16. Selector lever position indicator (vehi- cles with A/T) ® p. 6-2017. Diesel particulate filter (DPF) warning
lamp* ® p. 6-15
18. Brake warning lamp ® p. 5-08
19. Active Stability & Traction Control (ASTC) OFF indication lamp*
® p. 6-49
20. Anti-lock brake system (ABS) warning lamp* ® p. 6-46
21. Active Stability & Traction Control (ASTC) indication lamp* ® p. 6-49
22- Door ajar warning lamp ® p. 5-10
23. Supplemental restraint system (SRS) warning lamp* ® p. 4-40
Indication and warning lamps
5-06OKTE15E3Instruments and controls5Type 1Type 2

Economical driving............................................................................. 6-02
Driving, alcohol and drugs.................................................................. 6-02
Safe driving techniques....................................................................... 6-03
Running-in recommendations............................................................. 6-04 Parking brake...................................................................................... 6-07
Parking................................................................................................ 6-08
Steering wheel height adjustment....................................................... 6-09
Inside rear-view mirror....................................................................... 6-09 Outside rear-view mirrors................................................................... 6-10
Ignition switch.....................................................................................6-12 Steering wheel lock............................................................................. 6-13
Starting................................................................................................ 6-13 Diesel particulate filter (DPF)*........................................................... 6-15Manual transmission........................................................................... 6-16Automatic transmission Sports Mode 4A/T, 5A/T............................. 6-19Easy select 4WD*............................................................................... 6-25
Super select 4WD*..............................................................................6-29
Rear differential lock*........................................................................ 6-34 4-wheel drive operation...................................................................... 6-38
Inspection and maintenance following rough road operation............. 6-41
Cautions on handling of 4-wheel drive vehicles................................. 6-41
Limited-slip differential*.................................................................... 6-43
Braking................................................................................................ 6-43
Brake assist system*........................................................................... 6-44
Anti-lock brake system (ABS)*.......................................................... 6-45
Power steering system.........................................................................6-48 Active Stability & Traction Control (ASTC)*....................................6-48
Cruise control*.................................................................................... 6-50 Cargo loads......................................................................................... 6-55Trailer towing......................................................................................6-55Starting and driving
OKTE15E36

NOTElIt is recommended to start the vehicle with
parking brake partially, but not completely,applied by slightly pulling the parking brake
lever.
After the vehicle has become free, do not forget to release the parking brake.
l If it is necessary to drive in extremely mud-
dy conditions, the use of tyre chains is rec-
ommended. Because the extent of muddy conditions is difficult to judge and the vehi- cle could become bogged down very deeply,
operation should be at a low speed. If possi-
ble, get out of the vehicle and check the con- ditions ahead before proceeding.
l Driving over roads in coastal areas or roads
on which anti-skid preparations have been spread can cause rust on the vehicle; wash
the vehicle thoroughly as soon as possible
after such use.
Climbing sharp grades
Set the transfer shift lever to “4L” position
(easy select 4WD), “4LLc” position (super
select 4WD) to maximize the engine torque.
WARNINGl Go straight up. Do not try to traverse
across a steep slope.WARNINGl If you begin to lose traction, ease off the
accelerator pedal and gently turn the
steering wheel alternatively left and right to regain adequate traction again.NOTEl Choose as smooth a slope as possible with
few stones or other obstacles.
l Before attempting to drive up the slope,
walk up it to confirm that the vehicle canhandle the grade.
Descending sharp grades
Set the transfer shift lever to “4L” position
(easy select 4WD), “4LLc” position (super
select 4WD), use the engine brake (down- shifting) and descend slowly.
WARNINGl Avoid snaking down a sharp grade. De-
scend the grade as straight as possible.NOTEl When descending a sharp grade, if the
brakes are applied suddenly because of an
obstacle encountered, control of the vehicle
could be lost. Before descending the slope,
walk down it and confirm the path.NOTEl Before descending a grade, it is necessary to
choose the appropriate gear. Avoid changing
gears or depressing the clutch while de-
scending the grade.
l MITSUBISHI
MOTORS is not responsible
to the operator for any damage or injury caused or liability incurred by improper and
negligent operation of a vehicle. All techni- ques of vehicle operation described herein depend on the skill and experience of the op- erator and other participating parties and any
deviation from the recommended operation
instructions above is at their own risk.
Turning sharp corners
When turning a sharp corner in “4H” or “4L”
position (easy select 4WD), “4HLc” or “4LLc” position (super select 4WD) at low speed, a slight difference in steering may be
experienced similar to as if the brakes were applied. This is called tight corner braking and results from each of the 4 tyres being at a
different distance from the corner.
The phenomenon is peculiar to 4-wheel drive vehicles. If this occurs, either straighten the steering wheel, or change to rear-wheel drive.
4-wheel drive operation
6-40OKTE15E3Starting and driving6

