2015 LEXUS LX570 Owners Manual

1531-7. Safety information
1
Before driving
LX570_OM_OM60L96U_(U) Type A
Latch the hooks of the
lower straps onto the
LATCH anchors.
If the child restraint has a
top tether strap, the top
tether strap should be
latched onto the top tether
strap anchor.
For owners in Canada:
The symbol on a child restraint sys-
tem indicates the presence of a
lower connector system.
Type B
Latch the buckles onto the
LATCH anchors.
If the child restraint has a
top tether strap, the top
tether strap should be
latched onto the top tether
strap anchor.
For owners in Canada:
The symbol on a child restraint sys-
tem indicates the presence of a
lower connector system. Canada only STEP 3
STEP 4
Canada only STEP 3
STEP 4

1541-7. Safety information
LX570_OM_OM60L96U_(U) Installing child restraints using a se at belt (child restraint lock function
belt)
■ Rear-facing  Infant seat/Convertible seat
Fold the seatback while pulling the
seatback angle lever. Return the
seatback and secure it at the first
lock position. (  P. 71)
Place the child restraint system on
the second seat facing the rear of
the vehicle.
Run the seat belt through the child
restraint system and insert the
plate into the buckle. Make sure
that the belt is not twisted.STEP 1
STEP 2
STEP 3

1551-7. Safety information
1
Before driving
LX570_OM_OM60L96U_(U) Fully extend the sh oulder belt and
then allow it to retract slightly in
order to activate the ALR lock
mode. Lock mode allows the seat belt to
retract only.
While pushing the child restraint
system down into th e second seat,
allow the shoulder belt to retract
until the child restraint system is
securely in place. After the shoulder belt has
retracted to a point where there is
no slack in the belt, pull the belt to
check that it cannot be extended. STEP 4
STEP 5

1561-7. Safety information
LX570_OM_OM60L96U_(U) ■ Forward-facing  Convertible seat
Fold the seatback while pulling the
seatback angle lever. Return the
seatback and secure it at the first
lock position. (  P. 71)
Place the child restraint system on
the seat facing the front of the
vehicle.
Run the seat belt through the child
restraint system and insert the
plate into the buckle. Make sure
that the belt is not twisted.STEP 1
STEP 2
STEP 3

1571-7. Safety information
1
Before driving
LX570_OM_OM60L96U_(U) Fully extend the shoulder strap
and then allow it to retract slightly
into the ALR lock mode. Lock mode allows the seat belt to
retract only.
While pushing the child restraint
system into the second seat, allow
the shoulder belt to retract until
the child restraint system is
securely in place. After the shoulder belt has
retracted to a point where there is
no slack in the belt, pull the belt to
check that it cannot be extended.
If the child restraint system has a top tether strap, the top tether
strap should be latched onto the top tether strap anchor.
(  P. 152) STEP 4
STEP 5
STEP 6

1581-7. Safety information
LX570_OM_OM60L96U_(U) ■ Booster seat
Fold the seatback while pulling the
seatback angle lever. Return the
seatback and secure it at the first
lock position.
Place the child restraint system on
the seat facing the front of the
vehicle.
Sit the child in the child restraint
system. Fit the seat belt to the child
restraint system according to the
manufacturer’s instructions and
insert the plate in to the buckle.
Make sure that the belt is not
twisted. Check that the shoulder belt is cor-
rectly positioned over the child’s
shoulder, and that the lap belt is as
low as possible. (  P. 91)STEP 1
STEP 2
STEP 3

1591-7. Safety information
1
Before driving
LX570_OM_OM60L96U_(U) Removing a child restraint system installed with a seat belt
Push the buckle release button
and fully retract the seat belt.
Child restraint systems with a top tether strap
Secure the child restraint system using a seat belt or LATCH
anchors, and do the following.
Outside
Adjust the head restraint to the
upmost position.
Center
Lower the head restraint to the
lowest position.STEP 1

1601-7. Safety information
LX570_OM_OM60L96U_(U) Open the anchor bracket cover, latch the hook onto the anchor
bracket and tighten the top tether strap.
Outside
Make sure the top tether strap is
securely latched.
Center
Outside only: Adjust the head
restraint to the downmost position.STEP 2
STEP 3