CAUTIONlThe brake assist system is not a device de-
signed to exercise braking force greater than its capacity. Make sure to always keep a suf-
ficient distance between vehicles in front of
you without relying too much on the brake
assist system.NOTEl Once the brake assist system is operational,
it maintains great braking force even if the
brake pedal is lightly released.
To stop its operation, completely remove
your foot from the brake pedal.
l When the brake assist system is in use while
driving, you may feel the brake pedal at-
tempt to resist, the pedal moves in small mo- tions in conjunction with the operation
noise, or the vehicle body and the steering wheel vibrate. This occurs when the brake
assist system is operating normally and does not indicate faulty operation. Continue to
firmly depress the brake pedal.
l When the active stability & traction control
(ASTC) indication lamp is illuminated, the
brake assist system may not function.Anti-lock brake system
(ABS)* E00607100775
Environmental conditions can have an effect
on braking. During sudden braking when there is snow, ice, oil, water etc. on the road
surface, a skid may occur. In this situation, steering control and braking effectiveness is
reduced and the stopping distance is in-
creased. The vehicle may also go into an un- controlled spin.
The ABS helps prevent the wheels from lock-
ing during braking, thus maintaining direc-
tional stability, ensuring controllability and
providing optimum braking force.
Driving hints
l With ABS fitted, steering during sudden
braking (when the ABS functions) dif- fers slightly from when the brakes are
not being applied.
Steer the vehicle carefully in these con-
ditions.
l Always maintain the same distance from
the vehicle in front of you as you would for a vehicle not equipped with ABS.
Compared with vehicles not fitted with ABS, your vehicle may require a longer
stopping distance in the following cases: • Driving on gravel or snow-covered
roads.
• Driving with tyre chains installed.
• Driving on roads where the road sur-
face is pitted or has other differences in surface height.
• Driving on bumpy roads or other poor
driving surfaces.
l Operation of ABS is not restricted to sit-
uations where brakes are applied sud-denly. This system may also operate to
prevent wheel lock when you are driving
over manholes, steel road-work plates, or the vehicle is driven over steps or lev-
el differences in the road, road markings,
or other surfaces which are difficult for
the wheels to grip.
l When the ABS is activated, you may
feel the brake pedal pulsation and hear a
characteristic noise. Also at this time, you may feel as if the pedal attempts to
resist being depressed.
In this situation, to let the ABS work for you, just hold the brake pedal
down more firmly. Do not pump the brake. This pumping will result in re-duced braking performance.
Anti-lock brake system (ABS)*
6-45OKTE15E3Starting and driving6

CAUTIONlEven the ABS cannot prevent the natural
laws of physics from acting on the vehicle. Itcannot for instance avoid accidents that may
result from excessive speed on bends or fol- lowing another vehicle too closely or aqua- planing. It should remain the driver’s task to
observe safety precautions to judge speeds and brake applications correctly in such con-
ditions.
l Be sure to use tyres of the same type and
size on 4 wheels.
If tyre types or sizes are mixed, ABS may not function normally.
l Never install a limited-slip differential,
which is not a MITSUBISHI MOTORS gen-
uine part, as the ABS may not function nor-
mally.
We recommend you to consult a MITSUBISHI MOTORS Authorized Serv-
ice Point.ABS warning lamp
E00607201164
The ABS warning lamp should illuminate
when the ignition switch is turned “ON”, and
should go off in a few seconds.
CAUTIONl If the warning lamp stays on or does not illu-
minate when you start the vehicle, it indi-
cates that the ABS is not functioning and
that only the standard brake system is in op-
eration. (In this condition the standard hy- draulic brake system will still function.) We
recommend you to have your vehicle inspec- ted as soon as possible.NOTEl On vehicles with the rear differential lock,
ABS and the active stability & traction con-
trol (ASTC) functions are suspended while the rear differential lock is activated.
ASTC indication lamp, Active Stability
Control function OFF indication lamp, ABS warning lamp and brake warning lamp are
illuminated while these functions are sus- pended.
It does not indicate a problem. When the
rear differential lock is disengaged, these lamps go out and function again.
Refer to “ASTC indication lamp, ASTC
OFF indication lamp” on page 6-49.
l On vehicles with rear differential lock, ABS
functionality is suspended while the rear dif- ferential lock is operating.
The ABS warning lamp is illuminated while ABS functionality is suspended. It does notindicate a problem. When the rear differen-
tial lock is disengaged, the ABS warning
lamp goes off and the ABS functions again.
Refer to “Rear differential lock” on page
6-34.
Anti-lock brake system (ABS)*
6-46OKTE15E3Starting and driving6

Power steering systemE00607400387
The power steering system operates while the
engine is running. It helps reduce the effort needed to turn the steering wheel.
The power steering system has mechanical
steering capability in case the power assist is lost. If the power assist is lost for some rea-
son, you will still be able to steer your vehi-
cle, but you will notice it takes much more effort to steer. If this happens, have your ve-
hicle inspected at an authorized MITSUBISHI MOTORS service point.WARNINGl Do not stop the engine while the vehicle is
moving. Stopping the engine would make
the steering wheel extremely hard to turn, possibly resulting in an accident.CAUTIONl Do not leave the steering wheel turned all
the way in one direction. This can causedamage to the power steering system.Active Stability & Traction
Control (ASTC)* E00616700344
The active stability & traction control (ASTC) takes overall control of the anti-lockbrake system, traction control function and Active Stability Control function to help
maintain the vehicle’s control and traction. Please read this section in conjunction with the page on the anti-lock brake system, trac- tion control function and Active Stability
Control function.

Anti-lock brake system (ABS) ® p. 6-45
Active Traction Control function ® p. 6-49
Active Stability Control function ® p. 6-49CAUTIONl Do not over-rely on the ASTC. This system,
like any other system, has limits and cannot
help you to maintain traction and control of
the vehicle in all circumstances. Reckless
driving may lead to accidents. Always drive carefully, taking into account the traffic,road and environmental conditions.
l Be sure to use the same specified type and
size of tyre on all 4 wheels. Otherwise, the
ASTC may not work correctly.NOTEl After your vehicle is driven a short distance
after starting the engine, a click is heard from the engine compartment; however, this
is only the sound of ASTC being checked.
l Some vibration will be felt in the vehicle
body and a whining sound of a motor will be heard from the engine compartment when the ASTC functions. This is a normal result
of the ASTC operation, and does not indi- cate a malfunction.
l The ASTC does not operate while the ABS
warning lamp is illuminated.
l On vehicles with the rear differential lock,
the ASTC and ABS functions are suspended
while the rear differential lock is activated. ASTC indication lamp, ASTC OFF indica-tion lamp and ABS warning lamp are illumi-
nated while these functions are suspended. It
does not indicate a problem. When the rear differential lock is disengaged, these lamps
go out and function again.
Refer to “ABS warning lamp” on page 6-46,
“ASTC indication lamp, ASTC OFF indica-
tion lamp” on page 6-49.
Power steering system
6-48OKTE15E3Starting and driving6

Driving hints
E00616800039
When extricating the vehicle from mud, sand
or fresh snow, you may find that operation of
the ASTC prevents the engine speed from in-
creasing in response to depression of the ac- celerator pedal. If this happens and the vehi-cle remains stuck as a result, deactivate the
ASC function by pressing the “ASC OFF”
switch. The vehicle will then be easier to ex- tricate. (Brake control of the ATC function isstill working to prevent wheel spins when the
ASC function is deactivated by pressing the “ASC OFF” switch.)
Active Stability Control func-
tion
E00616900115
The Active Stability Control function is de- signed to improve the vehicle’s stability byrestraining its tendency to slip sideways (for
example, when rounding a curve in slippery conditions, or when the driver takes rapid
steering action to avoid an obstacle). It works
by controlling the engine output and brake on each wheel.
NOTEl On vehicles with rear differential locks, the
Active Stability Control function does notoperate when the rear differential lock is ac-
tivated.
“ASC OFF” switch
The Active Stability Control function is auto-
matically activated when the ignition switch
is turned to the “ON” position. You can deac- tivate the system by pressing the “ASC OFF”
switch when the vehicle speed is below 40 km/h (25 mph). To reactivate the Active
Stability Control function, press the ASC OFF switch again. It is strongly recommen-
ded that the Active Stability Control function
normally be kept activated.
Type 1Type 2
NOTEl If the vehicle speed increases to about
120 km/h (74 mph) with the Active Stability Control function deactivated, the Active Sta-bility Control function automatically starts operating. To subsequently stop the Active
Stability Control function, stop the vehicle
and press the ASC OFF switch again.Active Traction Control func-
tion
E00617000025
On slippery surfaces, active traction control function prevents the drive wheels from ex- cessive spinning, thus helping the vehicle to
start moving from a stop. It also provides suf-
ficient driving force and steering perform- ance as the vehicle turns at accelerated
speeds.
CAUTIONl When driving a vehicle on a snowy or icy
road, be sure to install snow tyres and drive the vehicle at moderate speeds.ASTC indication lamp, ASTC
OFF indication lamp
E00617100114
The Active Stability Control function and ac-
tive traction control function share the same indication lamp.
Active Stability & Traction Control (ASTC)*
6-49OKTE15E3Starting and driving6

The indication lamps should illuminate when
the ignition switch is turned to the “ON” po- sition and should go off after a few seconds.
If the indication lamps stay on or do not illu- minate when the ignition switch is turned to
the “ON” position, we recommend you to have your vehicle inspected as soon as possi-ble.
indication lamp blinks when the Active
Stability Control function or active traction
control function is operating.
indication lamp is illuminated when the
Active Stability Control function is OFF.
CAUTIONl When indication lamp blinks, Active Sta-
bility Control function or active traction con- trol function is operating, which means that
the road is slippery or that your vehicle’s wheels are slipping excessively. If this hap-
pens, drive slower with less accelerator in-
put.CAUTIONl If an abnormal condition occurs in the sys-
tem while driving, the indication lamp
will illuminate.
In these cases, follow these procedures:
• If the temperature in the braking system
continues to increase due to continuous brake control on a slippery road surface,
the
indication lamp will illuminate, and
operation of the Active Stability Control function and active traction control func-
tion will be suspended to protect the brake
system. (Normal operation of the vehicle will not be affected.) Park your vehicle in
a safe place. When the temperature in the
braking system has come down, the
in-
dication lamp will go off and the Active
Stability Control function and active trac- tion control function will start operating again.
• If the
indication lamp does not go out
even though the above procedure is fol-
lowed, there could be a problem in the system.
Stop the engine and start the engine again
and check whether the
indication lamp
goes out. If the indication lamp goes out, there is no abnormal condition.
If the
indication lamp illuminates even
after your vehicle is driven a short dis-
tance after restarting the engine, we rec-
ommend you to have your vehicle checked as soon as possible.
CAUTIONl If the vehicle is towed with the ignition
switch in the “ON” position and only the
front wheels or only the rear wheels raised off the ground, the ASTC may operate, re-
sulting in an accident. When towing the ve- hicle with the front wheels raised, keep the
ignition switch in the “LOCK” or “ACC” position. When towing the vehicle with the
rear wheels raised, keep the ignition switch in the “ACC” position.
Refer to “Towing” on page 8-22.Cruise control*
E00609100779
Cruise control is an automatic speed controlsystem that keeps a set speed. It can be acti-vated at about 40 km/h (25 mph) or more.
Cruise control*
6-50OKTE15E3Starting and driving6